Question is ⇒ Movement of the brake pedal forces brake fluid from the master brake cylinder through brake lines and into the, Options are ⇒ (A) Brake shoes, (B) Wheel cylinders, (C) Brakes cables, (D) Pedal rod, (E) , Leave your comments or Download question paper.

Question is ⇒ Movement of the brake pedal forces brake fluid from the master brake cylinder through brake lines and into the, Options are ⇒ (A) Brake shoes, (B) Wheel cylinders, (C) Brakes cables, (D) Pedal rod, (E) , Leave your comments or Download question paper. Previous question Next question


Q1.	Movement of the brake pedal forces brake fluid from the master brake cylinder through brake lines and into the
A.	Brake shoes [Wrong Answer]
B.	Wheel cylinders [Correct Answer]
C.	Brakes cables [Wrong Answer]
D.	Pedal rod [Wrong Answer]
View Answer 4 -2 Explanation:- Answer : B Discuss it below : !! OOPS Login [Click here] is required to post your answer/result Help other students, write article, leave your comments

Previous question Next question

Also Read Similar Questions Below :

⇒ As compression ratio in an engine goes up, the octane requirements of the fuel
Goes down
Goes up
Stay about the same

⇒ The size of intake valve is
Smaller than that of the exhaust valve
Equal to that of the exhaust valve
Larger than that of the exhaust valve
Not depending upon the size of exhaust valve

⇒ Due to heat of combustion, with increase in temperature the molecules
Move slower
Vaporize
Move faster

⇒ Which type of valve arrangements require the use of rocket arms?
H - head
T - head
I - head
L - head

⇒ One of the major causes of FHP in an engine is
High speed
High volumetric efficiency
Piston-ring friction

⇒ The temperature of the piston will be more at
The piston walls
The crown of the piston
The skirt of the piston
The piston pin

⇒ When the direct acting shock absorber is compressed or telescoped fluid passes through the piston orifices into the upper part of the cylinder and also
Into the dust shield
Out of the dust shield
Into the reservoir
Out of the reservoir

⇒ In the engine there must be relative motion between the piston and the connecting rod
Atmospheric pressure, inertia and torsional vibration
Centrifugal force, inertia and combustion pressure
Inertia, engine speed and centrifugal force

⇒ The ratio between the speed of the camshaft and the speed of the crankshaft is
1:1
1:4
1:2
1:1/4

⇒ Weight can be attached to wheel rim to correct
Wheel alignment
Wheel run out
Wheel balance

⇒ To correct heavy toe contact on ring gear teeth, move the
Ring gear towards pinion
Ring gear away from pinion
Drive pinion out and back lash

⇒ Bleeding of brakes means
Filling the master cylinder with brake oil
Adjusting the brake shoe
Removing air between master cylinder and each wheel unit

⇒ When the plates of battery cell are made larger in size, we get increased ............
Current
Voltage
Cell resistance

⇒ In jeeps we use
Mechanical brakes
Hydraulic brakes
Air brakes

⇒ Movement of the brake pedal forces brake fluid from the master brake cylinder through brake lines and into the
Brake shoes
Wheel cylinders
Brakes cables
Pedal rod

⇒ Vibration damper ..........
controls the torsional vibrations
drives the pulley
dampens the engine speed
reduces the speed of the flywheel

⇒ In the high gear in the transmission, main shaft turns at the same speed as the
Idler shaft
Counter shaft
Clutch shaft

⇒ When an automobile takes a tum to avoid the skidding and over turning
Each wheel will roll independently
Front two wheels will have a common centre during a turning
All the 4 wheels will roll on arcs having a common centre

⇒ During braking the brake shoe is moved outward to press against the
Wheel piston or cylinder
Brake lining
Brake drum or disc
Wheel rim or axle

⇒ The fit of the piston to the cylinder is measured at the
Piston skirt
Piston head
Point of minimum diameter

⇒ Piston displacement is calculated from the
Cylinder diameter and length
Piston length and diameter
Bore and stroke

⇒ Which one of the following is not a trade name of tractor in India
Kirloskar
Escort
Standard
HMT

⇒ As the load on the vehicle increase it demands
Increased braking torque
Decreased braking torque
Same braking torque

⇒ The main advantage of a fluid coupling is
In its low torque capacity at low speeds
Steady state torque characteristic
Due to its ability to slip
Due to its ability to function fluid medium

⇒ The function of a torque converter or fluid converter is similar to that of a
Gear box
Clutch
Shock absorber
Torsion box

⇒ The Ackermann steering layout
Makes for safer driving
Enables the driver to feel ahead position
Gives minimum tyre wear
Reduces load on the kingpins and stub axle

⇒ A humming noise in the differential is often caused by improper tooth contact between the
Drive pinion & ring gear
Axle and side gear
Pinion and side gears

⇒ The power used in overcoming friction in the engine is called
BHP
IHP
FHP

⇒ In a six cylinder engine there is balance of
Primary forces only
Secondary forces only
Both primary and secondary forces

⇒ In the case of brake linings saturants and bonding materials are used to
Facilitate moulding and curing of brake linings
To improve the heat dissipating capacity of linings
To give a constant coefficient of friction up to 800 C
To make the lining material impervious to moisture and oil and to ensure a steady coefficient of friction up to 3000 C