Question is ⇒ In Laplace transform, multiplication by e-at in time domain becomes, Options are ⇒ (A) translation by a in s domain, (B) translation by (-a) in s domain, (C) multiplication by e-as in s domain, (D) none of the above, (E) , Leave your comments or Download question paper.

Question is ⇒ In Laplace transform, multiplication by e-at in time domain becomes, Options are ⇒ (A) translation by a in s domain, (B) translation by (-a) in s domain, (C) multiplication by e-as in s domain, (D) none of the above, (E) , Leave your comments or Download question paper. Previous question Next question


Q1.	In Laplace transform, multiplication by e^-at in time domain becomes
A.	translation by a in s domain [Correct Answer]
B.	translation by (-a) in s domain [Wrong Answer]
C.	multiplication by e^-as in s domain [Wrong Answer]
D.	none of the above [Wrong Answer]
View Answer 2 -1 Explanation:- Answer : A Discuss it below : !! OOPS Login [Click here] is required to post your answer/result Help other students, write article, leave your comments

Previous question Next question

Also Read Similar Questions Below :

⇒ In the below figure the rms voltage across each half of secondary is 200 V. The peak inverse voltage across each of thyristor
200 V
2(200) V
2(400) V
800 V

⇒ In figure, the power associated with 3 A sourc
36 W
24 W
16 W
8 W

⇒ A JFET operates in ohmic region when
V_GS = 0
V_GS is less than pinch off voltage
V_GS = is Positive
V_GS = V_DS

⇒ In the given figure the reflection coefficient at source en
1
-1
42738
-1/3

⇒ For a standard 2nd order system the maximum overshoot is 10% to an unit step input. If the magnitude of the input is doubled, then maximum overshoot and percentage of maximum overshoot is:
maximum overshoot doubles and percentage of maximum overshoot is less than double
maximum overshoot doubles and percentage of maximum overshoot do not change
maximum overshoot remain same and percentage of maximum overshoot is double
maximum overshoot more than double and percentage of maximum overshoot is less than double

⇒ Ultra high frequency oscillators work in the range
20 Hz to 20 kHz
1 kHz to 30 kHz
30 kHz to 30 MHz
above 30 MHz

⇒ One limitation of constant k filters is that Z₀ is not constant in the pass band.
TRUE
FALSE

⇒ In a N-P-N transistor, when emitter junction is forward biased and collector junction is reverse biased the transistor will operate in
active region
saturation region
cut-off region
inverted region

⇒ In 8085, to disable the whole interrupt system (except TRAP)
the DI instruction may be used
the DO instruction may be used
the INTERRUPT instruction may be used
the El instruction may be used

⇒ Almost all high level languages have provision for logical operations.
TRUE
FALSE

⇒ Given figure shows a 90° sector of spherical reflector with vertex 'V', centre of curvature 'C' and equal distances VD, DF, FE and EC. When a beam of EM wave is incident parallel to the axis, all the energy will pass through the reg
VD
DF
EF
EC

⇒ An RC driving point impedance function has zeros at s = - 2 and s = - 5. The admissible poles are
s = 0 and s = -6
s = -1 and s = -3
s = 0 and s = -1
s = -3 and s = -4

⇒ Which of the following cannot be used to demodulate SSB?
Complete phase shift generator
Product detector
Diode balanced modulator
Bipolar transistor balanced modulator

⇒ In telephone systems the relation between load r, number of calls initiated during a specified interval λ and average duration of a call (h) is
r = λh
r = λh²
λ = rh
h = λr

⇒ An MTI radar operating at 5 GHz has a PRF of 800 pps. The lowest blind speed is
48 m/s
96 m/s
192 m/s
24 m/s

⇒ In a sine wave, maximum rate of change of voltage occurs at
ascent of the waveform
+ ve maximum
- ve maximum
between maximum and minimum

⇒ IC 7485 cannot be cascaded.
TRUE
FALSE

⇒

Assertion (A): A rectifier with inductor filter is more efficient for high load current.

Reason (R): In rectifier with inductor filter we can use a larger choke to reduce ripple, larger choke will have higher dc resistance which will result in lower dc output voltage for higher load current.

Both A and R are individually true and R is the correct explanation of A
Both A and R are individually true but R is not the correct explanation of A
A is true but R is false
A is false but R is true

⇒ Resonant circuits are used in
audio amplifiers
RF amplifiers
both audio and RF amplifiers
none of the above

⇒ A signal g(t) = A then g(t) is a
energy signal
power signal
neither energy nor power signal
insufficient data

⇒ The function of blend control in stereo system is
to dilute left channel
to dilute right channel
to dilute any of the channels
none of the above

⇒ For formation of state equations, resistance of the circuit
should be in tree
should be in cotree
may be in tree or cotree
none of the above

⇒ Two sinusoidal waves 1 and 2 have peak values V_m1 and V_m2. Wave 1 is leading wave 2 by ∠θ. Which of the following is correct?
v₁ = V_m1 sin θ and v₂ = V_m2 cos θ
v₁ = V_m1 sin ωt and v₂ = V_m2 sin (ωt - θ)
v₁ = V_m1 sin (ωt + θ/2) and v₂ = V_m2 sin ωt
none of the above

⇒ For the shaded area in Venn diagram of the given figure, the Boolean expressio
AB + BC + CA
ABC + A B C
ABC + A B C
ABC+AB

⇒

Assertion (A): Magnetic susceptibility of diamagnetic materials is much less than that of paramagnetic materials.

Reason (R): For diamagnetic as well as paramagnetic materials, μ_r is nearly equal to 1.

Both A and R are true and R is correct explanation of A
Both A and R are true but R is not correct explanation of A
A is true but R is false
A is false but R is true

⇒ Consider the following reasons for using antenna coupler

To prevent illegal radiation of spurious frequencies
To tune out reactive components of antenna impedance
To have correct value of load impedance for transmitter.

Which of the above are correct?
1, 2, 3
1, 2
1 only
2, 3

⇒

Match the following:

	List I (Power device)		List II (Max. frequency)
A.	Power Bipolar	1.	MHz
B.	Power MOSFET	2.	100 kHz
C.	SCR	3.	10 kHz
D.	Insulated gate bipolar transistor	4.	1 kHz

A-2, B-1, C-3, D-4
A-3, B-4, C-2, D-1
A-3, B-1, C-4, D-2
A-4, B-1, C-3, D-2

⇒

Assertion (A): The reverse current in a p-n junction is nearly constant.

Reason (R): The reverse breakdown voltage of a p-n diode depends on the extent of doping.

Both A and R are true and R is correct explanation of A
Both A and R are true but R is not a correct explanation of A
A is true but R is false
A is false but R is true

⇒ The number of cells in a 4 variable K map is
16
8
4
32

⇒ The electrochemical equivalent of a material
depends on its valency
depends on its atomic weight
depends on its valency and atomic weight
depends on the degree of hardness of the material