Users Also Read

MCQ's Search Engine

Electrical Engineering

Mechanical Engineering

Civil Engineering

Automobile Engineering

Chemical Engineering

Computer Engineering

Electronics Engineering

Medical Science Engg

Q1. | In moment distribution method, the sum of distribution factors of all the members meeting at any joint is always |

A. | zero [Wrong Answer] |

B. | less than 1 [Wrong Answer] |

C. | 1 [Correct Answer] |

D. | greater than 1 [Wrong Answer] |

View Answer
Explanation:-
Answer : CDiscuss it below :!! OOPS Login [Click here] is required to post your answer/resultHelp other students, write article, leave your comments |

**Also Read Similar Questions Below :**

⇒ The stiffness method in structural analysis is also known as

Unit load method

Consistent deformation method

Force method

Displacement method

⇒ While using three moments equation, a fixed end of a continuous beam is replaced by an additional span of

zero length

infinite length

zero moment of inertia

none of the above

⇒ For earthquake resistant masonry buildings, where seismic coefficient is less than 0.08, the horizontal distance between two openings shall not be less than

Vt x height of shorter opening

Vt x height of longer opening

Ax height of shorter opening

Vi x height of longer opening

⇒ A single rolling load of 8 kN rolls along a girder of 15 m span. The absolute maximum bending moment will be

8 kN.m

15 kN.m

30 kN.m

60 kN.m

⇒ In a cavity wall, both leaves of which are load bearing, the effective thickness is taken as

sum of thickness of both leaves

two-third of the sum of thickness of both the leaves

actual thickness of the stronger leaf

larger of (b) and (c)

⇒ A free standing brick wall 20 cm thick is subjected to a wind pressure of 75kg/m2. The maximum height of wall from stability consideration is

0.64 m

0.96 m

1.28 m

1.5 m

⇒ The number of independent displacement components at each joint of a rigid-jointed space frame is

1

2

3

6

⇒ The deformation of a spring produced by a unit load is called

stiffness

flexibility

influence coefficient

unit strain

⇒ Which of the following methods of structural analysis is a displacement method ?

moment distribution method

column analogy method

three moment equation

none of the above

⇒ Which of the following is not the displacement method ?

Equilibrium method

Column analogy method

Moment distribution method

Kani's method

⇒ In plastic analysis the shape factor for a circular section is

1.5

1.6

1.7

1.75

⇒ The method of moment distribution in structural analysis is

An iterative method

An exact method

An approximate method

None of these

⇒ Bending moment at any section in a conjugate beam gives in the actual beam

slope

curvature

deflection

bending moment

⇒ In the case of panel wall subjected to horizontal loads at right angles to the plane of the wall, with the mortar not leaner than Ml type, tensile stress in bending in the vertical direction may be allowed to the extent of

0.4 kg/cm2

0.7 kg/cm2

1.0 kg/cm2

1.2 kg/cm2

⇒ If there are m unknown member forces, r unknown reaction components and j number of joints, then the degree of static indeterminacy of a pin-jointed plane frame is given by

m + r + 2j

m - r + 2j

m + r - 2j

m + r - 3j

⇒ For a two-hinged arch, if one of the supports settles down vertically, then the horizontal thrust

is increased

is decreased

remains unchanged

becomes zero

⇒ In column analogy method, the area of an analogous column for a fixed beam of span L and flexural rigidity El is taken as

L/EI

L/2EI

L/3EI

L/4EI

⇒ The principle of virtual work can be applied to elastic system by considering the virtual work of

internal forces only

external forces only

internal as well as external forces

none of the above

⇒ Water retentivity for brick masonry should not be less than

50%

60%

70%

80%

⇒ The thickness of each leaf of a cavity wall shall not be less than

5 cm

7.5 cm

10 cm

15 cm

⇒ For a single point load W moving on a symmetrical three hinged parabolic arch of span L, the maximum sagging moment occurs at a distance x from ends. The value of x is

0.211 L

0.25 L

0.234 L

0.5 L

⇒ The degree of static indeterminacy up to which column analogy method can be used is

2

3

4

unrestricted

⇒ For masonry built in 1:1:6 cement-lime-sand mix mortar or equivalent, the horizontal shear stress permissible on the area of a mortar bed joint is

0.15 MPa

0.125 MPa

0.1 MPa

0.075 MPa

⇒ The number of independent equations to be satisfied for static equilibrium in a space structure is

2

3

4

6

⇒ The basic stress in masonry units having height to width ratio of 1.5 may be increased by a factor of

1.2

1.4

1.6

2.0

⇒ The torsional stiffness of a member can be defined as

Torque for unit moment

Torque for unit twist

Moment for unit twist

Torsion for unit twist

⇒ The method of virtual work in the analysis of structures results is

Compatible deformations

Equilibrium of forces

Stress strain relations

None of these

⇒ Effects of shear force and axial force on plastic moment capacity of a structure are respectively to

increase and decrease

increase and increase

decrease and increase

decrease and decrease

⇒ Weaker mortar. Of these statements

2 and 3 are correct

1 and 2 are correct

1 and 3 are correct

1, 2 and 3 are correct

⇒ For a symmetrical two hinged parabolic arch, if one of the supports settles horizontally, then the horizontal thrust

is increased

is decreased

remains unchanged

becomes zero