Question is ⇒ Light dependent resistors are, Options are ⇒ (A) highly doped semiconductor, (B) intrinsic semiconductor, (C) lightly doped semiconductor, (D) either (a) or (c), (E) , Leave your comments or Download question paper.

Question is ⇒ Light dependent resistors are, Options are ⇒ (A) highly doped semiconductor, (B) intrinsic semiconductor, (C) lightly doped semiconductor, (D) either (a) or (c), (E) , Leave your comments or Download question paper. Previous question Next question


Q1.	Light dependent resistors are
A.	highly doped semiconductor [Wrong Answer]
B.	intrinsic semiconductor [Wrong Answer]
C.	lightly doped semiconductor [Correct Answer]
D.	either (a) or (c) [Wrong Answer]
View Answer 1 -1 Explanation:- Answer : C Discuss it below : !! OOPS Login [Click here] is required to post your answer/result Help other students, write article, leave your comments

Previous question Next question

Also Read Similar Questions Below :

⇒ In an ac network the sum of currents entering a node is 10 ∠45°. The sum of currents leaving the node is
19.32 ∠45°
15 ∠45°
20 ∠45°
zero

⇒ Isotropic radiator is one that radiates energy
uniformly in all direction
inside a hollow sphere
in a well defined isotropic direction
none of the above

⇒ In the CMOS inverter
one transistor is N channel and the other P channel
one is enhancement type and other depletion type
both are N channel with one enhancement and the other depletion type
none

⇒ The resistance of human body is about
5000 Ω
2000 Ω
1000 Ω
200 Ω

⇒ In modern MOSFET_S, the material used for the gate is
high purity silicon
high purity silica
heavily doped polycrystalline silicon
epitaxial grown silicon

⇒ In AM, if modulation index is more than 100%, then
bandwidth increases
the wave gets distorted
power of the wave increases
efficiency of transmission increases

⇒ A matched generator (Z_g = Z₀) with 1 Ω available. If all ports are matched, the power delivered at ports 1, 2, 3 respectively are
0.5 W, 0.5 W, 0 W
0 W, 0 W, 1 W
0.33 W each
0 W, 0.25 W, 0.25 W

⇒ A directional coupler is used
to transmit microwave signals
to generate microwave signals
to measure amplitude and phase of a travelling wave
both (a) and (b)

⇒ The logical expression Y = A + AB is equivalent to
Y = AB
Y = AB
Y = A + B
Y = A + B

⇒ To separate channels in FDM receiver we have to use
integration
AND gate
band pass filter
differentiation

⇒ The internal structure of PL A is similar to
RAM
ROM
both RAM and ROM
neither RAM nor ROM

⇒ In microstrip line has dielectric material most commonly used is
silicon
rubber
plastic
bakelite

⇒ In feedback amplifier the closed loop gain is nearly independent of open loop gain and depends only on the feedback factor.
TRUE
FALSE

⇒ The signal m(t) = 10 cos 100 pt is sampled at the rate of F_s = 75 H_z, then determine signal after sampling.
4 cos 100 pt + 8 sin 200 pt
4 cos 100 pt + 8 sin 200 pt + cos 75 pt
4 cos 25 pt + 8 sin 50 pt + cos 75 pt
none

⇒ In all metals
conductivity decreases with increase in temperature
current flow by electrons as well as by holes
resistivity decreases with increase in temperature
the gap between valence and conduction bands is small

⇒ The sum of positive real function is positive real.
TRUE
FALSE

⇒ Transfer functions of even complicated components can be found by frequency response tests.
TRUE
FALSE

⇒ In a conductor which of the following relations hold good?
∇ x D = r
∇ . D = r
∇ x D = 0
∇ . D = 0

⇒ In a single phase full wave regulator, the firing angles in the positive and negative half cycles are generally
equal
different
equal or different
different but sometimes equal

⇒ The electrolyte in nickel cadmium cell is dilute potassium hydroxide.
TRUE
FALSE

⇒

Assertion (A): It is possible that a digital circuit gives the same output for different input voltages

Reason (R): A digital circuit is also called logic circuit.

Both A and R are correct and R is correct explanation of A
Both A and R are correct but R is not correct explanation of A
A is true, R is false
A is false, R is true

⇒ For F₁ layer the maximum ionic density is 2.3 x 10⁴ electrons per cc. The critical frequency for this layer will be
1.36 MHz
13.6 MHz
136 MHz
1360 MHz

⇒

Assertion (A): In the circuit shown figure the diode is used to protect the active devices. Transistor T goes into saturation when a positive pulse is applied at base and non conducting

Reason (R): When the current in an inductor is suddenly stopped, a high voltage is induced across
Both A and R are correct and R is correct explanation for A
Both A and R are correct but R is not correct explanation for A
A is correct R is wrong
A is wrong R is correct

⇒ Antenna used for direction finding is
long dipole
parabolic
rhombic
helical

⇒ Free electrons exist in
first band
second band
third band
conduction band

⇒ Fourier transform is defined for
periodic
non-periodic
finite duration
all

⇒ It is known that noise phase modulates the FM wave. As the noise side band frequency approaches the carrier frequency, the noise amplitude
will increase
will decrease
will remain constant
will reduce to negligible value

⇒ The circuit given bel
Circuit is band stop with two edge frequency of 39.7875 Hz to 1592 Hz
Circuit is band pass with two edge frequency of 39.7875 Hz to 1592 Hz
Circuit is oscillator, oscillation at two frequencies 39.7875 Hz to 1592 Hz depending on R₃, R₄, R₅ and R₆
None of these

⇒ The effect of lead resistance is important in measurement of
resistance of shunt
resistance of shunt winding
resistance of ammeter
both (a) and (c)

⇒ If reference sound pressure P₀ is 2 x 10^-5 N/m², a sound pressure of 90 dB is equal to
0.632 N/m²
0.707 N/m²
0.835 N/m²
0.925 N/m²