Question is ⇒ In cellular telephone each cell is designed to handle, Options are ⇒ (A) 45 two way communications, (B) 90 two way communications, (C) 45 one way communications, (D) 180 two way communications, (E) , Leave your comments or Download question paper.

Question is ⇒ In cellular telephone each cell is designed to handle, Options are ⇒ (A) 45 two way communications, (B) 90 two way communications, (C) 45 one way communications, (D) 180 two way communications, (E) , Leave your comments or Download question paper. Previous question Next question


Q1.	In cellular telephone each cell is designed to handle
A.	45 two way communications [Correct Answer]
B.	90 two way communications [Wrong Answer]
C.	45 one way communications [Wrong Answer]
D.	180 two way communications [Wrong Answer]
View Answer 1 -1 Explanation:- Answer : A Discuss it below : !! OOPS Login [Click here] is required to post your answer/result Help other students, write article, leave your comments

Previous question Next question

Also Read Similar Questions Below :

⇒ Lead becomes a superconductor at
9.1 K
7 K
5 K
3 K

⇒ A number is expressed in binary 2's complement as 10011 decimal equivalent value is
19
13
-19
-13

⇒ In the given figure power meters at A and B indicate 1 mW and 110 μW respectively. VSWR of lin
1.5
2
2.5
3

⇒ For the block diagram of the given figure, the equation describing system dynamic
(1 + RCs) Δθ₀(s) = Δθ_i(s) + R Δ H(s)
(1 + RCs) [ΔH(s)] = Δθ(s) - Δθ₀(s)
(1 + RCs) Δθ₀(s) = RΔ H(s) - Δ θ_i(s)
(1 + RCs) Δθ_i(s) = Δ H(s)[R] - Δθ₀(s)

⇒ In h parameter representation, the independent variables are
I₁ and V₂
I₂ and V₁
V₁ and V₂
I₁ and I₂

⇒ Which of the following devices uses a slow wave structure?
Klystron two cavity amplifier
Klystron multicavity amplifier
Reflex klystron oscillator
TWT

⇒ Geosynchronous satellites are always launched in the equatorial plane because it is the only plane which provides
24-hour orbit
stationary satellite
global communication
zero-gravity environs

⇒ In the transformer shown in the figure, the inductance measured across the terminal 1 and 2 was 4 H with open terminals 3 and 4. It was 3H when the terminals 3 and 4 were short circuited. The coefficient of coupling woul
1
0.707
0.5
indetermine due to insufficient data

⇒ For the logic circuit of the given figure the simplified Boolean expression
A ⊕ B
A + B
AB
A + B

⇒ A lag compensator
speeds up the transient response of the system
improves steady state behaviour of the system
improves steady state behaviour and speeds up the transient response of the system
improves steady state behaviour and preserves the transient response of the system

⇒ A parametric amplifier uses
non linear resistance
non linear reactance
either (a) or (b)
neither (a) nor (b)

⇒ When a UJT is used as a relaxation oscillator the current should be
less than I_p
more than I_v
more than I_p but less than I_v
negative

⇒ The 54/74164 chip is an 8-bit serial-input-parallel-output shift register. The clock is 1 MHz. The time needed to shift a 8-bit binary number into the chip is
1 μs
2 μs
8 μs
16 μs

⇒ The self inductances of two coils are 27 H and 3 H. If the winding or coils is such that 50% of flux of one links the other, the mutual inductance is
30 H
24 H
9 H
4.5 H

⇒ A moving iron instrument can be used for
dc only
ac only
both dc and ac
dc and high frequency ac

⇒ Which of the following transformers has low primary current?
Current transformer
Potential transformer
Distribution transformer
Both (a) and (b)

⇒ The Kirchoff's laws fail in which of the following circuits?
Linear circuits
Non-linear circuits
Lumped parameters circuits
Distributed parameters circuits

⇒ If the input to the ideal comparator shown in the figure is a sinusoidal signal of 8 V (peak to peak) without any DC component, then the output of the comparator has a duty cycl
42737
42738
42741
42747

⇒ Which of the following is a computer language?
MS WORD
Page maker
MS EXCEL
LISP

⇒ In a positive edge triggered JK flip flop, J = 1, K = 0 and clock pulse is rising Q will
be 0
be 1
show no change
toggle

⇒ In an ac network the sum of currents entering a node is 10 ∠45°. The sum of currents leaving the node is
19.32 ∠45°
15 ∠45°
20 ∠45°
zero

⇒ In digital computer programming, subroutines are used
to reduce program execution time at the expense of more memory
to reduce storage requirements
to increase programming ease and reduce storage requirements
because most of the functions are same

⇒ Figure shows basic Hartley oscillator configuration. Do you think the polarities marked for the split coiled are corr
yes they are
no they are not
it really doesn't matter
none of the above

⇒ Consider the following statements about mutual inductances:

The value should remain constant under all conditions.
The mutual inductance should not vary with temperature.
The inductance should be independent of excitation.
They have two coils wound on a bobbin of hard magnetic material, coils being separated by a range.

Out of the above, correct statement are
2, 3, 4
1, 2, 3
1, 3, 4
1, 2, 4

⇒ Which of the following statements regarding two transistor model of p-n-n-p device is correct?
It explain only the turn on portion of the device characteristics
It explain only the turn off portion of the device characteristics
It explain only the negative region portion of the device characteristics
It explain all the regions of the device characteristics

⇒ If N = 196, the result of the following program will be 196
16
16
196

⇒ In a communication receiver, a squelch circuit is normally inserted
before detector
after detector
before mixer
after power amplifier

⇒ For an P-channel enhancement type MOSFET determine the drain current if K = 0.278 x 10^-3A/V², V_GS = -4V, V_T = -2V, Voltage equivalent at 27°C = 26 mV.
10 mA
1.11 mA
0.751 mA
46.98 mA

⇒ If E_b, the energy per bit of a binary digital signal is 10^-6 watt sec. and the one sided power spectral density of the white noise N₀ = 10^-5 W/Hz, then the output SNR of the matched filter is
26 dB
10 dB
20 dB
13 dB

⇒ Consider the following statements

An assembler is a program having assembly language program as input and machine language program as output.
A macro assembler is an assembler with additional macro facilities.
A cross assembler for a μP X is an assembler which executes on source microcomputer with a different CPU than X bit generates code for X.
Assemblers generally do not provide macro facilities.

Of the above statement
All are correct
only 1, 2, 3 are correct
only 1, 2, 4 are correct
only 1, 3, 4 are correct