Question is ⇒ In commercial vehicle layouts engine is located forward, rear or under floor mainly to, Options are ⇒ (A) Better utilization of space, (B) Increase fuel economy, (C) Better weight distribution, (D) Reduce the weight of chassis, (E) , Leave your comments or Download question paper.

Question is ⇒ In commercial vehicle layouts engine is located forward, rear or under floor mainly to, Options are ⇒ (A) Better utilization of space, (B) Increase fuel economy, (C) Better weight distribution, (D) Reduce the weight of chassis, (E) , Leave your comments or Download question paper. Previous question Next question


Q1.	In commercial vehicle layouts engine is located forward, rear or under floor mainly to
A.	Better utilization of space [Wrong Answer]
B.	Increase fuel economy [Wrong Answer]
C.	Better weight distribution [Correct Answer]
D.	Reduce the weight of chassis [Wrong Answer]
View Answer 46 -18 Explanation:- Answer : C Discuss it below : !! OOPS Login [Click here] is required to post your answer/result Help other students, write article, leave your comments

Previous question Next question

Also Read Similar Questions Below :

⇒ The unsprung mass in a vehicle system is mainly composed of
The frame assembly
Gear box and propeller shaft
Axle and the parts attached to it
Engine and associated parts

⇒ When we lift a 10 kg weight, 3 metre we would be doing
300 m kg of work
3 m kg of work
30 m kg of work

⇒ A fluid coupling
Acts like flywheel and replaces it since as it is known also by the name fluid wheel
It takes the place of friction clutch and replaces it completely in synchromesh transmission systems
It replaces the friction clutch and the Gearbox also
Does the function of a clutch automatically, but cannot be used for shifting transmission to effect Gear changes

⇒ If we know the engine speed, bore, stroke, number of cylinders and m.e.p in the cylinders, we can calculate
FHP
IHP
BHP

⇒ The conventional motor car has
Two forward speeds
Three forward speeds
Four forward speeds

⇒ The ratio between the speed of the camshaft and the speed of the crankshaft is
1:1
1:4
1:2
1:1/4

⇒ In the slip joint, slippage occurs between internally and externally mated
Couplings
joints
Splines

⇒ In a vehicle with dual rear axle, the wheel base is measured from the
Axis of the front wheel to the nearest rear wheel axis
Axis of the front wheel to the farthest rear wheel axis
Rear of cab to farthest rear wheel axis
Axis of the front wheel to an axis midway between the axes of rear wheels

⇒ Which one of the following is not a trade name of tractor in India
Kirloskar
Escort
Standard
HMT

⇒ The function of a torque converter or fluid converter is similar to that of a
Gear box
Clutch
Shock absorber
Torsion box

⇒ The sun gear in the planetary gear system meshes with the
Pinion cage
Ring gear
Clutch gear
Planet pinions

⇒ In general the design of the current regulator is such that its main actuating winding carries full
Generator voltage
Generator output
Field current
Battery voltage

⇒ In an operating engine, the hottest part of the piston is the
Head
Ring grooves
Skirt
Pin bosses

⇒ Immediately after ignition, combustion chamber temperatures may reach a value of
15000C
55000C
25000C
75000C

⇒ In the transmission system, the provision of slip joints allows a change in the
Angle of drive
Length of shaft
Speed of rotation

⇒ Piston compression rings are manufactured by
Aluminium
Cast iron
Steel
Bronze

⇒ In the hydraulic brake system, movement of a piston in the master cylinder produces hydraulic pressure which causes movement of the
Wheel cylinder pistons
Brake pedal
Brake cam

⇒ The maximum pressure of air fuel mixture at the end of compression in petrol engines varies from
10-30 Kg/cm2 b. 30-100 Kg/cm2
6-10 Kg/cm2
100-1000 Kg/cm2

⇒ The ratio of the cylinder volume at BDC and the clearance volume is called
Clearance ratio
Volumetric ratio
Compression ratio

⇒ The device for smoothing out the power impulses from the engine is called the
Flywheel
Camshaft
Crankshaft
Clutch

⇒ The conventional mechanical type fuel pump develops ............. pressure
0.15 Kg/cm2
1.0 Kg/cm2
0.5 Kg/cm2
0.3 Kg/cm2

⇒ The coil spring clutch may use from
Two to six springs
Three to nine springs
Four to eight springs
Ten to twelve springs

⇒ Clutch slippage while clutch is engaged is particularly noticeable
When starting the engine
During acceleration
During idle
At low speed

⇒ The friction disc is positioned between the flywheel and the
Engine
Crankshaft
Pressure plate

⇒ To correct heavy heel contact on the ring gear teeth, move the
Drive pinion in
Ring gear towards pinion
Ring gear away from pinion and adjust backlash

⇒ The power developed inside the engine cylinder is called
IHP
FHP
BHP

⇒ Two types of antifreeze are
Iso octane and ethylene glycol
Alcohol base and ethylene glycol
Ethylene glycol and propylene glycol

⇒ Connecting rods are generally of the following from
Forged round section steel
Cast steel triangular section
Forged square section steel
Forged I section steel

⇒ X - member of a car frame ensures improved
Resistance to side force due to transverse wind load
Bending strength of side members
Resistance to vertical shock loads acting simultaneously on both front wheels
Resistance of weaving and torsional strength of front end of frame

⇒ Overdrive is provided in the transmission of a vehicle to
Reach higher road speeds
improved fuel consumption
achieve better acceleration
carry more load