Question is ⇒ Low tension cables are generally used upto, Options are ⇒ (A) 200 V, (B) 500 V, (C) 700 V, (D) 1000 V, (E) , Leave your comments or Download question paper.

Question is ⇒ Low tension cables are generally used upto, Options are ⇒ (A) 200 V, (B) 500 V, (C) 700 V, (D) 1000 V, (E) , Leave your comments or Download question paper. Previous question Next question


Q1.	Low tension cables are generally used upto
A.	200 V [Wrong Answer]
B.	500 V [Wrong Answer]
C.	700 V [Wrong Answer]
D.	1000 V [Correct Answer]
View Answer 10 -7 Explanation:- Answer : D Discuss it below : !! OOPS Login [Click here] is required to post your answer/result Help other students, write article, leave your comments

Previous question Next question

Also Read Similar Questions Below :

⇒ The electrostatic stress in underground cables is
same at the conductor and the sheath
minimum at the conductor and maximum at the sheath
maximum at the conductor and minimum at the sheath
zero at, the conductor as well as on the sheath

⇒ In single core cables armouring is not done to
avoid excessive sheath losses
make it flexible
either of the above
none of the above

⇒ The advantage of oil filled cables is
more perfect impregnation
smaller overall size
no ionisation, oxidation and formation of voids
all of the above

⇒ The advantage of cables over overhead transmission lines is
easy maintenance
low cost
can be used in congested areas
can be used in high voltage circuits

⇒ In cables the charging current
lags the voltage by 90°
leads the voltage by 90°
lags the voltage by 180°
leads the voltage by 180°

⇒ The thickness of metallic shielding on cables is usually
0.04 mm
0.2 to 0.4 mm
3 to 5 mm
40 to 60 mm

⇒ In the cables, the location of fault is usually found out by comparing
the resistance of the conductor
the inductance of conductors
the capacitances of insulated conductors
all above parameters

⇒ The insulating material for cables should
be acid proof
be non-inflammable
be non-hygroscopic
have all above properties

⇒ If a power cable and a communication cable are to run parallel the minimum distance between the two, to avoid interference, should be
2 cm
10 cm
50 cm
400 cm

⇒ The thickness of the layer of insulation on the conductor, in cables, depends upon
reactive power
power factor
voltage
current carrying capacity

⇒ Which of the following protects a cable against mechanical injury ?
Bedding
Sheath
Armouring
None of the above

⇒ Dielectric strength of rubber is around
5 kV/mm
15 kV/mm
30 kV/mm
200 kV/man

⇒ In a cable, the maximum stress under operating conditions is at
insulation layer
sheath
armour
conductor surface

⇒ Pressure cables are generally not used beyond
11 kV
33 kV
66 kV
132 kV

⇒ The material for armouring on cable is usually
steel tape
galvanised steel wire
any of the above
none of the above

⇒ The current carrying capacity of cables in D.C. is more than that in A.C. mainly due to
absence of harmonics
non-existence of any stability limit
smaller dielectric loss
absence of ripples

⇒ The bedding on a cable consists of
hessian cloth
jute
any of the above
none of the above

⇒ In a cable the voltage stress is maximum at
sheath
insulator
surface of the conductor
core of the conductor

⇒ Cables for 220 kV lines are invariably
mica insulated
paper insulated
compressed oil or compressed gas insulated
rubber insulated

⇒ In capacitance grading of cables we use a ____ dielectric.
composite
porous
homogeneous
hygroscopic

⇒ Conduit pipes are normally used to protect ____ cables.
unsheathed cables
armoured
PVC sheathed cables
all of the above

⇒ The disadvantage with paper as insulating material is
it is hygroscopic
it has high capacitance
it is an organic material
none of the above

⇒ PVC stands for
polyvinyl chloride
post varnish conductor
pressed and varnished cloth
positive voltage conductor

⇒ If a cable of homogeneous insulation has a maximum stress of 10 kV/mm, then the dielectric strength of insulation should be
5 kV/mm
10 kV/mm
15 kV/mm
30 kV/mm

⇒ Solid type cables are considered unreliable beyond 66 kV because
insulation may melt due to higher temperature
of corona loss between conductor and sheath material
there is a danger of breakdown of insulation due to the presence of voids

⇒ The insulating material for a cable should have
low cost
high dielectric strength
high mechanical strength
all of the above

⇒ Low tension cables are generally used upto
200 V
500 V
700 V
1000 V

⇒ If the length of a cable is doubled, its capacitance
becomes one-fourth
becomes one-half
becomes double
remains unchanged

⇒ The insulation of the cable decreases with
the increase in length of the insulation
the decrease in the length of the insulation
either (a) or (b)
none of the above

⇒ The minimum dielectric stress in a cable is at
armour
bedding
conductor surface
lead sheath