Question is ⇒ In an induction motor, closed slots are preferred for, Options are ⇒ (A) small size raachines, (B) medium size raachines, (C) large size machines, (D) none of the above, (E) , Leave your comments or Download question paper.

Question is ⇒ In an induction motor, closed slots are preferred for, Options are ⇒ (A) small size raachines, (B) medium size raachines, (C) large size machines, (D) none of the above, (E) , Leave your comments or Download question paper. Previous question Next question


Q1.	In an induction motor, closed slots are preferred for
A.	small size raachines [Correct Answer]
B.	medium size raachines [Wrong Answer]
C.	large size machines [Wrong Answer]
D.	none of the above [Wrong Answer]
View Answer 4 -3 Explanation:- Answer : A Discuss it below : !! OOPS Login [Click here] is required to post your answer/result Help other students, write article, leave your comments

Previous question Next question

Also Read Similar Questions Below :

⇒ The action of electromagnetic machines can be related to which of the following basic principles ?
Induction
Interaction
Alignment
All of the above

⇒ The voltage control in electric supply networks in required on account of which of the following reasons ?
Adjustment ofvoltage at consumers premises within statutory limits
Control of active and reactive power
Adjustment of short period daily and seasonal voltage variations in accordance with variations of load
All of the above

⇒ Machines cooled by direct cooling method may be called
supercharged
inner cooled
conductor cooled
any of the above

⇒ A current density of ____ is used for large power transformers with forced circulation of oil or with water cooling coils
1.5 to 2.5 A/mm²
3.5 to 4.5 A/mm²
4.0 to 5.0 A/mm²
5.4 to 6.2 A/mm²

⇒ The air gap of an induction motor is made as ____ as possible.
small
large
either of the above
none of the above

⇒ Pitch of commutator segment should not be less than
1 mm
2 mm
3 mm
4 mm

⇒ The heated parts of an electrical machine dissipate heat into their surroundings by which of the following modes of heat dissipation ?
Conduction
Convection
Radiation
All of the above

⇒ Which of the following methods may be adopted to reduce the effects of armature reaction ?
Increase in length of air gap at pole tips
In.creasing reluctance of pole tips
Compensating windings
Interpoles

⇒ The forced oil and air circulation method is usual one for transformers of capacities
upto 5 MVA
upto 10 MVA
upto 20 MVA
30 MVA upwards

⇒ In a D.C. machine the current per brush arm should not be more than
100 A
200 A
300 A
400 A

⇒ The value of exciting or magnetizing current depends upon which of the following factors ?
Total m.m.f. required
The number of turns in the exciting winding
The way in which the winding is distributed
All of the above

⇒ The slot leakage can be calculated by making which of the following assumptions ?
The current in the slot conductors is uniformly distributed over their cross-section
The leakage path is straight across the slot and around the iron at the bottom
The permanence of air paths is only considered. The reluctance of iron paths is assumed as zero
All of the above

⇒ ____ has a low relative permeability and is used principally in field frames when cost is of primary importance and extra weight is not objectionable.
Cast steel
Aluminium
Soft steel
Cast iron

⇒ Direct water cooling of rotor winding presents
no mechanical difficulties
lesser mechanical difficulties
greater mechanical difficulties
none of the above

⇒ The diameter ofcommutator generally lies
between 0.2 to 0.4 of armature diameter
between 0.4 to 0.6 of armature diameter
between 0.6 to 0.8 of armature diameter
none of the above

⇒ Multi-layer helical windings are commonly used in the transformers as high voltage windings
upto 20 kV
upto 50 kV
upto 80 kV
for 110 kV and above

⇒ For 275 kV transformers, using cold rolled grain oriented steel, which of the following values of flux density may I used ?
1.0 Wb/m²
1.1 Wb/m²
1.3 Wb/m²
1.6 Wb/m²

⇒ Transformer oil should have
high flash point
high viscosity
high sludging tendencies
none of the above

⇒ The number of stator slots should ____ be equal to the number of rotor slots
always
never
sometimes
none of the above

⇒ By which of the following methods the temperature rise of windings and other parts may be determines ?
Thermonieter method
Resistance method
Embedded temperature detector method
Any of the above

⇒ If an insulating material is operated beyond the maximum allowable temperature, its life is
drastically increased
drastically reduced
unaffected
none of the above

⇒ The electric motor provided on refrigerators is usually
totally enclosed type
screen protected type
open type
protected type

⇒ The transformer ID oise is mainly due to
magnetic flux
sinusoidal current
cooling coil
all of the above

⇒ Which of the following brushes can be used for high values of current density ?
Metal graphite brushes
Hard carbon brushes
Electro-graphitic brushes
Natural graphite brushes

⇒ Which of the following is the commonly used type of electroinagnets ?
Flat-faced armature type
Horse shoe type
Flat-faced plunger type
All of the above

⇒ In an induction motor, closed slots are preferred for
small size raachines
medium size raachines
large size machines
none of the above

⇒ The increase in heat dissipation by air blasts is due to increase in ____
conduction
convection
radiation
any of the above

⇒ Multiple inlet system of air cooling of turbo-alternators can be used for rnachines of rating upto
10 MW
30 MW
60 MW
150 MW

⇒ In a D.C. generator the number ofcommutator segments is
equal to the number of coils
less than the number of coils
greater than the nunnber of coils
none of the above

⇒ Hydrogen has a heat transfer co-efficient ____ times that of air
1.5
2.5
3.5
4.5