Question is ⇒ In microwave circuits, a mode transducer is used to, Options are ⇒ (A) change mode of wave transmission, (B) change direction of wave transmission, (C) change polarization of wave transmission, (D) change mode, direction or polarization wave transmission, (E) , Leave your comments or Download question paper.

Question is ⇒ In microwave circuits, a mode transducer is used to, Options are ⇒ (A) change mode of wave transmission, (B) change direction of wave transmission, (C) change polarization of wave transmission, (D) change mode, direction or polarization wave transmission, (E) , Leave your comments or Download question paper. Previous question Next question


Q1.	In microwave circuits, a mode transducer is used to
A.	change mode of wave transmission [Wrong Answer]
B.	change direction of wave transmission [Wrong Answer]
C.	change polarization of wave transmission [Wrong Answer]
D.	change mode, direction or polarization wave transmission [Correct Answer]
View Answer 1 -1 Explanation:- Answer : D Discuss it below : !! OOPS Login [Click here] is required to post your answer/result Help other students, write article, leave your comments

Previous question Next question

Also Read Similar Questions Below :

⇒ Which of the following DO statements is invalid in FORTRAN 77?
DO 161 = 1, 15
DO 16 1 = 1, 10, 1
DO 16 I = - 5, 5, 2
none of the above

⇒ Consider the following digital circu
1 and 2
3 and 4
1, 2 and 3
1, 2, 3 and 4

⇒ Which of the following is not a characteristic of a flip flop?
It is a bistable device
It has two outputs
It has two outputs are complement of each other
It has one input terminal

⇒ Which one of the following theorem can be conveniently used to calculate the power consumed by the 10 Ω resistor in the network shown in the above fig
Thevenin's theorem
Maximum power transfer theorem
Millman's theorem
Superposition theorem

⇒ A thyristor has a maximum allowable junction temperature of 120°C and the ambient temperature is 40°C. If thermal resistance is 1.6° C/W, the maximum allowable internal power dissipation is
20 W
50 W
92 W
128 W

⇒ Which of the following is NOT associated with a p-n junction?
Junction capacitance
Charge Storage Capacitance
Depletion Capacitance
Channel Length Modulation

⇒ 4 point DFT for x(n) = {2, - 1, 2, 3} is
{6, 4 - 2j, 2, 2j}
{6, 4j, 2, - 4j}
{6, -1 + 3j, 4 - 4j, 4 - 2}
{6, 2j, 4 - 2j, - 2 + 2j}

⇒ Which one condition is true to check the periodically for discrete time signal (where K is any integer, N is period, f₀ is frequency of signal)
f₀ = K/N
f₀ = K + N
f₀ = KN
f₀ = N/K

⇒ The number of logic devices required in a Mod-16 synchronous counter are
4
5
6
7

⇒ Feedback factor may be less or more than 1.
TRUE
FALSE

⇒ In figure the output V₀
2V₁ + V₂ - 2V₃
2(V₁ + V₂) - V₃
V₁ + V₂ + V₃
V₁ + 2V₂ - V₃

⇒ All of the following elements have three valence electrons EXCEPT
boron
indium
gallium
arsenic

⇒ Polar plot of a lag-lead compensator is a circle.
TRUE
FALSE

⇒ Two capacitors of 1 μF and 2 μF are connected in series across a 10 V dc battery. After the capacitors have been charged, the charges across the two capacitors will be
10 μC each
20 μC each
10 μC and 20 μC
20 μC and 10 μC

⇒ If noise margin is high, there is lesser chance of false operation.
TRUE
FALSE

⇒ For the logic circuit of the given figure,
A + BC
BC
AB
AB + C

⇒ When the number of quantising levels is 16 in PCM, the number of pulses in a code group will be
3
4
8
16

⇒ For a photo conductor with equal electron and hole mobilities and perfect ohmic contacts at the ends, an increase in the intensities of optical illumination results in
change in open circuit voltage
change in short circuit current
a reduction resistance
an increase of resistance

⇒ Current requirement of a piezo buffer is about
100mA
20mA
4mA
0.4mA

⇒ The current gain of a bipolar transistor drops at high frequencies because of
transistor capacitance
high current effects in the base
parasitic inductive elements
the early effect

⇒ The input gate current of a FET is
a few amperes
a few milli amperes
a few micro amperes
negligible

⇒ The number of select lines in ALU 1C 74181 is
2
4
8
16

⇒ An SR flip flop can be built using
NOR gate only
NAND gate only
either NOR or NAND gates
neither NOR nor NAND gates

⇒ Which of the following statement about receivers is false?
Double conversion is used to improve image rejection
Double conversion is used to improve selectivity
Variable sensitivity is used to improve selectivity
Variable sensitivity is used to eliminate selective fading

⇒ Which of the following is correct?
y₂₂ = z₂₂/|z|
y₁₁ = z₂₂/|z|
z₁₁ = y₁₁/|y|
z₂₂ = y₂₂/|y|

⇒ When deflecting torque and braking torque in an energy meter are zero,
the disc rotates at steady speed
the disc is stationary
the disc accelerates
the disc retards

⇒ For ideal performance, a filter should be terminated in characteristic impedance.
TRUE
FALSE

⇒ EEPROM is also known as
UVPROM
EAPROM
both UVPROM and EAPROM
none of the above

⇒ The sum of two sine waves of different frequencies is a sine wave.
TRUE
FALSE

⇒ As per time displacement theorem in Laplace transformation, displacement in the time domain by T becomes
division by s in the s domain
division by e^-sT in the s domain
multiplication by s in the s domain
multiplication by e^-sT in the s domain