Question is ⇒ Inputs A and B of the given figure are applied to a NAND gate. The output is, Options are ⇒ (A) from 0 to 6, (B) from 0 to 2, (C) from 0 to 1 and 2 to 3, (D) from 1 to 2 and 3 to 4, (E) , Leave your comments or Download question paper.

Question is ⇒ Inputs A and B of the given figure are applied to a NAND gate. The output is, Options are ⇒ (A) from 0 to 6, (B) from 0 to 2, (C) from 0 to 1 and 2 to 3, (D) from 1 to 2 and 3 to 4, (E) , Leave your comments or Download question paper. Previous question Next question


Q1.	Inputs A and B of the given figure are applied to a NAND gate. The output is
A.	from 0 to 6 [Wrong Answer]
B.	from 0 to 2 [Wrong Answer]
C.	from 0 to 1 and 2 to 3 [Correct Answer]
D.	from 1 to 2 and 3 to 4 [Wrong Answer]
View Answer 2 -1 Explanation:- Answer : C Discuss it below : !! OOPS Login [Click here] is required to post your answer/result Help other students, write article, leave your comments

Previous question Next question

Also Read Similar Questions Below :

⇒ In a 3 phase semiconverter, the freewheeling diode comes into operation only if firing angle
is zero
is 60°
is more than 60°
is more than 90°

⇒

Assertion (A): CCIR-B system has 625 scanning lines per frame and 2 : 1 interlace.

Reason (R): The aspect ratio is 4 : 3

Both A and R are correct and R is correct explanation of A
Both A and R are correct but R is not correct explanation of A
A is correct but R is wrong
A is wrong but R is correct

⇒ Consider the following statements regarding sources or error in a Q-meter:

If a coil with resistance R is connected in direct measurement mode and if the residual resistance of Q-meter is 0.1 R, then the measure Q of the coil would be 1.1 times the actual Q.
If the inductance to be measured is less than 0.1 mH, the error due to presence of residual inductance cannot be neglected.
The presence of distributed capacitance in a coil modifies the effective Q of the coil.

Which of the above statements are correct?
1, 2 and 3
1 and 2 only
2 and 3 only
1 and 3 only

⇒ Full duplex operation-permits transmission in both directions at the same time.
TRUE
FALSE

⇒ To bypass a 100 ohm emitter resistor at
10 μF
100 μF
1000 μF
1 μF

⇒ A three stage telephone switching structure is to have 128 input and 128 output terminals. There are 16 first stage and 16 third stage matrices. To avoid blocking the number of intermediate paths required is
16
15
8
1

⇒ In a CD the sampling frequency is nearly
half the highest frequency in audio signal
equal to highest frequency in audio signal
double the highest frequency in audio signal
four times the highest frequency in audio signal

⇒ Registers and counters are similar in the sense that they both
count pulses
store binary information
are made from an array of flip-flops and gates integrated on a single chip
are shift registers

⇒ When a p-n-p transistor is properly biased to operate in active region the holes from emitter.
diffuse through base into collector region
recombine with electrons in base
recombine with electrons in emitter
none of the above

⇒ A 1000 kHz carrier wave modulated 40% at 4000 Hz is applied to a resonant circuit tuned to a carrier frequency and having Q = 140. What is the degree of modulation after transmission through this circuit?
0.4
0.2
0.27
0.54

⇒ The poles with greater displacement from the real axis correspond to
higher frequencies of oscillation
stable response
lower frequencies of oscillation
unbounded output

⇒

Assertion (A): A colour TV uses a SAW filter to give stable band pass response and high gain.

Reason (R): Devices using SAW principle are used in many systems.

Both A and R are correct and R is correct explanation of A
Both A and R are correct but R is not correct explanation of A
A is correct but R is wrong
A is wrong but R is correct

⇒ Satellite communication systems use the frequency band
10 to 20 MHz
50 to 70 MHz
3 to 6 GHz
100 to 120 GHz

⇒ A BJT is said to be operating in saturation region if
both junctions are reverse biased
both junctions are forward biased
base emitter junction is forward biased and base collector junction is reverse biased
base collector junction is forward biased and base emitter junction is reverse biased

⇒ Pulse modulation is used in
radio navigation
automatic landing equipment
data communications
all of the above

⇒

Assertion (A): In C a variable name can have upto 8 characters and special symbols can also be part of variable name.

Reason (R): In C a type declaration at the beginning of program indicates the type of variable name used in the program.

Both A and R are correct and R is correct explanation of A
Both A and R are correct but R is not correct explanation of A
A is correct R is wrong
A is wrong R is correct

⇒ The equation sin (z) = 10 has
no real or complex solution
exactly two distinct complex solutions
a unique solution
an infinite number of complex solutions

⇒ Which of the following semiconductor has the highest melting point?
Germanium
Silicon
Gallium arsenide
Lead sulphide

⇒ A low-pass filter frequency responce H (jω) = A (ω) e^jΦ(ω) does not produce any phase distortion, if
A(ω) = Cω², Φ (ω) = kω³
A(ω) = Cω², Φ (ω) = kω
A(ω) = Cω², Φ (ω) = kω²
A(ω) = C, Φ (ω) = kω^-1

⇒ The op amp is used in
A/D converters
D/A converters
both (a) and (b)
shift registers

⇒ A 2 bit binary multiplier can be implemented using
2 inputs ANDs only
2 inputs XORs and 4 input AND gates only
Two 2 inputs NORs and one XNOR gate
XOR gates and shift registers

⇒ Choose the correct match for input resistance of various amplifier configurations shown below configurat
CB-LO, CC-MO, CE-HI
CB-LO, CC-HI, CE-MO
CB-MO, CC-HI, CE-LO
CB-HI, CC-LO, CE-MO

⇒ In the given figure shows a 3 bit shift register using TTL flip flops. Initially all the flip flops are set to 0 state. After 8 clock pul
A = 1, B = 1, C = 1
A = 1, B = 1, C = 0
A = 0, B = 1, C = 1
A = 0, B = 0, C = 1

⇒ A triangular Pulse of 10 V peak is applied to a capacitor of 0.4 F. The change of the capacitor and its wavefor
8 rectangular
8 triangular
4 triangular
4 rectangular

⇒ In TV transmitter, the function of duplexer is
to amplify video signal
to remove distortions in audio signal
to combine outputs of visual and audio transmitters
to amplify audio signal

⇒ Industrial noise has the frequency range of
1 to 100 Hz
200 to 5000 Hz
above 200 MHz
1 to 600 MHz

⇒ For a paramagnetic material, susceptiblity increases with increasing temperature.
TRUE
FALSE

⇒ The radiation resistance of a λ/16 wire dipole in free space will be nearly
1 Ω
3 Ω
13 Ω
30 Ω

⇒ A Schottky diode clamp is used along with switching BJT for
reducing the power dissipation
reducing the switching time
increasing the value of β
reducing the base current

⇒ The time constant of a series RL circuit is
LR
L/R
R/L
e^-R/L