Question is ⇒ In radio receiver, the maximum contribution to noise is from, Options are ⇒ (A) mixer stage, (B) power supply, (C) power amplifier, (D) equally from above three, (E) , Leave your comments or Download question paper.

Question is ⇒ In radio receiver, the maximum contribution to noise is from, Options are ⇒ (A) mixer stage, (B) power supply, (C) power amplifier, (D) equally from above three, (E) , Leave your comments or Download question paper. Previous question Next question


Q1.	In radio receiver, the maximum contribution to noise is from
A.	mixer stage [Wrong Answer]
B.	power supply [Wrong Answer]
C.	power amplifier [Correct Answer]
D.	equally from above three [Wrong Answer]
View Answer 2 -3 Explanation:- Answer : C Discuss it below : !! OOPS Login [Click here] is required to post your answer/result Help other students, write article, leave your comments

Previous question Next question

Also Read Similar Questions Below :

⇒ The coefficients F_n in the exponential form of Fourier series are
independent of frequency
functions of frequency
even function of frequency
odd functions of frequency

⇒ Pulse modulation is used in
radio navigation
automatic landing equipment
data communications
all of the above

⇒ For the two ports in figure, y₁₁ = 8 mho, y₁₂ = y₂₁ = -6 mho and y₂₂ = 6 mho. The values of Y_A, Y_B, Y_C respectively
2, 6, 6 mho
2, 6, 0 mho
2, 0, 6 mho
2, 6, 8 mho

⇒ Determine the correctness or otherwise of the following Assertion [a] and the Reason
Both [a] and [r] are true and [r] is the correct reason for [a]
Both [a] and [r] are true but [r] is not the correct reason for [a]
Both [a] and [r] are false
Both [a] and [r] are true

⇒ For the collector-feedback amplifier shown below the voltage gain A_v will be _________
-113.07
-103.07
-107.07
-93

⇒ A 200 turn coil has a self inductance of 10 mH. If the number of turns is doubled, all other quantities remaining the same, the self inductance will be
2.5 mH
5 mH
20 mH
40 mH

⇒ Degaussing in a picture tube means
Adding magnetism in mask and mounting frame
Removing residual magnetism in mask, shield etc...
Increasing resistance of coils to decrease time constant
Decreasing resistance of coils to increase time constant.

⇒

Assertion (A): In 8085, P flag is for parity checking.

Reason (R): If the result of ALU has even parity, P flag is set and if the result has odd parity, P flag is reset.

Both A and R are correct and R is correct explanation of A
Both A and R are correct but R is not correct explanation of A
A is correct R is wrong
A is wrong R is correct

⇒ In the equivalent circuit of a moving coil cone type loudspeaker, the mass of the moving system is represented by
a resistance
a capacitance
an inductance
a conductance

⇒ The conductivity of germanium increases by about 6 percent per degree increase in temperature.
TRUE
FALSE

⇒ Two voltmeters 0-250 V each having resistances of 5 kΩ and 10 kΩ respectively and are connected in series. To ensure that neither of them goes beyond scale the total voltage which can be applied should be less than
500 V
400 V
375 V
250 V

⇒ For low impedance SAW filter the most suitable material for substrate of SAW filter is
PZT ceramics
ZnO
Lithium titanate
Lithium neobate

⇒ Which of these triggering methods for series connected SCRs use LASCR in the gate circuit?
Resistance triggering
Simultaneous triggering
Sequential triggering
Optical triggering

⇒ For an npn transistor connected as shown in the figure V_BE = 0.7 volts. Given that reverse saturation current of the junction at room temperature 300K is 10^-13A, the emitter curr
30 mA
39 mA
49 mA
20 mA

⇒ A network contains only independent current source and resistors. If the values of all resistors are doubled, the value of the node voltage
will become half
will remain unchange
will become one third
cannot be determined unless the circuit configuration and the values of the resistors are known

⇒ The output, V-I characteristics of an Enhancement type MOSFET has
only an ohmic region
only a saturation region
an ohmic region at low voltage value followed by a saturation region at higher voltages
an ohmic region at large voltage values preceded by a saturation region at lower voltages

⇒ Magnetic susceptibility of a medium is the ratio of
magnetic field strength to mmf
intensity of magnetization to magnetic flux density
intensity of magnetization to field strength
mmf to magnetic field strength

⇒ In the circuit shown in figure, maximum power will be transferred
Z_L = 13 - j 9
Z_L = 13 + j 9
Z_L = 9 - j 13
Z_L = 9 + j 13

⇒ In a thyristor, the forward breakover voltage
is constant
may be constant or may depend on gate current
decreases as gate current is increased
increases as gate current is increased

⇒ A collector collects
electrons from the base in case of N-P-N transistor
electrons from the emitter in case P-N-P transistor
holes from the base in case of N-P-N transistor
holes from the base in case of P-N-P transistor

⇒ The transfer function of a zero-order-hold system is :
(l/s)(l + e^-sT)
(1/s)(1 - e^-sT)
1 - (l/s)e^-sT
1 + (1/s)e^-sT

⇒ A machine cycle has one clock cycle.
TRUE
FALSE

⇒ Figure shows the arrangement
FM
PM
AM-DSB
AM-SSB

⇒ The percentage saving in power of 100% modulated suppressed carrier AM signal is
100
75
66.6
50

⇒ The correct sequence of subsystems in an FM receiver is
Mixer, RF amplifier, Limiter, IF amplifier. Discriminator, Audio amplifier
RF amplifier, Mixer, IF amplifier, Limiter, Discriminator, Audio amplifier
RF amplifier, Mixer, Limiter, Discriminator IF amplifier, Audio amplifier
Mixer, IF amplifier, RF amplifier, Audio amplifier, Discriminator

⇒ Which distortion is least objectionable in case of audio amplifiers?
Phase distortion
Frequency distortion
Harmonic distortion
Inter-modulation distortion

⇒ A silicon diode is forward biased and total applied voltage is 5 V. The voltage across p-n junction is
5 V
Slightly less than 5 V
0.7 V
0

⇒ Find resistance R_B to bring transistor to threshold of saturation V_CB = 0, V_BE = 0.7 V, a =
1.5 kΩ
15 kΩ
10 kΩ
1 kΩ

⇒ Symbol shown in figure represen
P-channel DEMOSFET
N-channel DEMOSFET
UJT with N-type base
UJT with P-type base

⇒ One commercial unit of energy is equal to
1 watt-sec
1 kilowatt-sec
1 kilowatt-hour
One watt-hour