Question is ⇒ In CE configuration, the output characteristics of a bipolar junction transistor is drawn between, Options are ⇒ (A) IC and VCB, (B) IE and VCB, (C) IC and VCE, (D) IE and VCE, (E) , Leave your comments or Download question paper.

Question is ⇒ In CE configuration, the output characteristics of a bipolar junction transistor is drawn between, Options are ⇒ (A) IC and VCB, (B) IE and VCB, (C) IC and VCE, (D) IE and VCE, (E) , Leave your comments or Download question paper. Previous question Next question


Q1.	In CE configuration, the output characteristics of a bipolar junction transistor is drawn between
A.	I_C and V_CB [Wrong Answer]
B.	I_E and V_CB [Wrong Answer]
C.	I_C and V_CE [Correct Answer]
D.	I_E and V_CE [Wrong Answer]
View Answer 1 -1 Explanation:- Answer : C Discuss it below : !! OOPS Login [Click here] is required to post your answer/result Help other students, write article, leave your comments

Previous question Next question

Also Read Similar Questions Below :

⇒ Bandwidth for practical PCM system is (where n is no. of channels, N length of PCM codes)
2n N f_m Hz
4n f_m Hz
2n f_m
(N + 1)f_m

⇒ A transmission line of characteristic impedance z₀ = 50 Ω. Phase Velocity = 2 x 10⁸ m/sec, and length l = 1 m is terminated by a load z₁ = (30 - j 40) ohms. The input impedance of the line for a frequency of 100 MHz will be
(30 + j x 40) Ω
(30 - j 40) Ω
(50 + j x 40) Ω
(50 - j 40) Ω

⇒ A trimmer is basically a
insulator
inductor
capacitor
variable resistor

⇒ For the DAC in the given figure V_{O10 V
5 V
4 V
8 V}

⇒ In figure the output V₀
2V₁ + V₂ - 2V₃
2(V₁ + V₂) - V₃
V₁ + V₂ + V₃
V₁ + 2V₂ - V₃

⇒ In controlled heating circuits, thyristors act as
rectifier
inverter
ac regulator
chopper

⇒ If the peak transmitted power in a radar is increased by a factor 81, the maximum range is increased by a factor of
3
9
27
81

⇒ In a transistor β_dc is likely to vary between 100 and 400. The proper value of β_dc to be used to located Q point is
100
400
250
200

⇒

Assertion (A): A GTO circuit is more compact than SCR circuit

Reason (R): A GTO can be turned off by negative gate pulse.

Both A and R are correct and R is correct explanation of A
Both A and R correct but R is not correct explanation of A
A is correct but R is wrong
A is wrong but R is correct

⇒ Radiation intensity does not depend upon
the antenna direction
antenna width
both (a) and (b)
none of the above

⇒ Heating effect of current is used in
ammeters
voltmeters
both ammeters and voltmeters
wattmeters

⇒ Most of the transistor data sheets specify the power rating for an ambient temperature of
10°C
25°C
50°C
75°C

⇒ The circuit in figur
positive clamper
negative clamper
positive peak clipper
negative peak clipper

⇒ A balanced modulator circuit uses
two identical diodes with same V-I characteristics
two triodes with different V-I characteristics
two diodes with different V-I characteristics
a diode and a triode

⇒ PROM is
Permanent Read Only Memory
Polarized Read Only Memory
Positive Read Only Memory
Programmable Read Only Memory

⇒ A microprocessor with a 16-bit address bus is used in a linear memory selection configuration (i.e., Address bus lines are directly used as chip selects of memory chips) with 4 memory chips. The maximum addressable memory space is
64 K
16 K
8 K
4 K

⇒ When the gate terminal of MOSFET is positive, it is said to operate in
depletion mode
conduction mode
enhancement mode
none of the above

⇒ For wired AND connection we should use
TTL gates with active pull up
TTL gates with open collector
TTL gates without active pull up and with open collector
any of the above

⇒ A computer monitor uses 180 W in normal operation and 20 W in sleep mode. The computer is on all the 24 hours but is in sleep mode for 18 hours a days. The energy units saved in 30 days are
0.54 units
86.4 units
2.88 units
4.8 units

⇒ Maximum usable frequency is [f_muf]
f_c sec i
f_c cos i
f_c sin i
f_c sec i

⇒ If f₁ (t) and f₂ (f) are two functions of time and a and b are constants, then
L [af₁(t) + bf₂(t)] = aF₁(s) + bF₂(s)
L [af₁(t) + bf₂(t)] = aF₁(s) - bF₂(s)
L [af₁(t) + bf₂(t)] =[aF₁(s)]/[bF₂(s]
None of the above

⇒ The r.m.s. value of a half-wave rectified current is 100 A. Its value for full-wave rectification would be __________ amperes.
141.4
200
200/p
40/p

⇒

Assertion (A): PIN diode is commonly used for microwave control.

Reason (R): A PIN diode uses heavily doped p and n materials.

Both A and R are correct and R is correct explanation of A
Both A and R are correct but R is not correct explanation of A
A is correct but R is wrong
A is wrong but R is correct

⇒

Assertion (A): CRT is the most important component of a CRO.

Reason (R): When an electron beam strikes the screen of CRT, a spot of light is produced.

Both A and R are true and R is correct explanation of A
Both A and R are true but R is not correct explanation of A
A is true R is false
A is false R is true

⇒ A computer program is used to read M and print the sum 2 + 4 + 6 + 8 +.........+ 2M. If M = 9 , the print out will show the number
9
18
90
100

⇒ In monolithic ICs, all the components are fabricated by
diffusion process
oxidation
evaporation
none

⇒ An alternating current or voltage is that which
changes in magnitude only
changes in direction only
both (a) and (b)
has a random movement of electrons

⇒ Power gain of antenna equals directive gain in VHF and UHF range if and only if efficiency of the antenna is
0.25
0.5
0.75
1

⇒ A periodic voltage has following value for equal time intervals changing suddenly from one value to next... 0, 5, 10, 20, 50, 60, 50, 20, 10, 5, 0, -5, -10 etc. Then rms value of the waveform is
31 V
32 V
insufficient data
none of these

⇒ Which of the following is λ/2 length?
Marconi
Hertz
Parabolic
Yagi-uda