Question is ⇒ In FM and AM the ratio of signal to noise ratio at the detector output least depends upon, Options are ⇒ (A) bandwidth, (B) transmission, (C) carrier frequency, (D) modulating frequency, (E) , Leave your comments or Download question paper.

Question is ⇒ In FM and AM the ratio of signal to noise ratio at the detector output least depends upon, Options are ⇒ (A) bandwidth, (B) transmission, (C) carrier frequency, (D) modulating frequency, (E) , Leave your comments or Download question paper. Previous question Next question


Q1.	In FM and AM the ratio of signal to noise ratio at the detector output least depends upon
A.	bandwidth [Wrong Answer]
B.	transmission [Wrong Answer]
C.	carrier frequency [Correct Answer]
D.	modulating frequency [Wrong Answer]
View Answer 1 -1 Explanation:- Answer : C Discuss it below : !! OOPS Login [Click here] is required to post your answer/result Help other students, write article, leave your comments

Previous question Next question

Also Read Similar Questions Below :

⇒ The disadvantage of FM over AM is that
high output power is needed
high modulating power is needed
noise is very high for high frequency
large bandwidth is required

⇒ Typical values of voltage gain for CE, CB and CC amplifiers are
100, 100 and 1 respectively
100, 1 and 100 respectively
100, 1 and 1 respectively
1, 100 and 100 respectively

⇒ In saturation region JFET acts like a
bipolar device
short circuit
switch
resistance

⇒ The frequency of the driving network connected between pins 1 and 2 of a 8085 chip must be
equal to the desired clock frequency
twice the desired clock frequency
four times the desired clock frequency
eight times the desired clock frequency

⇒ The reading of the voltmeter in figure will be __________ v
100
150
zero
200

⇒

Assertion (A): Transient periods are of short duration but can result in dangerously high voltages and currents.

Reason (R): Circuit equations in transient analysis are integral differential equations.

Both A and R are correct and R is correct explanation of A
Both A and R are correct but R is not correct explanation of A
A is true, R is false
A is false, R is true

⇒ K maps can be drawn
only for 2 variables
only for 3 variables
only for 4 variables
for any number of variables

⇒

Match the following:

	List I		List II
A.	CLP	1.	Measure of μP clock speed
B.	SHELL	2.	Double sided double density
C.	DSDD	3.	Allows you to specify file as command processor
D.	Megahertz	4.	Microcode stored in ROM

A-4, B-3, C-2, D-1
A-3, B-4, C-2, D-1
A-1, B-2, C-3, D-4
A-2, B-3, C-4, D-1

⇒ In a D-type latch EN = 1, D = 1, the O/P is
1
0
don't care
blocked

⇒ The maximum power handling capacity of a resistor depends on
total surface area
resistance value
thermal capacity of the resistor
resistivity of the material used in the resistor

⇒ Self bias is an example of __________ feedback that tends to stabilize the drain current against changes in temperature and JFET replacement.
variable
low
negative
positive

⇒ Free electrons exist in
first band
second band
third band
conduction band

⇒ In figure gain bandwidth produc
200 Hz
200 MHz
200 kHz
2 MHz

⇒ One of the advantages of base modulation over collector modulation in a class C transistor amplifier is
higher efficiency
more linear operation
more power output per transistor
lesser requirement of modulating power

⇒ Which of the following contributes to harmonics distortion in amplifiers?
Positive feedback
Presence of noise
Defective active device
Non-linearity in active device

⇒ Reluctivity is analogous to
permeability
conductivity
resistivity
retentivity

⇒ Consider the following statements about instrument landing system of aircraft

It ensures correct landing under conditions of low visibility.
It consists of runaway localizer, glide path equipment and marker beacons.
It is basically a blind landing system.

Which of above statements are correct?
All
1 and 2 only
1 and 3 only
2 only

⇒

Match the following:

	List I		List II
A.	shift Register	1.	Frequency division
B.	Counter	2.	Addressing in memory chips
C.	Decoder	3.	Serial to parallel Data conversion

A-3, B-2, C-1
A-3, B-1, C-2
A-2, B-1, C-3
A-1, B-2, C-2

⇒ Barkhausen criterion is 1 + A_vβ = 0.
TRUE
FALSE

⇒

Assertion (A): In a BJT, the base region is very thick.

Reason (R): In p-n-p transistor most of holes given off by emitter diffuse through the base.

Both A and R are true and R is correct explanation of A
Both A and R are true but R is not a correct explanation of A
A is true but R is false
A is false but R is true

⇒ A CE amplifier has r_e = 6 Ω, β = 100 and a = 0.98. The input impedance is
6 Ω
100 Ω
600 Ω
98 Ω

⇒ A series RLC circuit has a resonance frequency of 1 kHz and a quality factor Q = 100. If each of R, L and C is doubled from its original value, the new Q of the circuit is
25
50
100
200

⇒ The h parameter h₁₁ is the same in CE and CC circuit.
TRUE
FALSE

⇒ A single phase energy meter operates on induction principle.
TRUE
FALSE

⇒ Figure shows a Wheatstone bridge with RTD to one arm. If resistance of RTD = 1020 Ω, the voltage V₀
49 mV
51 mV
48 mV
45 mV

⇒ Twelve 1 Ω resistance are used as edges to form a cube. The resistance between two diagonally opposite corners of the cube is
5/6 Ω
1 Ω
6/5 Ω
3/2 Ω

⇒ In metals the valence electron wave functions are strongly perturbed by the presence of neighbouring atoms.
TRUE
FALSE

⇒ An ac circuit has an impedance of (3 + j6) ohm for fundamental. The impedance for fifth harmonic is
(15 + j 30) Ω
(15 + j 6) Ω
(3 + j 30) Ω
(3 + j 1.2) Ω

⇒

Assertion (A): In drawing an electric circuit analogous to a mechanical circuit, spring is replaced by capacitance.

Reason (R): The behaviour of a spring and capacitor are similar.

Both A and R are true and R is correct explanation of A
Both A and R are true and R is not the correct explanation of A
A is true but R is false
A is false but R is true

⇒ In figure, the position of voltmeter and ammeter are exchanged. It may result in damage
both the instruments
ammeter
voltmeter
neither of two