Question is ⇒ In figure v1 = 8 V and v2 = 8 V. Which diode will cond, Options are ⇒ (A) D1 only, (B) D2 only, (C) Both D1 and D2, (D) Neither D1 nor D2, (E) , Leave your comments or Download question paper.

Question is ⇒ In figure v1 = 8 V and v2 = 8 V. Which diode will cond, Options are ⇒ (A) D1 only, (B) D2 only, (C) Both D1 and D2, (D) Neither D1 nor D2, (E) , Leave your comments or Download question paper. Previous question Next question


Q1.	In figure v₁ = 8 V and v₂ = 8 V. Which diode will cond
A.	D₁ only [Wrong Answer]
B.	D₂ only [Wrong Answer]
C.	Both D₁ and D₂ [Correct Answer]
D.	Neither D₁ nor D₂ [Wrong Answer]
View Answer 1 -1 Explanation:- Answer : C Discuss it below : !! OOPS Login [Click here] is required to post your answer/result Help other students, write article, leave your comments

Previous question Next question

Also Read Similar Questions Below :

⇒ The difference between resonant commutation and self commutation is
both these methods are based on entirely different principles
in resonant commutation, the commutating elements carry load current but in self commutation, the commutating elements do not carry load current
resonant commutation uses L and C but self commutation uses only capacitor
none of the above

⇒ A single phase half wave rectifier is feeding a resistive load. As firing angle is increased
dc output voltage and rms output voltage decrease in the same proportion
dc output voltage and rms output voltage decrease
dc output voltage and rms output voltage increase
dc output voltage and rms output voltage increase in the same proportion

⇒

Assertion (A): The forward resistance of a p-n diode is not constant.

Reason (R): The v-i characteristics of p-n diode is non-linear.

Both A and R are true and R is correct explanation of A
Both A and R are true but R is not a correct explanation of A
A is true but R is false
A is false but R is true

⇒ When a thyristor is conducting, the voltage drop across it is about
1 V
10 V
100 V
0.1 V

⇒ The figures shows the symbo
p channel depletion MOSFET
p channel enhancement MOSFET
complementary MOSFET
p channel JFET

⇒

Match the following:

	List I (BHE, A0)		List II (Word is read/write)
A.	0, 0	1.	1 byte from/to odd address
B.	0, 1	2.	1 byte from/to even address
C.	1, 0	3.	16 bit word
D.	1, 1	4.	None

A-1, B-2, C-3, D-4
A-3, B-1, C-2, D-4
A-2, B-3, C-4, D-1
A-4, B-1, C-2, D-3

⇒ In pulse width modulation of chopper
T is kept constant and T_on is varied
T_on is kept constant T is varied
both T and T_on are varied
either T or T_on is varied

⇒ Two CE stages are coupled through a capacitor. To calculate the quiescent base current of the two transistors, the capacitor is treated as
open circuit
short circuit
neither (a) nor (b)
either (a) or (b)

⇒ The K-map for a Boolean function is shown in figure. The number of essential prime implicants for this functio
4
5
6
8

⇒ In figure, capacitor is uncharged. The switch is closed at t = 0 at t = 0⁺ di/dt100 A/s
-100 A/s
1000 A/s
-1000 A/s

⇒ Which one of the following statements regarding compandor is FALSE?
It compresses the higher-amplitude parts of a signal before modulation and expands them back to normal again after demodulation.
It gives preferential treatment to the weaker parts of the signal
For weaker signals it gives a poor ratio of signal strength to quantizing error
Weaker signals, traverse more quantum steps than they would do otherwise and so quantizing error is reduced.

⇒ Consider the following stateme
1 and 2 only
1, 2 and 4
2 and 3 only
2, 3 and 4

⇒ Shaft encoder is used to measure
angular position
linear position
linear velocity
linear acceleration

⇒ In 8355, the ROM is organized as __________ words of 8 bits each.
2000
2048
8355
835

⇒ A circuit is fed by two sources of the same frequency and values 100 ∠0° V and 20 ∠30°V. The current in a particular branch is 5 ∠19° A. If the magnitudes of the sources and changed to 200 ∠0° V and 40 ∠30° V, the current in that branch should be
5 ∠19° A
10 ∠19° A
10 ∠38° A
10 ∠9.5° A

⇒ The residual resistivity of a binary alloy at 0°K is
the sum of the residual resistivities of the component metals
the difference of the residual resistivities of the component metals
the product of the residual resistivities of the component metals
depend on the concentration of the minor component in the alloy

⇒ In figure the trace on the CRO wil
half rectifier wave
clamped wave
no trace at all
either (a) or (b)

⇒ A string of series connected thyristors needs equalising circuit to
ensure proper firing
ensure proper current division
ensure proper voltage division
none of the above

⇒ A reactance function
has a pole at origin
has a zero at origin
may have a pole or zero at origin
has a pole or zero at origin and a pole or zero at infinity

⇒ Which of the following is an oscillator with best frequency stability?
Crystal oscillator
Clapp oscillator
Phase shift circuit
Multivibrator

⇒ A carrier is simultaneously modulated by two sine waves having modulation indices of 0.4 and 0.3. The total modulation index will be
0.1
0.7
0.5
0.35

⇒ In VHS format the width of tape is
2"
1"
1/2"
1/4"

⇒ The relative stability of a system is given by
gain margin alone
phase margin alone
both phase and gain margins
either (a) or (b)

⇒ Consider the following statements as regards BPSK and QPSK:
In BPSK we deal individually with each bit of duration T_b
In QPSK we lump two bits to form a symbol
In both BPSK and QPSK signal changes occur at bit rate
In QPSK the symbol can have any one of four possible values
Which of the above statements are correct?
1, 2, 3, 4
1, 2, 3
1, 2, 4
2, 3, 4

⇒ What is the period of the sinusoidal signal x(n) = 5 cos [0.2 pn]?
10
5
1
0

⇒ TTL circuit with active pull up is preferred because of its suitability for
wired AND operation
bus operated system
wired logic operation
reasonable dissipation and speed of operation

⇒ The V_TH at terminals A and B is equal
0 V
5 V
- 5 V
None of these

⇒ FM amplifier in a superheterodyne receiver
increases selectivity
suppresses noise
provides improved tracking
improves the rejection of the image frequency

⇒ In practical commercial AM system channel bandwidth is
150 kHz
100 kHz
15 kHz
200 kHz

⇒ The bandwidth of an amplifier can be reduced by
miller effect compensation
pole zero compensation
dominant pole compensation
lead compensation

Users Also Read
Previous Papers

Aptitude

Reasoning

Gen.Knowledge

Speak English

English / Verbal

Online / Mock Test

Vedic Math