Question is ⇒ In terms of classical representation of electrons, Options are ⇒ (A) an atom is essentially empty, (B) an atom is essentially full, (C) an atom may be essentially empty or full depending on the material, (D) an atom may be essentially empty or full depending on temperature, (E) , Leave your comments or Download question paper.

Question is ⇒ In terms of classical representation of electrons, Options are ⇒ (A) an atom is essentially empty, (B) an atom is essentially full, (C) an atom may be essentially empty or full depending on the material, (D) an atom may be essentially empty or full depending on temperature, (E) , Leave your comments or Download question paper. Previous question Next question


Q1.	In terms of classical representation of electrons
A.	an atom is essentially empty [Correct Answer]
B.	an atom is essentially full [Wrong Answer]
C.	an atom may be essentially empty or full depending on the material [Wrong Answer]
D.	an atom may be essentially empty or full depending on temperature [Wrong Answer]
View Answer 2 -1 Explanation:- Answer : A Discuss it below : !! OOPS Login [Click here] is required to post your answer/result Help other students, write article, leave your comments

Previous question Next question

Also Read Similar Questions Below :

⇒ An FM radio receiver which is tuned to a 91.6 MHz broadcast station may receive an image frequency of __________ MHz.
102.3
113
70.2
80.9

⇒ If number of information bits is 4, the parity bits in Hamming code are located at bit positions __________ from the LSB.
1, 2, 5
1, 2, 4
1, 2, 3
1, 2

⇒ A source of angular frequency 1 rad sec has a source impedance consisting of 1 Ω resistance in series with 1 H inductance. The load that will obtained the maximum power transfer is
1 Ω resistance
1 Ω resistance in parallel with 1 H inductance
1 Ω resistance in series with 1 F capacitor
1 Ω resistance in parallel with 1 F capacitor

⇒ The signumm function written as [sgn(t)] is defined as
sgn(t) = - 1 for t < 0, = 0 for t = 0 and = 1 for t > 0
sgn(t) = 1 for t < 0, = 0 for t = 0 and = - 1 for t > 0
sgn(t) = 0 for t < 0, = 1 for t = 0 and = 0 for t > 0
sgn(t) = 0 for t < 0, = 1 for t³ 0

⇒ Ripple factor RF and form factor FF are related as
RF = FF² - 1
RF = (FF² - 1)^0.5
RF = FF - 1
RF = (FF - 1)^0.5

⇒ In a satellite system circular polarization is to be obtained. The antenna used is
parabolic
horn
log periodic
helical

⇒ Which of the following codes is based on BCD format?
EBCDIC
ASCII
Hollerith
both (a) and (b)

⇒ Efficiency of class A power amplifier is very poor.
TRUE
FALSE

⇒ Each cell of a static RAM has
4 MOS transistors
4 MOS transistors and 2 capacitors
2 MOS transistors and two capacitors
1 MOS transistor and 1 capacitor

⇒ A two branch parallel circuit has a 10 Ω resistance and 0.5 H inductance in one branch and a 100 μF capacitor in the second branch. It is fed from 100 V ac supply. At resonance, the source current is
0.416666666666667
0.0416666666666667
0.2 A
0.05 A

⇒ When an electromagnetic wave travelling in one medium strikes upon a second medium (having a different conductivity) the wave will be
totally transmitted
totally reflected
neither transmitted nor reflected
partially transmitted and partially reflected

⇒ Machine cycle is always the same as instruction cycle.
TRUE
FALSE

⇒ In a 4 input AND gate, the total number of High outputs for 16 input states are
16
8
4
1

⇒ In a N-P-N transistor the function of the emitter is
to emit or inject holes into the collector
to emit or inject electrons into the collector
to emit or inject electrons into the base
to emit or inject holes into the base

⇒ A system with transfer function H(z) has impulse response h(.) defined as h(2) = 1, h(3) = -1 and h(k) = 0 otherwise. Consider the following statem
Only S2 is true
Both S1 and S2 are false
Both S1 and S2 are true, and S2 is a reason for S1
Both S1 and S2 are true, but S2 is not a reason for S1

⇒ Which one of the following is digital?
Pulse code modulation
Pulse width modulation
Pulse frequency modulation
Pulse position modulation

⇒ In a radio receiver with simple AGC
the highest AGC voltage is produced between stations
the faster the AGC time constant, the more accurate the output
an increase in signal strength produces more AGC
the audio stage gain is normally controlled by AGC

⇒ Wave A starts its positive half cycle at ωt = 30° and wave B starts its positive half cycle at ωt = 75° then wave B is leading wave A by 45°.
TRUE
FALSE

⇒ RMS value of i(t) = 10[1 + sin (- t)] is
10
10/2
l50
102

⇒ Two coils having self inductances of 10 mH and 40 mH are mutually coupled. The maximum possible mutual inductance is
40 mH
20 mH
10 mH
5 mH

⇒ In 8085
RST 6.5 and RST 5.5 are high level sensitive interrupts
RST 6.5 and RST 5.5 are low level sensitive interrupts
RST 5.5 is low level sensitive interrupt but RST 5.5 is high level-sensitive interrupt
RST 5.5 is low level sensitive interrupt but RST 6.5 is high level sensitive interrupt

⇒ Unlimited number of ICs 7490, 78492 and 7493 are available. Which of these could be used to build the dividse-by-60 circuit of fi
7490
7492
combination of 7490 and 7492
combination of 7492 and 7493

⇒ The voltage gains of an amplifier without feedback and with negative feedback respectively are 100 and 20. The percentage of negative feedback (β) would be
0.4
0.05
0.2
0.8

⇒ Computers use thousands of flip-flops. To coordinate the overall action, a common signal is sent to all flip-flop known as
debug signal
toggle signal
active signal
clock signal

⇒ Which of the following semiconductor has the highest melting point?
Germanium
Silicon
Gallium arsenide
Lead sulphide

⇒ The subcarrier frequency for transmission of colour difference signals in TV systems in India is
9.47 MHz
4.43 MHz
2.06 MHZ
1.3 MHz

⇒ Which of the following is not a specification of D/A and A/D converters?
Gain
Drift
Speed
Accuracy

⇒ Load Z_L for maximum power transfe
R
R + jωL
R - jωL
none

⇒ A material has conductivity of 10^-2 mho/m and a relative permittivity of 4. The frequency at which conduction current in the medium is equal to displacement current is
45 MHz
90 MHz
450 MHz
900 MHz

⇒ Space communication links are being increasingly moved into Ka-band (200-30 GHz) because it
offers a much wider available bandwidth
does not suffer from atmospheric at tenuation
permits the use of smaller antenna
does not suffer from rain attenuation