Question is ⇒ Joining of thin foils is preferred to be done by, Options are ⇒ (A) gamma rays, (B) X-rays, (C) microwaves, (D) gas welding, (E) , Leave your comments or Download question paper.

Question is ⇒ Joining of thin foils is preferred to be done by, Options are ⇒ (A) gamma rays, (B) X-rays, (C) microwaves, (D) gas welding, (E) , Leave your comments or Download question paper. Previous question Next question


Q1.	Joining of thin foils is preferred to be done by
A.	gamma rays [Wrong Answer]
B.	X-rays [Wrong Answer]
C.	microwaves [Correct Answer]
D.	gas welding [Wrong Answer]
View Answer 9 -4 Explanation:- Answer : C Discuss it below : !! OOPS Login [Click here] is required to post your answer/result Help other students, write article, leave your comments

Previous question Next question

Also Read Similar Questions Below :

⇒ Larger length & diameter water pipes are made by
electrical resistance welding.
die casting.
semi-centrifugal casting.
continuous casting.

⇒ Ageing of steel refers to the
degradation of steel by corrosion.
failure of steel structure by overstress-ing.
return of sharp yield point in temper rolled low carbon sheet after a period of time.
decarburisation of steel by overheating.

⇒ Methyl orange indicator turns
orange yellow in alkaline medium.
orange yellow in acidic medium.
colourless in acidic medium.
colourless in basic medium.

⇒ Dryness fraction of dry steam is
0
∞
1
0.5

⇒ Source of heat supply in a cupola is
coke
charcoal
lumpy coal
pulverised coal

⇒ Which of the following varies as the square root of oil pressure during atomisation of fuel oil through a pressure jet burner ?
Output & fineness
Velocity
Both (a) & (b)
None of these

⇒ Tesla metre per ampere (T. m/A) is the unit for the measurement of
magnetic succeptibility.
magnetic moment.
permeability of free space.
flux density.

⇒ All modes of heat transfer i.e., conduction, convection & radiation occur in case of the
condensation of steam in a partial condenser.
boiler furnace.
insulated pipe car raying high pressure steam.
none of these.

⇒ In __________ process, ions of salts react with water to produce acidity or alkalinity.
hydration
hydrolysis
electrolysis
dialysis

⇒ Alloys having more than 80% copper are generally more
abrasion resistant.
corrosion resistant.
prone to season cracking.
machinable.

⇒ Which set of materials is used as a moderator in nuclear reactor ?
Zircalloy & berrylium.
Zircalloy & heavy water.
Zirconium & berrylium.
Heavy water & berrelium.

⇒ The critical pressure at which the latent heat of vaporisation of steam becomes zero is __________ Kg/cm² .
273.15
225.65
100.03
373.15

⇒ Pressure exerted by a liquid depends upon its
surface tension
density
viscosity
buoyancy

⇒ Ceramic tips for the cutting tool are prepared from __________ powder.
carbon
silicon carbide
aluminium oxide
tungsten

⇒ Fire on fuel oil lines can be extinguished by
foam
steam
water
carbon dioxide

⇒ Unit of surface tension in S.I. unit is
Watt/m
Joule/m²
Newton/m²
Joule/m

⇒ The materials which fracture even at small strains are termed as brittle, while those materials which exhibit an appreciable deformation before failure are termed as
rigid
tough
ductile
plastic

⇒ Two wires of the same radius & material having length in the ratio of 1 : 2 are stretched by the same force. The strain produced in the two wires will be in the ratio of
0.0423611111111111
0.0430555555555556
0.0840277777777778
0.0444444444444444

⇒ Co-efficient of performance of a Carnot cycle refrigerator operating between - 23°C and + 27°C is
3
5
0.5
1.5

⇒ The weight of a body at the centre of the earth is
infinite.
zero.
same as on the surface of the earth.
none of these.

⇒ __________ the exhaust gas is an indication of the incomplete combustion of fuel.
Low temperature of
High temperature of
High % of CO in
High % of CO₂ in

⇒ Which of the following heat treatment processes is usually applied to castings ?
Tempering
Annealing
Normalising
Carburising

⇒ Carbon supply in pack carburising process is in the form of
charcoal
calcium carbide
hydrocarbon oil
graphite

⇒ An orthotropic material is a special class of anisotropic material, which is described by their properties in three perpendicular directions. An example of orthotropic material is
stainless steel
cast iron
wood
teflon

⇒ Cold working of a material results in increase in hardness, which is termed as the __________ hardening.
cold
work
age
induction

⇒ Unit molar solution of __________ is the best conductor of electricity.
sodium chloride
acetic acid
sulphuric acid
sucrose

⇒ If the head is doubled in & centrifugal pump, the power required will increase in the ratio of
2³
2^3/2
2^5/2
2^1/3

⇒ The standard instrument used for calibrating the load applied by universal testing machine is called
extensometer
spring balace
dynamometer
none of these

⇒ Brittleness induced due to the presence of sulphur in steel can be reduced by adding
manganese
magnesium
vanadium
copper

⇒ Filler metal is not used in the __________ welding.
seam
electric spot
projection
all a, b & c