Question is ⇒ In radar display system PPI stands for, Options are ⇒ (A) Pulse Position Indicator, (B) Plan Position Indicator, (C) Phase Position Indicator, (D) Point Position Indicator, (E) , Leave your comments or Download question paper.

Question is ⇒ In radar display system PPI stands for, Options are ⇒ (A) Pulse Position Indicator, (B) Plan Position Indicator, (C) Phase Position Indicator, (D) Point Position Indicator, (E) , Leave your comments or Download question paper. Previous question Next question


Q1.	In radar display system PPI stands for
A.	Pulse Position Indicator [Wrong Answer]
B.	Plan Position Indicator [Correct Answer]
C.	Phase Position Indicator [Wrong Answer]
D.	Point Position Indicator [Wrong Answer]
View Answer 1 -2 Explanation:- Answer : B Discuss it below : !! OOPS Login [Click here] is required to post your answer/result Help other students, write article, leave your comments

Previous question Next question

Also Read Similar Questions Below :

⇒ In the given figure, of potentiometer V₀ = V_i (R₀/R_i) only
R_L = 0
R_L = ∞
R_L is neither low nor high
R_L is low but not zero

⇒ The op-amp circuit shown in the figure is a filter. The type of filter and its cut off type of filter and its cut off frequency are respectiv
high Pass, 1000 rad/sec
low Pass, 100 rad/sec
high Pass, 10000 rad/sec
low pass, 10000 rad/sec

⇒ The system of linear equations 4x + 2y = 1 , 2x + y = 6 has
a unique solution
no solution
an infinite number of solutions
exactly two distinct solutions

⇒ When a 10 K, 10%, 1/4 Ω resistor is connected in series with a 12 K, ± 1%, 1/4 Ω resistor, the resulting combination has the following specifications
22 K, ± 11%, 1/2 Ω
22 K, ± 5.5%, 1/2 Ω
22 K, ± 5.5%, 1/8 Ω
none of these

⇒ A higher value of Standing Wave Ratio indicates
least mismatch between line and load
greater mismatch between load and line
number of nodes is equal to the number of antinodes
none of the above

⇒ A 4 input AND gate is equivalent to
4 switches in parallel
2 switches in series and 2 in parallel
three switches in parallel and one in series
4 switches in series

⇒ In a BCD to 7 segment decoder the minimum and maximum number of outputs active at any time is
2 and 7
3 and 7
1 and 6
3 and 6

⇒ Which of these are universal gates?
Only NOR
Only NAND
Both NOR and NAND
NOR, NAND, OR

⇒ What was the first commercial geostationary communication satellite?
INTELSAT 1
ECHO
INSAT-1A
SPUTNIK

⇒ The angular location of poles depends on
undamped natural frequency
damping ratio
both (a) and (b)
neither (a) nor (b)

⇒ A limiter circuit can be built using a diode and resistance.
TRUE
FALSE

⇒ The sign of a floating point number depends on
only the sign of mantissa
only the sign of exponent
the sign of both mantissa and exponent
either (a) or (b)

⇒ In a high speed modem the data rate handled is about
1000 bps
5000 bps
20000 bps
50000 bps

⇒ Read the following statement

Multi-processing operation permits highly efficient parallel processing at several levels.
Multi processing involves use of several processing units jointly on a common program and severally on different programs.
In multi-processing the assignment of facilities to tasks, loading of programs and monitoring of I/O activity is taken care of by operating system.

Which of the above are correct?
All
1 and 2 only
1 and 3 only
2 and 3 only

⇒ Data can be changed from spatial code to temporal code and vice-versa by using
ADC and DAC
shift Register
synchronous counter
timers

⇒ Which of the following is the indirect way of FM generation?
Reactance bipolar transistor modulator
Armstrong modulator
Varactor diode modulator
Reactance FM modulator

⇒ Thermal run away of a transistor occurs when
heat dissipation from transistor is excessive
transistor joints melt due to high temperature
there is excessive leakage current due to temperature rise
none of the above

⇒ Consider the following statemen
1, 2, 3, 4
1, 2, 3
1, 2
1, 3, 4

⇒ If sequence y(n) = x(-n) then it is
Causal
Non-Causal
Depends on x(-n)
None

⇒ In a transistor the minimum and maximum values of β_dc are 100 and 121. The proper value of β_dc to be used to locate Q point is
100
121
110.5
110

⇒ In a p-n-p transistor operating in forward active mode
base is positive with respect to emitter and collector
base is negative with respect to emitter and collector
emitter is positive with respect to base and base is positive with respect to collector
emitter is negative with respect to base and base is positive with respect to collector

⇒ The characteristic equation for the next state (Q_n+1) of a J-K flip-flop is
Q_n+1 = JQ_n + KQ_n
Q_n+1 = JQ_n + KQ_n
Q_n+1 = JQ_n + KQ_n
Q_n+1 = JQ_n + KQ_n

⇒ The circuit of the given figure realizes the func
Y = (A + B) C + DE
Y = A + B + C + D + E
AB + C +DE
AB + C(D + E)

⇒ A full wave rectifier using centre tapped transformer and a bridge rectifier use similar diodes and have equal no load output voltage. Under equal load conditions
Output voltage of bridge rectifier
Output voltage of bridge rectifier will be more than that of other
Output voltage of both will be exactly equal
Output voltage of any one may be more than that of other

⇒ In a circuit the value of resistor is made four times. The noise voltage generated by this resistance will
be doubled
be increased four times
remain the same
become half

⇒ In figure v₁ = 8 V and v₂ = 4 V. Which diode will cond
D₂ only
D₁ only
Both D₁ and D₂
Neither D₁ nor D₂

⇒ FM has
two sidebands only
four sidebands only
eight sidebands only
infinite sidebands

⇒ The storage capacity of a CD is
360 k bytes per side
360 M bytes per side
540 k bytes per side
540 M bytes per side

⇒ The ASCII code is for information interchange by a binary code for
alphabet only
number only
alpha-numeric and other common symbols
none of these

⇒ The logic circuit given below converts a binary code y₁ y₂, y₃
Excess - 3 code
Gray code
BCD code
Hamming