Question is ⇒ In case of a direct vernier scale., Options are ⇒ (A) graduations increase in opposite direction in which graduations of the main scale increase, (B) smallest division is longer than smallest division of the main scale, (C) graduations increase in the same direction in which graduations of the main scale increase, (D) none of these., (E) , Leave your comments or Download question paper.

Question is ⇒ In case of a direct vernier scale., Options are ⇒ (A) graduations increase in opposite direction in which graduations of the main scale increase, (B) smallest division is longer than smallest division of the main scale, (C) graduations increase in the same direction in which graduations of the main scale increase, (D) none of these., (E) , Leave your comments or Download question paper. Previous question Next question


Q1.	In case of a direct vernier scale.
A.	graduations increase in opposite direction in which graduations of the main scale increase [Wrong Answer]
B.	smallest division is longer than smallest division of the main scale [Wrong Answer]
C.	graduations increase in the same direction in which graduations of the main scale increase [Correct Answer]
D.	none of these. [Wrong Answer]
View Answer 23 -3 Explanation:- Answer : C Discuss it below : !! OOPS Login [Click here] is required to post your answer/result Help other students, write article, leave your comments

Previous question Next question

Also Read Similar Questions Below :

⇒ The boundary of water of a still lake, represents.
level surface
horizontal surface
contour line
a concave surface.

⇒ In case of reduction of levels by the height of instrument method,
âˆ‘ B.S. - âˆ‘ F.S. = difference in R.L.S of the first station and last station
âˆ‘ (R.L. + I + F.S.) - first R.L = âˆ‘ (H.I. + No. of R.L.s.)
both (a) and (b) above
neither (a) nor (b).

⇒ The branch of surveying in which both horizontal and vertical positions of a point, are determined by making instrumental observations, is known.
tacheometry
tachemetry
telemetry
all the above.

⇒ The bearing of lines OA and OB are 16° 10' and 332° 18', the value of the included angleBOA is.
316Â° 10'
158Â° 28'
348Â° 08'
43Â° 52'

⇒ The area of any irregular figure of the plotted map is measured with.
pentagraph
sextant
clinometer
optical square

⇒ A uniform slope was measured by the method of stepping. If the difference in level between two points is 1.8 m and the slope distance between them is 15 m, the error is approximately equal to.
cumulative, + 0.11 m
compensating, Â± 0.11 m
cumulative, - 0.11 m
none of these

⇒ The rise and fall method
is less.accurate than height of instrument method
is not suitable for levelling with tilting levels
provides a check on the reduction of intermediate point levels
quicker and less tedious for large number of intermediate sights

⇒ Back bearing of a line is equal to.
Fore bearing Â± 90Â°
Fore bearing Â± 180Â°
Fore bearing Â± 360Â°
Fore bearing Â± 270Â°

⇒ An offset rod is provided at its top with
Hook
Flag
Distance measuring arrangement
None of these

⇒ As per Indian standard, the length of one link in 30 metre chain should be
30 cm
20 cm
40 cm
10 cm

⇒ In case of geographical maps, the scale is usually
1 cm = 10 cm to 10 cm
1 cm = 50 m to 100m
1 cm = 5 km to 160 km
1 cm = more than 200 km

⇒ The chaining on sloping ground is.
easier along the falling gradient
easier along the up gradient
equally convenient along falling as well as up gradient
all the above.

⇒ The conventional sign shown in below figure represents a

bridge carrying railway below road
bridge carrying road below railway
bridge carrying road and railway at the same level
a level crossing.

⇒ The needle of magnetic compass is generally supported on a
Ball bearing
Bush bearing
Needle bearing
Jewel bearing

⇒ The reduced bearing of a line is N 87° W. Its whole circle bearing is.
87Â°
273Â°
93Â°
3Â°

⇒ The properties of autogenous curve for automobiles are given by.
true spiral
cubic parabola
Bernoulli's Lemniscate
clothoid spiral.

⇒ The staff intercept will be.
greater farther off the staff is held
smaller, farther off the staff is held
smaller, nearer the staff is held
same, wherever the staff is held.

⇒ The magnetic meridian at any point, is the direction indicated by a freely suspended
magnetic needle
and properly balanced magnetic needle
properly balanced and uninfluenced by local attractive force
magnetic needle over an iron pivot.

⇒ The rise and fall method of levelling provides a complete check on
backsight
intermediate sight
foresight
all of the above

⇒ For which of the following permanent adjustments of theodolite, the spire test is used ?
adjustment of plate levels
adjustment of line of sight
adjustment of horizontal axis
adjustment of altitude bubble and vertical index frame

⇒ The temporary adjustment of a prismatic compass is
Centring
Adjustment of levels
Adjustment of needle
Adjustment of vane

⇒ If the length of a chain is found to be short on testing, it can be adjusted by
straightening the links
removing one or more small circular rings
closing the joints of the rings if opened out
all of the above

⇒ Two contour lines, having the same elevation.
cannot cross each other
can cross each other
cannot unite together
can unite together.

⇒ Theodolite is an instrument used for
tightening the capstan-headed nuts of level tube
measurement of horizontal angles only
measurement of vertical angles only
measurement of both horizontal and vertical angles

⇒ The real image of an object formed by the objective, must lie.
in the plane of cross hairs
at the centre of the telescope
at the optical centre of the eye-piece
anywhere inside the telescope.

⇒ Magnetic declination at any place.
remains constant
does not remain constant
fluctuates
changes abruptly.

⇒ The allowable length of an offset depends upon the
degree of accuracy required
method of setting out the perpendiculars and nature of ground
scale of plotting
all of the above

⇒ The longitudinal section of the surface of bubble tube is.
straight
circular
parabolic
elliptic.

⇒ The correction to be applied to each 30 metre chain length along θ° slope, is.
30 (sec Î¸ - 1) m
30 (sin Î¸ - 1) m
30 (cos Î¸ - 1) m
30 (tan Î¸ - 1) m

⇒ Pick up the correct statement from the following :
The horizontal angle between magnetic meridian and true meridian at a place is called magnetic declination or variance of the compass
the imaginary lines which pass through points at which the magnetic declinations are equal at a given time are called isogonic lines
the isogonic lines through places at which the declination is zero are termed agonic lines
all the above.