Question is ⇒ In the following limiter circuit, an input voltage V1 = 10 sin 100pt applied. Assume that the diode drop is 0.7 V when it is forward biased. The zener breakdown voltage is 6, Options are ⇒ (A) 6.1 V, -0.7 V, (B) 0.7 V, -7.5 V, (C) 7.5 V, -0.7 V, (D) 7.5 V, -7.5 V, (E) , Leave your comments or Download question paper.

Question is ⇒ In the following limiter circuit, an input voltage V1 = 10 sin 100pt applied. Assume that the diode drop is 0.7 V when it is forward biased. The zener breakdown voltage is 6, Options are ⇒ (A) 6.1 V, -0.7 V, (B) 0.7 V, -7.5 V, (C) 7.5 V, -0.7 V, (D) 7.5 V, -7.5 V, (E) , Leave your comments or Download question paper. Previous question Next question


Q1.	In the following limiter circuit, an input voltage V₁ = 10 sin 100pt applied. Assume that the diode drop is 0.7 V when it is forward biased. The zener breakdown voltage is 6
A.	6.1 V, -0.7 V [Wrong Answer]
B.	0.7 V, -7.5 V [Wrong Answer]
C.	7.5 V, -0.7 V [Correct Answer]
D.	7.5 V, -7.5 V [Wrong Answer]
View Answer 1 -1 Explanation:- Answer : C Discuss it below : !! OOPS Login [Click here] is required to post your answer/result Help other students, write article, leave your comments

Previous question Next question

Also Read Similar Questions Below :

⇒

Match the following:

	List I		List II
A.	Television	1.	Either AM or FM used
B.	Radio	2.	Both AM and FM are used
C.	Radar	3.	PCM is used
D.	Data Communication	4.	Digital system

A-4, B-3, C-1, D-2
A-2, B-1, C-3, D-4
A-4, B-1, C-3, D-2
A-2, B-3, C-1, D-4

⇒ Superheterodyne receiver can be used in
AM
FM
SSB
All of the above

⇒ A sequence detector is required to give a logical output of 1 whenever the sequence 1011 is detected in the incoming pulse stream. Minimum number of flip-flops needed to built the sequence detector is
4
3
1
2

⇒ A wire is carrying current I. The field intensity H at a distance r from the wire
is directed towards wire
is directed away from wire
is tangential every where to a circle of radius r
none of the above

⇒ The circuit shown in the figure
positive logic OR circuit
negative logic OR circuit
positive logic AND circuit
negative logic AND circuit

⇒ The spectrum of the white noise and an impulse function is similar in following aspects
both have similar magnitude spectrum
both have similar magnitude and Phase spectrum
no relation
similar phase spectrum

⇒ When a source is delivering maximum power to a load through a network, the ratio of power delivered to the source power
may be 50% or less than 50%
is 50%
may be 50% or more than 50%
may be 50% or more less than 50%

⇒ In a channel voice coder, the outputs of sixteen 20 Hz low pass filters are sampled, multiplexed and A/D converted. If sampling is at 40 samples/second and 3 bits/sample represents each voltage sample, the bit rate is about
1.9 k bits/sec
0.95 k bits/sec
3.8 k bits/sec
7.6 k bits/sec

⇒ Which of the following commutation methods is the overall circuit under damped?
Class A
Class B
Class C
Both class A and Class B

⇒

Assertion (A): Divide-64 counter is a Mod-64 counter and divides the input frequency by 64

Reason (R): A Mod 64 counter can be obtained by cascading Mod 16 and Mod 4 counters.

Both A and R are correct and R is correct explanation of A
Both A and R are correct but R is not correct explanation of A
A is true, R is false
A is false, R is true

⇒ In phase modulation, the phase deviation is
proportional to the amplitude of the signal and varies with frequency
remains constant while amplitude and frequency of signal varies
proportional to the amplitude of the signal and independent of the frequency
none of the above

⇒ If f(t) is in volts, then F(jω) is in
volts
volt seconds
volts/sec
volt-sec²

⇒ Bandwidth for practical PCM system is (where n is no. of channels, N length of PCM codes)
2n N f_m Hz
4n f_m Hz
2n f_m
(N + 1)f_m

⇒ A signal f(t) = cos 10pt + 3 cos 4pt is instantaneously sampled. The maximum allowable value of sampling interval T_s in sec is
1 / 4 sec
1 / 8 sec
1 / 8p sec
1 / 10 sec

⇒ A single phase cycloconverter with centre tapped input transformer requires
2 thyristors
4 thyristors
8 thyristors
either 2 or 4 thyristors

⇒ For a D/A converter, inputs and outputs are given. The output corresponding to digital input 01
2.0 V
2.5 V
3.0 V
4.0 V

⇒ For a reactance function H(s), the slope dH (jω)/dω is
0
always positive
always negative
either 0 or positive

⇒ Which device can detect the presence of both forward and backward waves in a waveguide?
Filter
Detector
Directional coupler
Magic T

⇒ For a given carrier wave, maximum undistorted power is transmitted when value of modulation is
1
0.8
0.5
0

⇒ Consider the following:

Distortion
Gain
Bias stabilization
Sensitivity
Frequency response

Which of these properties of the power amplifier one should concentrate upon while designing a good power amplifier circuit?
1, 2 and 3
1, 3 and 5
2, 3 and 4
4 and 5

⇒ An end fire array consisting of several half-wave lengths of directive gain 40, then array length will be
10 λ
100 λ
20 λ
5 λ

⇒ In P-N junction, the region containing the uncompensated acceptor and donor ions is called
transition zone
depletion region
neutral region
active region

⇒ As temperature increases the number of free electrons and holes in an intrinsic semiconductor
increases
decreases
remains the same
may increase or decrease

⇒ Which of the following frequencies cannot be used for reliable beyond-the-horizon terrestrial communications without repeaters?
25 kHz
15 MHz
750 MHz
12 GHz

⇒ When a current carrying conductor is brought into magnetic field, the force that moves the conductor depends upon
the value of current
the weight of the conductor
the direction of the conductor
none of the above

⇒ F.T. of continuous non-periodic signal is
aperiodic
periodic
a and b
none

⇒ In amplitude modulation the rms value of radio frequency voltage after 40% modulation is 60 mV. If modulation is 80% the rms value after modulation will be about
50 mV
60 mV
66 mV
80 mV

⇒ The distributors for residential areas are
single phase
three phase three wire
three phase 4 wire
(a) or (b)

⇒ What is the purpose of peak clipper circuits in radio transmitters?
To prevent overmodulation
To reduce bandwidth
To increase bandwidth
To regulate oscillator I/P voltage

⇒ As regards BCH code, Hamming code and Reed-Solomon code
BCH and Hamming code are special cases of Reed-Solomon code
Reed-Solomon and Hamming code are special cases of BCH code
BCH and Reed-Solomon code are special case of Hamming code
none of the above