Question is ⇒ In control systems the output of sensor usually, is, Options are ⇒ (A) analog electrical signal, (B) digital electrical signal, (C) mechanical signal, (D) analog or digital electrical signal, (E) , Leave your comments or Download question paper.

Question is ⇒ In control systems the output of sensor usually, is, Options are ⇒ (A) analog electrical signal, (B) digital electrical signal, (C) mechanical signal, (D) analog or digital electrical signal, (E) , Leave your comments or Download question paper. Previous question Next question


Q1.	In control systems the output of sensor usually, is
A.	analog electrical signal [Wrong Answer]
B.	digital electrical signal [Wrong Answer]
C.	mechanical signal [Wrong Answer]
D.	analog or digital electrical signal [Correct Answer]
View Answer 2 -1 Explanation:- Answer : D Discuss it below : !! OOPS Login [Click here] is required to post your answer/result Help other students, write article, leave your comments

Previous question Next question

Also Read Similar Questions Below :

⇒ Oscillations are obtained from a reflex klystron only for combinations of anode voltage and repeller voltage that give a favourable transit time.
TRUE
FALSE

⇒ In VHS format width of audio track is
5 mm
2 mm
1 mm
0.1 mm

⇒ If a signal f(t/2) has energy is E/n then energy of the signal f(nt) is equal to __________ (n is constant)
E/2n²
2E/n²
E/n²
2En²

⇒ Audio amplifiers need
Bass control
Treble control
Both Bass and Treble control
Either Bass or Treble control

⇒ The phase margin and damping ratio have no relation.
TRUE
FALSE

⇒ A constant k low pass filter has f_c = 500 Hz. At f = 1000 Hz, the attenuation is
zero
infinity
may be zero or infinity
more than zero but less than infinity

⇒ A dynamometer wattmeter can be used for
dc only
ac only
dc and 50 Hz ac
dc and high frequency ac

⇒ The series element in band pass filter is
capacitive
inductive
parallel combination of inductance and capacitance
series combination of inductance and capacitance

⇒

Assertion (A): The gall tinsley potentiometer is a coordinate potentiometer and has two exactly similar potentiometers.

Reason (R): An ac potentiometer may measure the unknown voltage in polar form or rectangular coordinate form.

Both A and R are true and R is correct explanation of A
Both A and R are true but R is not correct explanation of A
A is true R is false
A is false R is true

⇒ The charges between a hollow and solid metal spheres reside
through out in both
on outer surface in hollow and through out in solid
on the outer surface in both
none of the above

⇒ The bandwidth required for amplitude modulation is
half the frequency of modulating signal
equal to the frequency of modulating signal
twice the frequency of modulating signal
four times the frequency of modulating signal

⇒ Which of the following circuit cannot be used to demodulate SSB?
Phase discriminator
Produce detector
Balanced modulator
Beat frequency oscillator

⇒ An astable multivibrator circuit using IC 555 timer is shown below. Assume that the circuit is oscillating stea
3 V to 5 V
3 V to 6 V
3.6 V to 6 V
3.6 V to 5 V

⇒ The minimum energy of a photon required for intrinsic excitation is equal to
energy of bottom of conduction band
energy of top of valence band
forbidden gap energy
Fermi energy

⇒ A 360 W carrier is simultaneously modulated by two audio wave with modulation percentage of 55 and 65 respectively. Total sideband power radiated will be
500 W
360 W
180 W
130 W

⇒ Zip floppy has a capacity of
50 MB
500 MB
25 MB
100 MB or 250 MB

⇒ The 54/74164 chip is an 8-bit serial-input-parallel-output shift register. The clock is 1 MHz. The time needed to shift a 8-bit binary number into the chip is
1 μs
2 μs
8 μs
16 μs

⇒ In a biased limiter the clipping level can be adjusted by adjusting the voltage of battery.
TRUE
FALSE

⇒ The fuse material used in electrical lines must have which one of the following properties?
High resistivity
Low conductivity
High melting point
Low melting point

⇒ Mutual impedance is not depend upon
magnitude of induced current
tuning condition
self impedance
phase relationship between induced and original currents

⇒ Voice signal band limited to 3.4 KHz is sampled and pulse code modulated using 64 quantization levels. Ten such signals are time division multiplexed using one 5-bit synchronizing word every alternate frame. The minimum channel bandwidth required for transmission of the TDM signal is
100 KHz
200 KHz
50 KHz
150 KHz

⇒ Which of the following has highest power gain?
CE
CC
CB
CB or CC

⇒ The output voltage waveform of a CE amplifier is fed to a dc coupled CRO. The trace on the screen will be
dc output voltage
ac output voltage
sum of dc and ac output voltage
either (a) or (b)

⇒ Which of the following should be used in order to prevent overloading or the last IF amplifier in a receiver?
Variable selectivity
Variable sensitivity
Double conversion
Squelch

⇒ Why does a FM radio station perform better than and AM station radiating the same actual power?
FM is immune to noise
AM has only two sidebands while FM has more
FM uses larger bandwidth for large modulation depth.
Capture effects appears in FM.

⇒

Assertion (A): A demultiplexer can be used as a decoder.

Reason (R): A demultiplexer can be built by using AND gates only.

Both A and R are correct and R is correct explanation of A
Both A and R are correct but R is not correct explanation of A
A is true, R is false
A is false, R is true

⇒ What would be the rms value of a sine wave having the same peak value as that of the above mentioned periodic wave?
42.2 V
19 V
38.2 V
none

⇒

Assertion (A): Industrial robots improve productivity.

Reason (R): Robots can handle monotonous and complex jobs without error in operation.

Both A and R are correct and R is correct explanation of A
Both A and R are correct but R is not correct explanation of A
A is correct but R is wrong
R is correct but A is wrong

⇒ In FM,
there is a large decrease in noise and hence increase in the signal to noise ratio
there is a large increase in noise and hence decrease in the signal to noise ratio
there is a large increase in noise and hence increase in the signal to noise ratio
there is a large decrease in noise and hence decrease in the signal to noise ratio

⇒ Power factor of the following circuit will be unity
inductance
capacitance
resistance
both (a) and (b)