Question is ⇒ Maximum undistorted power output of a transmitter is obtained when its modulation is __________ percent., Options are ⇒ (A) more than 100, (B) 100, (C) less than 100, (D) 50, (E) , Leave your comments or Download question paper.

Question is ⇒ Maximum undistorted power output of a transmitter is obtained when its modulation is __________ percent., Options are ⇒ (A) more than 100, (B) 100, (C) less than 100, (D) 50, (E) , Leave your comments or Download question paper. Previous question Next question


Q1.	Maximum undistorted power output of a transmitter is obtained when its modulation is __________ percent.
A.	more than 100 [Wrong Answer]
B.	100 [Correct Answer]
C.	less than 100 [Wrong Answer]
D.	50 [Wrong Answer]
View Answer 2 -1 Explanation:- Answer : B Discuss it below : !! OOPS Login [Click here] is required to post your answer/result Help other students, write article, leave your comments

Previous question Next question

Also Read Similar Questions Below :

⇒ A Darlington emitter follower circuit is some times used in the output stage of a TTL gate in order to
increase its I_QL
reduce its I_0H
increase its speed of operation
reduce power dissipation

⇒ Transverse magnetic (TM) waves have
magnetic field component H in the direction of propagation
electric field component E in the direction of propagation
magnetic field component H in the direction of propagation and no component of electric field E in this direction
electric field component E in the direction of propagation and no component of magnetic field H in this direction

⇒ A series RLC circuit is supplied from a variable frequency ac source. The resonant frequency is ω₀. The voltage across C is maximum at a frequency
equal to ω₀
slightly less than ω₀
slightly more than ω₀
none of the above

⇒ The gain of an half wavelength antenna is
2.15 dB
10 dB
1.78 dB
100 dB

⇒ Which of the following is a microwave power amplifier?
Gunn diode
Reflex klystron
Magnetron
Travelling wave tube

⇒ A series R, L, C circuit has R = 2Ω, L = 1H, C = 1 μF. It is connected to an ac variable frequency source of peak voltage 10 V. At resonance the power supplied by the source will be
50 Ω
25 Ω
12.5 Ω
6.25 Ω

⇒ Consider the following statements about advantages of phase discriminator over slope detector

Fewer tuned circuits
Greater limiting
Better linearity
Easy alignment

Which of the above are true?
1, 2, 3, 4
2, 3, 4
1, 2, 3
1, 3, 4

⇒ The HV and other voltage supplies for a TV receiver are obtained from IHVT. The full name for this device is
Internal high voltage transformer
Integrated high voltage transformer
Instant high voltage transformer
Interleaved high voltage transformer

⇒ In a circuit the value of resistor is made four times. The noise voltage generated by this resistance will
be doubled
be increased four times
remain the same
become half

⇒ The skip distance is the maximum distance upto which ionospheric reflection is possible.
TRUE
FALSE

⇒ In communication systems the frequency range used for voice is
15 Hz to 150 Hz
30 Hz to 1000 Hz
100 Hz to 1500 Hz
300 Hz to 3800 Hz

⇒ To convert JK flip flop to D flip flop
connect D to both J and K
connect D to J directly and D to K through inverter
connect D to K directly and D to J through inverter
connect D to K and leave J open

⇒ Shift left and shift right operations occur in a calculator.
TRUE
FALSE

⇒ If I = J = K = 13, then in Fortran 1 = 10 - (1 / 10) * 10 + (J / 5) * 4 + K ** (- 2) is equal to
8
7
6
5

⇒ Figure represen
NPN transistor
PNP transistor
Zener diode
Power diode

⇒ The residual resistivity of a binary alloy at 0 K is
sum of residual resistivities of component metals
difference of residual resistivities of component metals
product of residual resistivities of component metals
dependent on the concentration of minor component in the alloy

⇒ Consider the following stateme
1, 2 and 3
1 and 2 only
2 and 3 only
3 and 4 only

⇒ In the given fi
42737
42739
2
1

⇒ In a 3 phase semiconverter, the freewheeling diode comes into operation only if firing angle
is zero
is 60°
is more than 60°
is more than 90°

⇒ Which component is allowed to pass through it by a choke filter?
Dc
Ac
Both dc and ac
Only high frequency ac

⇒ In a P-N-P junction transistor as compared to base region is more heavily doped so that
leakage current is minimized
recombination will be increased in the base region
the flow across the base regional is only because of electrons
the flow across the base region is mainly because of holes

⇒ The symbol in figure is
SUS
SBS
SCS
None of the above

⇒ A chopper is a high efficiency circuit.
TRUE
FALSE

⇒ TRAP is __________ whereas RST 7.5, RST 6.5, RST 5.5 are __________ .
maskable, non-maskable
maskable, maskable
non-maskable, non-maskable
non-maskable, maskable

⇒ In a square law modulator, the carrier frequency should be __________ times than the highest modulating frequency.
1
2
4
3

⇒ Figure shows the self bias circuit for CE amplifier and its equivalent circuit. V_BB and R_B respectively
10 V and 4 k ohm
5 V and 4 k ohm
2 V and 4 k ohm
2 V and 10 k ohm

⇒ An ac network has two sources of the same frequency. The currents in one branch when the sources act independently are 10 ∠30° A and 10 ∠60° A. When both sources act, the current in the branch should be
19.32 ∠45°
15 ∠45°
20 ∠45°
zero

⇒ The current flowing through a pure capacitor is called displacement current.
TRUE
FALSE

⇒ A BJT is said to be operating in saturation region if
both junctions are reverse biased
both junctions are forward biased
base emitter junction is forward biased and base collector junction is reverse biased
base collector junction is forward biased and base emitter junction is reverse biased

⇒ The contents of the commands register are 23 H. Then port C
is an input port
is an output port
is both input as well as output port
none of the above