Question is ⇒ Manganin, an alloy of copper and manganese, is used in, Options are ⇒ (A) Soldering material, (B) Heating elements, (C) Ballast resistors, (D) Standard resistances, (E) , Leave your comments or Download question paper.

Question is ⇒ Manganin, an alloy of copper and manganese, is used in, Options are ⇒ (A) Soldering material, (B) Heating elements, (C) Ballast resistors, (D) Standard resistances, (E) , Leave your comments or Download question paper. Previous question Next question


Q1.	Manganin, an alloy of copper and manganese, is used in
A.	Soldering material [Wrong Answer]
B.	Heating elements [Wrong Answer]
C.	Ballast resistors [Wrong Answer]
D.	Standard resistances [Correct Answer]
View Answer 1 -1 Explanation:- Answer : D Discuss it below : !! OOPS Login [Click here] is required to post your answer/result Help other students, write article, leave your comments

Previous question Next question

Also Read Similar Questions Below :

⇒ ADC 0804 is a
dual slope A/D converter
single slope A/D converter
successive approximation A/D converter
either (a) or (b)

⇒ In an insulated gate FET, the polarity of inversion layer is the same as that of
minority carriers in source
majority carriers in source
charge on gate electrode
minority carriers in drain

⇒ The power input and output in a device are 3650 W and 3385 W with each reading in doubt by ± 10 W. The percentage uncertainty in losses is
± 7.55%
± 3.77%
± 11.32%
± 15.09%

⇒ If Y(s) = 1 + s, the network has
1 Ω resistor and 1 F capacitor in series
1 Ω resistor and 1 F capacitor in parallel
1 Ω resistor and 1 H inductor in series
1 Ω resistor and 1 H inductor in parallel

⇒ In order to rectify sinusoidal signals of millivolt range (< 0.6 V)
bridge rectifier using diodes can be employed
full wave diode rectifier can be used
a diode is to be inserted in the feedback loop of an op-amp
a diode is to be inserted in the I/P of an op-amp

⇒ A number of impulses spaced fron one another form an impulse train.
TRUE
FALSE

⇒ If the poles lie in second quadrant, damping ratio is
1
less than 1
zero
more than 1

⇒ Industrial noise has the frequency range of
1 to 100 Hz
200 to 5000 Hz
above 200 MHz
1 to 600 MHz

⇒ A digital voltmeter has a read out range from 0 to 999 counts. If the full scale reading is 9.999 V, the resolution is
1 V
0.01 V
1 mV
1 μV

⇒ Figure shows the terminals of a transistor in plastic package TO 18. T
terminals 1, 2, 3 are emitter, collector, base respectively
terminals 1, 2, 3 are emitter, base, collector respectively
terminals 1, 2, 3 are base, emitter collector, respectively
terminals 1, 2, 3 are collector, emitter, base respectively

⇒ In the network of the figure is the maximum power is delivered to RL if its valu
16 Ω
40/3 Ω
60 Ω
20 Ω

⇒ The relation between bandwidth B, modulating frequency f_m and frequency deviation Δf for a sinusoidally modulated FM signal is
B = Δf + f_m
B = 2(Δf + f_m)
B = f_m - Δf/
B = 2(f_m - Δf)

⇒ The expression A² + B² - 3 AB when written is Pascal should be written as
A * A + B * B - 3 A * B
A * A + B * B - 3.0 A * B
A * A + B * B - 3.0 * A * B
A * A + B * A - 3 * A * B

⇒ Almost all high level languages have provision for logical operations.
TRUE
FALSE

⇒ For generating 1 MHz frequency signal, the most suitable circuit is
phase shift oscillator
weinbridge oscillator
colpitt's oscillator
clapp oscillator

⇒ The fourier transform of a voltage signal x(t) is X(f). The unit of X(f) is __________ .
volts
volt²
volt/sec
volt-sec

⇒ The pre-emphasis circuit is used
prior to modulation
after demodulation
for low frequency components of the signal
none of the above

⇒ In TV system in India, each frame is divided into
625 horizontal lines
525 horizontal lines
425 horizontal lines
325 horizontal lines

⇒ The current in an RL series circuit is 1 - e^-t amperes. Then di/dt is
1 - e^-t
- e^-t
e^t
e^-2t

⇒ The number of doped regions in PIN diode is
1
2
3
1 or 2

⇒ In which region of a CE bipolar transistor is collector current almost constant?
Saturation region
Active region
Breakdown region
Both saturation and active region

⇒

Assertion (A): Orbital magnetic moment of an electron in an atom is of the order of 1 Bohr magneton.

Reason (R): 1 Bohr magneton = 9.27 x 10^-24 A/m².

Both A and R are true and R is correct explanation of A
Both A and R are true but R is not correct explanation of A
A is true but R is false
A is false but R is true

⇒

Assertion (A): The horizontal intercept of dc load line is the same as ideal cut off point

Reason (R): When a transistor is in cut off region, collector current is zero

Both A and R are correct and R is correct explanation for A
Both A and R are correct but R is not correct explanation for A
A is correct R is wrong
A is wrong R is correct

⇒ How many interrupts are there of 8085 μP?
4
5
6
8

⇒ If number of information bits is 4, the parity bits in Hamming code are located at bit positions __________ from the LSB.
1, 2, 5
1, 2, 4
1, 2, 3
1, 2

⇒ Which of the following element does not have three valence electrons?
Boron
Aluminium
Gallium
Phosphorus

⇒ Magnetic susceptibility of a medium is the ratio of
magnetic field strength to mmf
intensity of magnetization to magnetic flux density
intensity of magnetization to field strength
mmf to magnetic field strength

⇒ As the number SWG increases, area of cross-section decreases.
TRUE
FALSE

⇒ Above ferroelectric curie temperature, spontaneous polarization in ferroelectric materials becomes stronger.
TRUE
FALSE

⇒ In measuring resistance using voltmeter and ammeter, the resistances of voltmeter and ammeter also affect the accuracy of measurement.
TRUE
FALSE