Question is ⇒ Magnetic susceptibility of a medium is the ratio of, Options are ⇒ (A) magnetic field strength to mmf, (B) intensity of magnetization to magnetic flux density, (C) intensity of magnetization to field strength, (D) mmf to magnetic field strength, (E) , Leave your comments or Download question paper.

Question is ⇒ Magnetic susceptibility of a medium is the ratio of, Options are ⇒ (A) magnetic field strength to mmf, (B) intensity of magnetization to magnetic flux density, (C) intensity of magnetization to field strength, (D) mmf to magnetic field strength, (E) , Leave your comments or Download question paper. Previous question Next question


Q1.	Magnetic susceptibility of a medium is the ratio of
A.	magnetic field strength to mmf [Wrong Answer]
B.	intensity of magnetization to magnetic flux density [Wrong Answer]
C.	intensity of magnetization to field strength [Correct Answer]
D.	mmf to magnetic field strength [Wrong Answer]
View Answer 3 -1 Explanation:- Answer : C Discuss it below : !! OOPS Login [Click here] is required to post your answer/result Help other students, write article, leave your comments

Previous question Next question

Also Read Similar Questions Below :

⇒ To ensure that only dominant TE₁₀ mode propagates in a rectangular waveguide, the operating frequency
must be more than cutoff frequency of TE₁₀ mode
must be less than cutoff frequency of TE₂₀ mode
must be more than cutoff frequency of TE₁₀ mode and less than cutoff frequency of TE₂₀ mode
must be less than cutoff frequency of TE₁₀ mode

⇒ Chrome signals in PAL colour television system consist of
R - Y and B - Y signal
V and U signals
I and Q signals
R - Y and G - Y signals

⇒ To measure a resistance of about 8 ohms we should use
Kelvin's double bridge
Wheatstone bridge
Meggar
Either (b) or (c)

⇒ In a cycloconverter it is possible to vary
only output frequency
only output voltage
both output voltage and frequency but not simultaneously
both output voltage and output frequency simultaneously

⇒ For TM waves in a parallel plate waveguide, the minimum attenuation arising from imperfect conductors would occur at a freq. of (f_c is the cut off frequency)
3 f_c
3 f_c
2 f_c
2 f_c

⇒ Laplace transform of a unit doublet U_-2 (t) is
1/s
s
0
1

⇒ In 8085 the pins for + 5 V input and ground are
20 and 40 respectively
40 and 20 respectively
1 and 2 respectively
1 and 1 respectively

⇒ Given that the band gap of cadmium sulphide is 2.5 eV, the maximum photon wavelength, for e^--hole pair generation will be
5400 mm
540 mm
5400 Å
540 Å

⇒ In CE configuration, the output characteristics of a bipolar junction transistor is drawn between
I_C and V_CB
I_E and V_CB
I_C and V_CE
I_E and V_CE

⇒ The function off an oxide layer in an IC device is to

mask against diffusion or ion implantation
insulate the surface electrically
increase the melting point of Si
produce a chemically stable protective layer

1, 2, 3
1, 3, 4
2, 3, 4
4, 1, 2

⇒

Match the following:

	List I		List II
A.	Zener diode	1.	used in seven segment display
B.	Tunnel diode	2.	used in voltage regulator circuits
C.	LED	3.	used is solar energy utilization
D.	Photovoltaic cell	4.	used in digital circuits

A-1, B-3, C-2, D-4
A-2, B-3, C-1, D-4
A-2, B-4, C-1, D-3
A-3, B-2, C-4, D-1

⇒ A sinusoidal signal with peak to peak amplitude of 1.536 volt is quantized into 128 levels using a mid-rise uniform quantizer. The quantization noise power is
0.768 V
48 x 10^-6 V
12 x 10^-6 V
3.072 Volt

⇒ The current through a 1 mH inductance is i(t) = 2.56 x 10^-2 - 4 x 10³ t for 2 ≤ t ≤ 20 μ sec. The voltage across the inductor is
4
8
0
8 x 10³

⇒ In the circuit of figure the current through 5 Ω resistance at t = 0^{+0.166666666666667
2.5 A
3.1 A
0}

⇒ Which of the following circuit would be preferred for a 355 KHz IF amplifier?
Resistance loaded
Double tuned transformer
Video amplifier
Class C

⇒ The carrier mobility in a semiconductor is 0.4 m²/Vs. Its diffusion constant at 300 K will be (in m²/s)
0.4
0.16
0.04
0.01

⇒ A Schottky diode has
no minority carriers and very low voltage drop in forward direction
no minority carriers and very high voltage drop in forward direction
large number of minority carriers and very high voltage drop in forward direction
large number of minority carriers and very low voltage drop in forward direction

⇒ For low impedance SAW filter the most suitable material for substrate of SAW filter is
PZT ceramics
ZnO
Lithium titanate
Lithium neobate

⇒ In the network shown in figure, the voltage drops across R₂ and R₃ are 10 V and 16 V with polarities as shown. The current in R_{1is 9 A and directed towards node 0
is 9 A and directed away from node 0
is 9 A but directed of current cannot be found
is impossible to be found}

⇒ A collector collects
electrons from the base in case of N-P-N transistor
electrons from the emitter in case P-N-P transistor
holes from the base in case of N-P-N transistor
holes from the base in case of P-N-P transistor

⇒ An SR flip flop can be built using NOR gates or NAND gates.
TRUE
FALSE

⇒ Tracking of extra terrestrial objects requires
high transmitting power
very sensitive receiver
fully steerable antenna
all of the above

⇒

Assertion (A): Decoder is not a combinational circuit.

Reason (R): Every memory element of semi conductor form has a decoder.

Both A and R are correct and R is correct explanation of A
Both A and R are correct but R is not correct explanation of A
A is true, R is false
A is false, R is true

⇒ A sequence detector is required to give a logical output of 1 whenever the sequence 1011 is detected in the incoming pulse stream. Minimum number of flip-flops needed to built the sequence detector is
4
3
1
2

⇒ In which one of the following types of analog to digital convertors the conversion time is practically independent of the amplitude of the analog signal?
The dual slope integrating type
Successive approximation type
Counter ramp type
Tracking type

⇒ For holding the drain current constant in spite of large changes in JFET parameters
current source bias is used
voltage divider bias is used
reverse bias is used
no bias is used

⇒ A permanent magnet moving coil meter can be used as
ac only
dc only
both ac and dc
low frequency ac and dc

⇒ 4 bit ripple counter and 4 bit synchronous counter are made using flip-flop having a propagation delay of 10 ns each. If the worst case delay in the ripple counter and the synchronous counter be R and S respectively, then
R = 10 ns, S = 40 ns
R = 40 ns, S = 10 ns
R = 10 ns, S = 30 ns
R = 30 ns, S = 10 ns

⇒ Divergence of curl A is
∇ . (∇ x A) = 1
∇ . (∇ x A) = 0
∇ . (∇ x A) = ∇
∇ . (∇ x A) = - ∞

⇒ The energy of highest value of Autocorrelation of a function 100 cos 50 pt is
50
10
200
zero