Question is ⇒ In plane tabling, the straight lines, angles and triangles are constructed by, Options are ⇒ (A) Protractor, (B) Divider, (C) Graphical method, (D) Planimeters, (E) , Leave your comments or Download question paper.

Question is ⇒ In plane tabling, the straight lines, angles and triangles are constructed by, Options are ⇒ (A) Protractor, (B) Divider, (C) Graphical method, (D) Planimeters, (E) , Leave your comments or Download question paper. Previous question Next question


Q1.	In plane tabling, the straight lines, angles and triangles are constructed by
A.	Protractor [Wrong Answer]
B.	Divider [Wrong Answer]
C.	Graphical method [Correct Answer]
D.	Planimeters [Wrong Answer]
View Answer 27 -4 Explanation:- Answer : C Discuss it below : Amjad Ali Said on 2020-02-15 17:01:03 Graphical method !! OOPS Login [Click here] is required to post your answer/result Help other students, write article, leave your comments

Previous question Next question

Also Read Similar Questions Below :

⇒ Closed contours of decreasing values towards their centre, represent.
a hill
a depression
a saddle or pass
a river bed.

⇒ The number of horizontal cross wires in a stadia diaphragm is
one
two
three
four

⇒ Deviation of the actual road gradient from the proposed contou'r gradient up hill side, involves.
embankment on the centre line
excavation on the centre line
earth work on the centre line
none of these.

⇒ Subtense tacheometry is generally preferred to if ground is.
flat
undulating
mountaineous
deserts.

⇒ Offsets are measured with an accuracy of 1 in 40. If the point on the paper from both sources of error (due to angular and measurement errors) is not to exceed 0.05 cm on a scale of 1 cm = 20 m, the maximum length of offset should be limited to.
14.14
28.28 m
200 m
none of these.

⇒ For the construction of highway (or railway).
longitudinal sections are required
cross sections are required
both longitudinal and cross sections are required
none of these.

⇒ In geodetic surveys higher accuracy is achieved, if.
curvature of the earth surface is ignored
curvature of the earth surface is taken into account
angles between the curved lines are treated as plane angles
none of these.

⇒ The correction to be applied for eliminating the effect of earth's curvature is
Additive
Subtractive
Compensating
Cumulative

⇒ If the end stations of a line are free from local attraction, then the difference in between fore and back bearing of that line should be
180°
120°
360°
90°

⇒ The tangent to the liquid surface in a level tube, is parallel to the axis of the level tube at.
every point of the bubble
either end of the bubble
the mid-point of the bubble
no where.

⇒ While measuring the distance between two points along upgrade with the help of a 20 m chain, the forward end of the chain is shifted forward through a distance.
20 (sin Î¸ - 1)
20 (cos Î¸ - 1)
20 (sec Î¸ - 1)
20 (cosec Î¸ - 1).

⇒ Transition curves are introduced at either end of a circular curve, to obtain.
gradually decrease of curvature from zero at the tangent point to the specified quantity at the junction of the transition curve with main curve
gradual increase of super-elevation from zero at the tangent point to the specified amount at the junction of the transition curve with main curve
gradual change of gradient from zero at the tangent point to the specified amount at the junction of the transition curve with main curve
none of these.

⇒ Pick up the correct statement from the following :
The directions of plumb lines suspended at different points in a survey are not strictly parallel
In surveys of small extent, the effect of curvature may be ignored and the level surface of the earth is assumed as horizontal
In surveys of large extent, the effect of curvature of the earth must be considered
All the above.

⇒ True meridian of different places.
converge from the south pole to the north pole
converge from the north pole to the south pole
converge from the equator to the poles
run parallel to each other.

⇒ Horizontal distances obtained by thermometric observations
require slope correction
require tension correction
require slope and tension corrections
do not require slope and tension corrections

⇒ A uniform slope was measured by the method of stepping. If the difference in level between two points is 1.8 m and the slope distance between them is 15 m, the error is approximately equal to.
cumulative, + 0.11 m
compensating, Â± 0.11 m
cumulative, - 0.11 m
none of these

⇒ The difference in the lengths of an arc and its subtended chord on the earth surface for a distance of 18.2 km, is only.
1 cm
5 cm
10 cm
100 cm.

⇒ The correction for sag is
always additive
always subtractive
always zero
sometimes additive and sometimes subtractive

⇒ The length of a chain is measured from
centre of one handle to centre of other handle
outside of one handle to outside of other handle
outside of one handle to inside of other handle
inside of one handle to inside of other handle

⇒ In a theodolite.
the telescope axis is perpendicular to transit axis
the axis of rotation is perpendicular to transit axis
the telescope axis, the transit axis and the rotation axis pass through the centre of theodolite
all the above.

⇒ One of the tacheometric constants is additive, the other constant, is.
subtractive constant
multiplying constant
dividing constant
indicative constant.

⇒ If the radius of a simple curve is R, the length of the chord for calculating offsets by the method of chords produced, should not exceed.
R/10
R/15
R/20
R/25.

⇒ The survey, in which the curvature of earth is ignored, is called as
Plane survey
Geodetic survey
Geological survey
Aerial survey

⇒ A horizontal angle which a line makes with the true meridian through one of the extremities of the line is called
Bearing
True bearing
Imaginary bearing
Maimetic bearing

⇒ The chord of a curve less than peg interval, is known as.
small chord
sub-chord
normal chord
short chord.

⇒ An offset more than 15m in length is known as
Long offset
Short offset
Oblique offset
Right-angled offset

⇒ A bearing of a line is also known as.
magnetic bearing
true bearing
azimuth
reduced bearing

⇒ The length of a traverse leg may be obtained by multiplying the latitude and.
secant of its reduced bearing
sine of its reduced bearing
cosine of its reduced bearing
tangent of its reduced bearing.

⇒ In a precision traverse, included angles are measured by setting the vernier.
to read zero exactly on back station
to read 5Â° exactly on back station
some where near zero and reading both verniers on back station
all the above.

⇒ When the plane table is not correctly oriented, the resectors will
Meet at a point
Form a triangle
Either of the above
None of the above