Question is ⇒ It is required to measure a low magnitude high frequency current. The proper instrument is, Options are ⇒ (A) moving iron, (B) dynamometer, (C) thermocouple, (D) induction, (E) , Leave your comments or Download question paper.

Question is ⇒ It is required to measure a low magnitude high frequency current. The proper instrument is, Options are ⇒ (A) moving iron, (B) dynamometer, (C) thermocouple, (D) induction, (E) , Leave your comments or Download question paper. Previous question Next question


Q1.	It is required to measure a low magnitude high frequency current. The proper instrument is
A.	moving iron [Wrong Answer]
B.	dynamometer [Wrong Answer]
C.	thermocouple [Correct Answer]
D.	induction [Wrong Answer]
View Answer 2 -1 Explanation:- Answer : C Discuss it below : !! OOPS Login [Click here] is required to post your answer/result Help other students, write article, leave your comments

Previous question Next question

Also Read Similar Questions Below :

⇒ A current of 1 A in the coil of an iron cored electromagnet cause a flux density of 0.2.T. If the current is 2 A, B=
0.2 T
0.4 T
0.4 T or less
0.4 T or more

⇒ In figure, V_CC = + 30 V, R₁ = 200 kΩ and R₂ = 100 kΩ. If V_BE = 0.7 V, the voltage a cross R_{E+20 V
+19.3 V
+10 V
+9.3 V}

⇒ A dielectric should have poor heat conductivity.
TRUE
FALSE

⇒ For a binary half subtractor having two inputs A and B the correct sets of logical expressions for the outputs D (A - B) and X = Borrow are
D = AB + AB, X = AB
D = AB AB, X = AB
D = AB + AB, X = AB
D = AB + A B, X = AB

⇒ As compared to MOS memories, bipolar memories have
slower access time but are cheaper
slower access time and are costly
faster access time and are cheaper
faster access time and are costly

⇒ In each of circuits below, indicate which diode is conduct
Figure A
Figure B
Figure C
All the three

⇒ Which of these has the highest dielectric strength?
Mica
Air
Cotton
Rubber

⇒ In the given figure shows a 4 bit serial in parallel out right shift register. The initial contents as shown are 0110. After 3 clock pulses the contents wil
0
101
1010
1111

⇒ A capacitor used for power factor correction is single phase circuit decreases
power factor
line current
both line current and p.f.
the line current and increases p.f.

⇒ The enhancement type MOSFET is called a
normally on MOSFET
normally off MOSFET
P-type MOSFET
N-type MOSFET

⇒

Match the following:

	List I (Transducer)		List II (Operation)
A.	Bourden tube	1.	Fluid flow to resistance change
B.	Hot wire ammeter	2.	Velocity to pressure
C.	Hydrometer	3.	Pressure to displacement
D.	Pitot tube	4.	Specific gravity to displacement

A-1, B-3, C-2, D-4
A-3, B-1, C-2, D-4
A-3, B-1, C-4, D-2
A-4, B-2, C-3, D-1

⇒ For a D/A converter, inputs and outputs are given. The output corresponding to digital input 01
2.0 V
2.5 V
3.0 V
4.0 V

⇒ A 2 bit BCD D/A converter is a weighted resistor type with E_R = 1V, R = 1 MΩ and R_f = 10KΩ then Resolution in percent and volt is __________ .
1%, 1 mv
10%, 10 mv
10%, 1 mv
1%, 10 mv

⇒ The circuit show in the figure has 4 boxes each described by inputs P, Q, R and outputs y, z
4 bit adder giving P + Q
4 bit subtractor P - Q
4 bit subtractor Q - P
4 bit adder P + Q + R

⇒ In a 4 input OR gate, the total number of High outputs for the 16 input states are
16
15
14
13

⇒ The main purpose of using transformer coupling in a class A amplifier is to make it more
efficient
less costly
less bulky
distortion free

⇒ The gate-source voltage that reduces the drain current to approximately zero is called
gate-source on voltage
gate-source voltage
pinch-off voltage
gate-source cut-off voltage

⇒ If temperature is increased, the temperature coefficient of a metal
increases
decreases
may increase or decrease
remains constant

⇒ A second-order band-pass active filter can be obtained by cascading a low pass second order section having cut off frequency f_OH with a high pass second order section having cut-off frequency f_OL provided
f_OH > f_OL
f_OH < f_OL
f_OH = f_OL
f_OH ≤ 1/2f_OL

⇒ The instrument used to check insulation of household wiring is
megger
ohmmeter
multimeter
high resistance voltmeter

⇒ A perfect conductor is a perfect absorber of electromagnetic waves.
TRUE
FALSE

⇒ A three stage telephone switching structure is to have 128 input and 128 output terminals. It has been found that at peak time the utilization probability is 0.1. The number of intermediate links required for non-blocking configuration is 15. If the actual number of intermediate links is 5, the probability of blocking of call is
0.01
0.005
0.002
0.001

⇒ A sine wave is passed through an amplifier which severely limits it symmetrically. If then passes to a second amplifier which is narrow band and tuned to the frequency of the original sine wave. What will be the output wave from this second amplifier?
A square wave of the same frequency as that of the original sine wave
A square wave of double the frequency of that of original sine wave
A sine wave of constant amplitude at the frequency of the original sine wave
A sine wave of constant amplitude at double frequency of the original sine wave

⇒ State space analysis is applicable to
time invariant systems
time varying systems
both time invariant and time varying systems
none of the above

⇒ ∈_r is determined by the atomic structure of the dielectric.
TRUE
FALSE

⇒ The hexadecimal number system is
widely used in analyzing and programming microprocessors
an obsolete system no more in use
used in calculators only
none of the above

⇒ The units for electric dipole moment are
coulombs
colomb-metre
coulomb/metre
coulomb/m²

⇒ X(t) is a stationary process with the power spectral density S_x(f) > 0 for all f. The process is passed through a system shown be
S_y(f) > 0 for all f
S_y(f) = 0 for |f| > 1kHz
S_y(f) = 0 for f = nf₀, f₀ = 2kHz, n any integer
S_y(f) = 0 for f = (2n + 1)f₀ = 1 kHz, n any integer

⇒ A thyristor has internal power dissipation of 40W and is operated at an ambient temperature of 20°C. If thermal resistance is 1.6° C/W, the junction temperature is
114°C
164°C
94° C
84° C

⇒ Find E at P(1, 1, 1) caused by four identical 3 nC point charges located at P₁(1, 1, 0), P₂(- 1, 1, 0), P₃(- 1, - 1, 0) P₄(1, - 1, 0)
21.58a_x + 21.58a_y + 12a_z V/m
6.82a_x + 6.82a_y + 32.89a_z V/m
-6.82a_x - 6.82a_y - 32.89a_z V/m
-21.58a_x - 21.58a_y - 12az V/m