Question is ⇒ Leaf spring for vehicles are nipped to, Options are ⇒ (A) To vary the effective length of the spring, (B) To increase the interleaf friction, (C) Improve the load carrying capacity of spring, (D) Ensure that all leaves are uniformly stressed during loading, (E) , Leave your comments or Download question paper.

Question is ⇒ Leaf spring for vehicles are nipped to, Options are ⇒ (A) To vary the effective length of the spring, (B) To increase the interleaf friction, (C) Improve the load carrying capacity of spring, (D) Ensure that all leaves are uniformly stressed during loading, (E) , Leave your comments or Download question paper. Previous question Next question


Q1.	Leaf spring for vehicles are nipped to
A.	To vary the effective length of the spring [Wrong Answer]
B.	To increase the interleaf friction [Wrong Answer]
C.	Improve the load carrying capacity of spring [Wrong Answer]
D.	Ensure that all leaves are uniformly stressed during loading [Correct Answer]
View Answer 6 -2 Explanation:- Answer : D Discuss it below : !! OOPS Login [Click here] is required to post your answer/result Help other students, write article, leave your comments

Previous question Next question

Also Read Similar Questions Below :

⇒ Brake efficiency is a term which denotes
Efficiency of the braking system as a whole
Efficiency of the braking linings
The deceleration as percentage of gravity
Efficiency of the operating linkage

⇒ The compression ratio in a diesel engine is as high as
25:1
20:1
10:1
5:1

⇒ Of the four tyres on a car, the one that wears most is the
Right front tyre
Right rear tyre
Left front tyre
Left rear tyre

⇒ When we lift a 10 kg weight, 3 metre we would be doing
300 m kg of work
3 m kg of work
30 m kg of work

⇒ The combustion process in a diesel engine is
Constant pressure process
Isothermal process
Constant volume process
Adiabatic process

⇒ In the differential the ring gear is bolted to the
Differential housing
Differential case
Axle housing
Drive pinion

⇒ If the differential noise is present only when the car is rounding a curve the trouble would be due to
Heavy heel contact on gear teeth
Heavy toe contact on gear teeth
Binding in differential case

⇒ The hydrodynamic torque converter
Gives a continuous variation of torque with increase of output speed
Enables to get the max. h.p continuously
Gives a speed variation without torque variation
Maintains a high efficiency throughout the operating speed range

⇒ The function of the relay valve in a compressed air brake system is to
Limit the maximum pressure reached in brake chambers
Relieve air pressure in brake chambers when it reaches a maximum value
Reduce the effort required at the brake pedal
Speed up the supply of air to brake chambers located at a distance from brake valve

⇒ The material used for the piston of modern passenger cars are
Brass pistons
Cast iron pistons
Aluminiun alloy pistons
Steel pistons

⇒ When air is heated, it
Contracts and becomes heavier
Expands and becomes heavier
Expands and becomes lighter

⇒ A double acting shock absorber usually has
Unequal pressure acting on either sides
Equal pressure on either side
Pressure acting only on one side

⇒ The number of parallel paths in a lap winding of the armature of a DC generator is equal to
Half the number of poles
Number of poles
Two

⇒ The power used in overcoming friction in the engine is called
BHP
IHP
FHP

⇒ Parts of the clutch that should not be cleaned in solvent include the
Friction disc and throw out bearing
Friction disc cover
Throw out bearing and springs
Release levers and springs

⇒ The main advantage of a fluid coupling is
In its low torque capacity at low speeds
Steady state torque characteristic
Due to its ability to slip
Due to its ability to function fluid medium

⇒ Clutch noises are usually most noticeable when the engine is
Being started
Decelerating
Idling
Accelerating

⇒ As the number of cylinders in multi cylinder engines increases the power to weight ratio .........
Remains the same
Increases
Becomes zero
Decreases

⇒ Piston compression rings are manufactured by
Aluminium
Cast iron
Steel
Bronze

⇒ In commercial vehicle layouts engine is located forward, rear or under floor mainly to
Better utilization of space
Increase fuel economy
Better weight distribution
Reduce the weight of chassis

⇒ Due to heat of combustion, with increase in temperature the molecules
Move slower
Vaporize
Move faster

⇒ There is a double faced friction disc splined to a shaft in the
Transmission
Differential
Engine
Clutch

⇒ Engine torque is highest at
High speed
Low speed
Intermediate speed

⇒ If the connecting rod longer, the side thrust of the piston is
Increased
Constant
Decreased

⇒ Engine torque is highest at
Low speed
Intermediate speed
High speed

⇒ Braking is produced by the frictional effect between the brake drum and the
Wheel studs
Wheel rim
Brake shoes
Wheel cylinder pistons

⇒ The axle shaft of a semi floating rear axle is subjected to
Axial thrust only
Axial thrust and bending stress
Torsional stress only
Bending, torsional stresses and end thrust

⇒ The type of rear axle in which the wheel end is supported by bearings inside the axle housing is
Semi floating axle
Three-quarter floating axle
Full-floating axle

⇒ The friction disc is positioned between the flywheel and the
Engine
Crankshaft
Pressure plate

⇒ Synchromesh devices in the transmission synchronize the gears about to be
Meshed
De-meshed
Stopped