Question is ⇒ In figure the zener has a resistance of 5 ohms. As the load resistance is varied, the output vol, Options are ⇒ (A) will remain constant at 12 V, (B) will vary between 12.05 and 12.65 V, (C) will vary from 10 to 20 V, (D) will remain constant at 12.05 V, (E) , Leave your comments or Download question paper.

Question is ⇒ In figure the zener has a resistance of 5 ohms. As the load resistance is varied, the output vol, Options are ⇒ (A) will remain constant at 12 V, (B) will vary between 12.05 and 12.65 V, (C) will vary from 10 to 20 V, (D) will remain constant at 12.05 V, (E) , Leave your comments or Download question paper. Previous question Next question


Q1.	In figure the zener has a resistance of 5 ohms. As the load resistance is varied, the output vol
A.	will remain constant at 12 V [Wrong Answer]
B.	will vary between 12.05 and 12.65 V [Correct Answer]
C.	will vary from 10 to 20 V [Wrong Answer]
D.	will remain constant at 12.05 V [Wrong Answer]
View Answer 1 -1 Explanation:- Answer : B Discuss it below : !! OOPS Login [Click here] is required to post your answer/result Help other students, write article, leave your comments

Previous question Next question

Also Read Similar Questions Below :

⇒ Tropospheric mode of propagation is used in
UHF
VLF
MF
HF

⇒ If the iron core of a coil is removed so that it becomes an air cored coil, its inductance
will increase
will decrease
will remain the same
may increase or decrease

⇒ The characteristic impedance of a cable is about
300 Ω
50 Ω
5 Ω
2 Ω

⇒ In a full wave rectifier circuit using centre tapped transformer, the peak voltage across half of the secondary winding is 30 V. Then PIV is
30 V
60 V
15 V
10 V

⇒ What will be maximum input that can be converted for a 6 bit dual slope A/D converter uses a reference of -6v and a 1 MHz clock. It uses a fixed count of 40 (101000).
9 V
9.45
10 V
8 V

⇒

Assertion (A): CRO can be used to study waveshape accurately.

Reason (R): Input impedance of a CRO is very high.

Both A and R are true and R is correct explanation of A
Both A and R are true but R is not correct explanation of A
A is true R is false
A is false R is true

⇒

Assertion (A): Master slave JK flip flop is commonly used in high speed synchronous circuitry

Reason (R): Master slave JK flip flop uses two JK flip flops in cascade.

Both A and R are correct and R is correct explanation of A
Both A and R are correct but R is not correct explanation of A
A is true, R is false
A is false, R is true

⇒

Assertion (A): A PROM is a user programmable ROM.

Reason (R): After programming PROM behaves like ROM.

Both A and R are correct and R is correct explanation of A
Both A and R are correct but R is not correct explanation of A
A is correct R is wrong
A is wrong R is correct

⇒ In a CE amplifier circuit the ac voltage between emitter and ground
is very high
may be high or low
is zero
depends on circuit configuration

⇒ DC servomotors are, generally
permanent magnet dc motors
shunt field motors
separately excited dc motors
none of the above

⇒ The power in the signal s(t) = 8 cos (20 p - p/2) + 4 sin (15 pt) is
40
41
42
82

⇒ If input frequency is 50 Hz, the frequency of output wave in a full wave diode rectifier circuit is
25 Hz
50 Hz
100 Hz
200 Hz

⇒ The basic amplifier in Weinbridge oscillator consists of
CE stage followed by CE
CE stage followed by CB
CB stage followed by CE
CC stage followed by CE

⇒ Consider the equation s² + 2s + 2 + K(s + 2) = 0. Where do the roots of this equation break on the root loci plot?
-3.414
-2.414
-1.414
-0.414

⇒ The total number of pins in 8085 are
20
30
40
50

⇒ The circuit shown in the figure conv
BCD to Binary code
Binary to excess - 3 code
Excess - 3 to Gray
Gray to Binary

⇒

Assertion (A): In hot wire instrument the material of hot wire in generally platinum iridium.

Reason (R): A hot wire ammeter is suitable for ac only

Both A and R are true and R is correct explanation of A
Both A and R are true but R is not correct explanation of A
A is true R is false
A is false R is true

⇒ If γ = (S₀/N₀)/(S_i/N_m) where S₀ and S₁ are signal power output and signal power input and N₀ and N_m are noise power output and noise power input, the value of γ for SSB-SC and DSB-SC amplitude modulated system respectively are
1 and 1
1 and 2
2 and 1
0.5 and 0.5

⇒ Hall effect is observed in a specimen (metal or semi- conductor) when it is carrying current and is placed in a magnetic field. The resultant electric field inside the specimen is
normal to both current and magnetic field
in the same direction as current
in a direction anti parallel to magnetic field
none of the above

⇒ Decimal 18.29 when converted int 10's complement will become
81.7707
81.7
81.777
81.077

⇒ The language PL / I has
one character set having 60 characters
one character set having 48 characters
one character set having 60 characters and another character set having 48 character
none of the above

⇒ In figure V_BE = 0.7 V. The base curren
above 97 μA
about 97 mA
about 75 μA
about 75 mA

⇒ Find value
1A
0A
0.45 A
None of these

⇒ An RLC series circuit has R = 8 Ω, X_L = 8 Ω and X_C = 8 Ω Its impedance is
8 + j 16 Ω
8 + j 8 Ω
8 Ω
24 Ω

⇒ A pulse train can be delayed by a finite number of clock periods by using
serial in-serial out shift register
parallel in serial out shift register
serial in-parallel out shift register
parallel in parallel out shift register

⇒ IF amplifiers for radio receivers are often tuned to
456 Hz
456 kHz
3456 MHz
456 GHz

⇒ Magnetic effect of current is used in
ammeters
voltmeters
wattmeters
ammeters, voltmeters, wattmeters and energy meters

⇒ RC network shown in the given figure can provide a maximum theoretical phase shif
90°
180°
270°
360°

⇒ The power dissipated per gate
is constant at all frequencies
increases with frequency
decreases with frequency
may increase or decrease with frequency

⇒ A balanced modulator is used in the generation of which of the following?
DSB-SC signal
FM signal
PM signal
PAM signal