Question is ⇒ In CC configuration, the output signals has approximately, Options are ⇒ (A) the same amplitude and phase, (B) opposite amplitude and phase, (C) same amplitude but opposite phase, (D) none of the above, (E) , Leave your comments or Download question paper.

Question is ⇒ In CC configuration, the output signals has approximately, Options are ⇒ (A) the same amplitude and phase, (B) opposite amplitude and phase, (C) same amplitude but opposite phase, (D) none of the above, (E) , Leave your comments or Download question paper. Previous question Next question


Q1.	In CC configuration, the output signals has approximately
A.	the same amplitude and phase [Correct Answer]
B.	opposite amplitude and phase [Wrong Answer]
C.	same amplitude but opposite phase [Wrong Answer]
D.	none of the above [Wrong Answer]
View Answer 2 -1 Explanation:- Answer : A Discuss it below : !! OOPS Login [Click here] is required to post your answer/result Help other students, write article, leave your comments

Previous question Next question

Also Read Similar Questions Below :

⇒ Nichols chart consists of
constant magnitude loci
constant phase angle loci
magnitude and phase angle loci in log-magnitude versus phase diagram
none of the above

⇒ LVDT is a
pressure transducer
displacement transducer
velocity transducer
acceleration transducer

⇒ If f₁(t)<< F₁(jω) and f₂(t)↔ F₂(jω), then [a₁ f₁(t) + a₂f₂(t)]↔
a₁F₁(jω) + a₂F₂(jω)
a₁a₂F₁(jω) + F₂(jω)
a₁F₁(jω) - a₂F₂(jω)
a₁F₁*(jω) + a₂F₂*(jω)

⇒ The current I flowing in the branc
-12 A
0
0.125
-3 A

⇒ In microwave communication, some times, microwave signals reach large distances by following the earth curvature. This phenomenon is called
tropospheric scatter
faraday effect
ionospheric reflection
ducting

⇒ The thin parallel wires are carrying current along the same direction. The force experienced by one due to the other is
parallel to the lines
perpendicular to the lines and attractive
perpendicular to the lines and repulsive
zero

⇒ In 8085 microprocessor, what is the length of SP (stack) pointer?
6 bits
8 bits
12 bits
16 bits

⇒ Which of the following is a balanced line?
Coaxial line
Strip line
Microstrip line
TV twin lead

⇒ The drain characteristics of JFET are drawn between
V_GS and V_DS for different values of drain current
drain current and V_GS for different values of V_DS
drain current and V_DS for different values of V_GS
drain current and V_GSfor one value of V_DS

⇒ For very low frequencies, log magnitude for the given figur
0 dB
-3 dB
3 dB
10 dB

⇒ If other parameter are constant, transmission loss at 5 GHz as compared to that at 0.5 GHz is
20 dB more
20 dB less
700 dB more
100 dB less

⇒ Consider the following logical IF statement in Fortran 77 IF (SALT - PEPPER) 11, 11, 13
IF (SALT - PEPPER) 13, 11, 11
IF (SALT - PEPPER) 13, 13, 11
IF (SALT - PEPPER) 11, 13, 13

⇒ Pre-emphasis circuit is used
after modulation
before modulation
before detection
after detection

⇒ The dependent current source shown in given fig
delivers 80W
absorbs 80W
deliver 40W
absorbs 40W

⇒ According to Siegel and Labus, antenna can be treated as
closed transmission line
shorted transmission line
earthed transmission line
opened-out transmission line

⇒ In N-type semiconductor
electrons are majority carriers while holes are minority carriers
electrons are majority carriers while holes are majority carriers
both electrons as well as holes are majority carriers
both electrons as well as holes are minority carriers

⇒ An audio signal (say from 50 Hz to 10000 Hz) is frequency translated by a carrier having a frequency of 10⁶ Hz. The values of initial (without frequency translation) and final (after frequency translation) fractional change in frequency from one band edge to the other are
200 and 1.01
200 and 10.01
200 and 100.1
200 and 200

⇒ An ideal op-amp has
infinite input and output resistance
low input and output resistance
low input and high output resistance
infinite input resistance and zero output resistance

⇒ If 4 in binary system is 100 then 8 will be
10
100
111
1000

⇒ If V_dc1 is the dc output voltage in half wave controlled rectifier circuit feeding resistive load and V_dc2 is the dc output voltage in full wave controlled rectifier circuit (M - 2 connection) feeding resistive load, then
V_dc1 = 0.5 V_dc2 for all values of firing angle
V_dc1 = V_dc2 for all values of firing angle
V_dc1 ≤ 0.5 V_dc2 for all values of firing angle
V_dc1 ≥ 0.5 V_dc2 for all values of firing angle

⇒ The passage of current in an electrolyte is due to the movement of
electrons
molecules
atoms
ions

⇒ The range of life time carriers (electrons and holes) is
1 μs to 100 μs
1 nano sec to 1 μs
1 nano sec to hundreds of μs
none of the above

⇒ In most electric irons, the thermister used for controlling temperature is
vapour-filled bulb
high-expansion steel rod
bimetallic strip
thermopile

⇒ At corner frequency the phase angle of factor 1/(1 + jωT) is
+90°
-90°
+45°
-45°

⇒

Assertion (A): A presettable counter can be preset to any desired starting point

Reason (R): The maximum frequency of a ripple counter depends on the modulus.

Both A and R are correct and R is correct explanation of A
Both A and R are correct but R is not correct explanation of A
A is true, R is false
A is false, R is true

⇒

Assertion (A): A half wavelength line can be used as a 1 : 1 transformer.

Reason (R): The input impedance of a half wavelength line is equal to load impedance.

Both A and R are correct and R is correct explanation of A
Both A and R are correct but R is not correct explanation of A
A is correct but R is wrong
A is wrong but R is correct

⇒ The phase angle characteristic in the given figure is
all pass function
transport lag
minimum phase function
none of the above

⇒ If F(t) = δ(t - a), F(s)=
0
1
e^-as
e^as

⇒ Which one of the following devices is not used as the controller in a stabilizer?
DIAC
TRIAC
SCR
Power transistor

⇒ The number of flip-flops required to build a mod-19 counter is
4
5
6
7