Question is ⇒ In D-type FF, Preset (Pr) and clear (Clr) inputs are called, Options are ⇒ (A) Synchronous, (B) Asynchronous, (C) Data, (D) None, (E) , Leave your comments or Download question paper.

Question is ⇒ In D-type FF, Preset (Pr) and clear (Clr) inputs are called, Options are ⇒ (A) Synchronous, (B) Asynchronous, (C) Data, (D) None, (E) , Leave your comments or Download question paper. Previous question Next question


Q1.	In D-type FF, Preset (Pr) and clear (Clr) inputs are called
A.	Synchronous [Wrong Answer]
B.	Asynchronous [Correct Answer]
C.	Data [Wrong Answer]
D.	None [Wrong Answer]
View Answer 1 -1 Explanation:- Answer : B Discuss it below : !! OOPS Login [Click here] is required to post your answer/result Help other students, write article, leave your comments

Previous question Next question

Also Read Similar Questions Below :

⇒ A parallel resonant circuit can be used
as a high impedance
to reject a small band of frequencies
both (a) and (b)
to amplify certain frequencies

⇒ In a reflex klystron the output frequency is determined primarily by resonant frequency of cavity.
TRUE
FALSE

⇒ The length of half-wave antenna is at 30 MHz
2.5 meter
5 meter
10 meter
100 meter

⇒ Which of the following microphones is used as a standard for calibration?
Moving coil
Carbon
Condenser
Ribbon

⇒ When the number of quantising levels is 16 in PCM, the number of pulses in a code group will be
3
4
8
16

⇒

Assertion (A): The sign and magnitude of displacement can be measured by an LVDT.

Reason (R): LVDT is based on the principle of mutual inductance.

Both A and R are true and R is correct explanation of A
Both A and R are true but R is not correct explanation of A
A is true R is false
A is false R is true

⇒

Assertion (A): Thermocouple instruments can be used for ac only.

Reason (R): Thermocouple instrument has a non linear scale.

Both A and R are true and R is correct explanation of A
Both A and R are true but R is not correct explanation of A
A is true R is false
A is false R is true

⇒

Match the following:

	List I		List II
A.	shift Register	1.	Frequency division
B.	Counter	2.	Addressing in memory chips
C.	Decoder	3.	Serial to parallel Data conversion

A-3, B-2, C-1
A-3, B-1, C-2
A-2, B-1, C-3
A-1, B-2, C-2

⇒ In figure, the curre
is 2 A from A to B
is 2 A from B to A
depends on the value of R
none of the above

⇒ It is desired to reduce the reflection at an air porcelain by use of 7/4 plate (for Porcelain μ = 40, and ε_r = 7). The thickness of the polystyrene plate required at 10 GHz will be
5.039 cm
50.39 cm
0.5039 cm
0.05039 cm

⇒ The problem of logic race occurs in
SOP functions
POS functions
Hybrid function
SOP and POS functions

⇒ The bandwidth of DSB suppressed carrier modulation system when the modulating frequency varies between 500 Hz and 5 kHz is
555 kHz
505 kHz
500 kHz
9 kHz

⇒ The modulation index is, if f_m = 500 Hz, Δf = 2.25 kHz
2.25
4.5
9
18

⇒ A dc separately excited motor has constant field current. The armature is fed from a single phase supply through a full converter. When a = 0, speed is 500 rpm. If a = 45°, the speed is likely to be
about 350 rpm
about 250 rpm
about 175 rpm
about 125 rpm

⇒ The quiescent collector current I_C, and collector to emitter voltage V_CE in a CE connection are the values when
ac signal is zero
ac signal is low
ac signal is negative
either (a) or (b)

⇒ Polar plot of a lag-lead compensator is a circle.
TRUE
FALSE

⇒ Choose correct option for a stable system :

Roots of the characteristic equation of the system are real and negative
Area within the impulse response is finite

I is true, II is true
I is true, II is false
I is false, II is true
I is false, II is false

⇒ In a 3 phase semiconverter, the firing frequency is
equal to line frequency
3 times the line frequency
6 times the line frequency
12 times the line frequency

⇒ Logic hardware is available only in NAND and NOR.
TRUE
FALSE

⇒

Match the following:

	List I		List II
A.	Reactance theorem	1.	Foster
B.	Driving point impedance	2.	Bartlett
C.	Continued fraction expansion	3.	Cauer
D.	Bisection Theorem	4.	Positive real function

A-1, B-4, C-3, D-2
A-1, B-2, C-3, D-4
A-2, B-3, C-1, D-4
A-3, B-4, C-2, D-1

⇒ When a unit step voltage drives a lag network the output
remains constant at unit step value
increases exponentially from zero to final value
decreases exponentially from 1 to 0
either (b) of (c) depending on values of R and C

⇒ For an RC admittance function
the lowest critical frequency is a zero
the highest critical frequency is a pole
the lowest critical frequency is zero and the highest critical frequency is a pole
the lowest critical frequency is a pole

⇒ The polarities of the magnetised iron rod of
A is N, B is S and C is neutral
A is N, B is S and C is S
A is N, B is N and C is S
A is S, N is S and C is N

⇒ The real part of complex frequency s corresponds to oscillations.
TRUE
FALSE

⇒ The mobility of e^- for Ge and Si respectively is
1.66, 2.5
2.5, 1.66
2.7, 2.33
2.33, 2.7

⇒ Mark out the WRONG statem
Needs very high-speed burst modems
Faces no problems caused by intermodulation of carriers so that transponder can be used at its full power
Needs high-speed manipulation of bit streams
Is less flexible so that channels of widely different capacities cannot used and intermixed

⇒ A p matching network for coupling the transmitter output of the antenna is shown in figu
minimum D.C. plate current
maximum D.C. plate current
maximum RF antenna current
specified value of the D.C. plate current

⇒ In an LC immittance H (s)
the slope of dH (jω)/dω is always negative
the slope of dH (jω)/dω is always positive
the slope of dH (jω)/dω may be positive or negative
the slope of dH (jω)/dω is constant

⇒ In the below figure the rms voltage across each half of secondary is 200 V. The peak inverse voltage across each of thyristor
200 V
2(200) V
2(400) V
800 V

⇒ The derating factor for a BJT transistor is about
0.5 mW/°C
2.5 mW/°C
10 mW/°C
25 mW/°C