Question is ⇒ Nichrome is commonly used for, Options are ⇒ (A) lamp filaments, (B) transformer winding, (C) heater coils, (D) battery connections, (E) , Leave your comments or Download question paper.

Question is ⇒ Nichrome is commonly used for, Options are ⇒ (A) lamp filaments, (B) transformer winding, (C) heater coils, (D) battery connections, (E) , Leave your comments or Download question paper. Previous question Next question


Q1.	Nichrome is commonly used for
A.	lamp filaments [Wrong Answer]
B.	transformer winding [Wrong Answer]
C.	heater coils [Correct Answer]
D.	battery connections [Wrong Answer]
View Answer 1 -1 Explanation:- Answer : C Discuss it below : !! OOPS Login [Click here] is required to post your answer/result Help other students, write article, leave your comments

Previous question Next question

Also Read Similar Questions Below :

⇒ Which of following antenna not produces circular polarisation?
Helical
Parabolic
Disc
Yagi

⇒ As applied to a flip flop the word edge triggered's means
flip flop can change state when clock transition occurs
flip flop can change state when clock signal goes from LOW to HIGH only
flip flop can change state when clock signal goes from HIGH to LOW only
none of the above

⇒ In a single stage differential amplifier, the output offset voltage is basically dependent on the mismatch of
V_BE, I_B and β
V_BE and I_B
I_B and β
V_BE and β

⇒ At 0 K, silicon and germanium behave like monoatomic crystals.
TRUE
FALSE

⇒

Assertion (A): C has a large number of library functions classified as arithmetic functions, data conversion functions, character classified functions, string manipulation functions, searching and sorting functions etc.

Reason (R): 8086 uses a segment : offset addressing scheme.

Both A and R are correct and R is correct explanation of A
Both A and R are correct but R is not correct explanation of A
A is correct R is wrong
A is wrong R is correct

⇒ LVDT is a
pressure transducer
displacement transducer
velocity transducer
acceleration transducer

⇒ With respect to the following 555 timer circuit what will be the value of R_A and R such that the LED turns on for a duration of 10 ms every time it receives negative trigger pulse. LED operating current = 20 mA, V_f = 1.4 V, Vo _on = 13.4 V and C = 0.22 nf
41.4 KΩ, 600 Ω
45 KΩ, 630 Ω
43.5 KΩ, 580 Ω
44.9 KΩ, 600 Ω

⇒ If the time is counted from the instant when an ac wave is at its peak value, we get a
sine wave
cosine wave
distorted sine wave
none of the above

⇒ If a and b are the width and height of rectangular wave-guide the cut off wavelength λ_c for TE₂₀ mode is equal to
a
a + b
a - b
a² + b²

⇒ The frequency tolerance for the RF carrier in the standard AM radio broadcast band is
zero
+20 Hz
+1000 Hz
+25 Hz

⇒ In pulse code modulation when the maximum frequency in the signal is f_max the bandwidth required will be
≤ p.f_max
≥ p.f_max
≤ (p.f_max)²
≥ (p.f_max)²

⇒ For the ring oscillator shown in the figure, the propagation delay of each inverter is 100 pico sec. What is the fundamental frequency of the oscillator output _______
10 MHz
100 MHz
1 GHz
2 GHz

⇒ The pure capacitor connected across an A.C. voltage consumed 20 W. This is due to
the capacitive reactance in ohms
the current flowing in the capacitor
the fused capacitor was a big one
none of the above

⇒ Both Impatt and Trapatt devices use avalanche effect
TRUE
FALSE

⇒ In a receiver, at higher frequencies
tracking will be improved
tracking will be poor
selectivity will be poor
image frequency rejection will be poor

⇒ In a certain network not containing any dependent sources, number of nodes = 4 and number of branches is equal to 6.
4
2
3
5

⇒ In a low level AM system, the modulated amplifiers stage must be
harmonic devices
non-linear devices
class C amplifier
linear devices

⇒ In high power AM transmission, modulation is done at
IF stage
buffer stage
RF stage
oscillator stage

⇒ For measuring temperatures below 800°C with high accuracy, the best instrument is
optical pyrometer
thermistor based thermometer
GaAs junction diode thermometer
platinum resistance thermometer

⇒ Loss angle of a good quality cable is about
1°
30°
70°
90°

⇒
Assertion (A): The reverse current in a p-n junction is nearly constant.
Reason (R): The reverse breakdown voltage of a p-n diode depends on the extent of doping.

Both A and R are true and R is correct explanation of A
Both A and R are true but R is not a correct explanation of A
A is true but R is false
A is false but R is true

⇒ Video signals are transmitted through
amplitude modulation
frequency modulation
either amplitude or frequency modulation
neither amplitude nor frequency modulation

⇒ Which of the following pulse-time modulation is least used?
PDM
PPM
PWM
PAM

⇒ In a sine wave, maximum rate of change of voltage occurs at
ascent of the waveform
+ ve maximum
- ve maximum
between maximum and minimum

⇒ In figure (A) and
A represents PCM and B represents AM
A represents FM and B represents AM
A represents AM and B represents FM
A represents PCM and B represents FM

⇒
Assertion (A): Artificial transmission lines are frequently used in laboratories.
Reason (R): An artificial transmission line can be used to represent an actual line and can also be used as a delay circuit, as attenuator, as filter network etc.

Both A and R are correct and R is correct explanation of A
Both A and R are correct but R is not correct explanation of A
A is correct but R is wrong
A is wrong but R is correct

⇒ Analysis of EM wave in waveguide based on
circuit theory
field theory
optical theory
both (a) and (b)

⇒ Skin effect is more pronounced at high frequencies.
TRUE
FALSE

⇒ If X = - 285.56 and the Pascal write statement used is WRITE (X : 8). Then the print out will appear as
-285.56
-2.85 E + 02
-2.85560 E + 02
-2.8 E + 02

⇒ In the circuit, shown the current I marked is give
2.22 A
1.78 A
4.44 A
0.0833333333333333

Users Also Read
Previous Papers

Aptitude

Reasoning

Gen.Knowledge

Speak English

English / Verbal

Online / Mock Test

Vedic Math