Question is ⇒ In a Vidicon camera tube, Options are ⇒ (A) grid G1 accelerates electrons, (B) grid G2 accelerates electrons and grid G3, slows down electrons, (C) grid G3 accelerates electrons and grid G2 slows down electrons, (D) both grids G2 and G3 accelerate electrons, (E) , Leave your comments or Download question paper.

Question is ⇒ In a Vidicon camera tube, Options are ⇒ (A) grid G1 accelerates electrons, (B) grid G2 accelerates electrons and grid G3, slows down electrons, (C) grid G3 accelerates electrons and grid G2 slows down electrons, (D) both grids G2 and G3 accelerate electrons, (E) , Leave your comments or Download question paper. Previous question Next question


Q1.	In a Vidicon camera tube
A.	grid G₁ accelerates electrons [Wrong Answer]
B.	grid G₂ accelerates electrons and grid G₃, slows down electrons [Correct Answer]
C.	grid G₃ accelerates electrons and grid G₂ slows down electrons [Wrong Answer]
D.	both grids G₂ and G₃ accelerate electrons [Wrong Answer]
View Answer 1 -1 Explanation:- Answer : B Discuss it below : !! OOPS Login [Click here] is required to post your answer/result Help other students, write article, leave your comments

Previous question Next question

Also Read Similar Questions Below :

⇒ With respect to transmission parameters, which one of the following is correct?
A and B are dimensionless
B and C are dimensionless
A and D are dimensionless
B and D are dimensionless

⇒ The correct form of expression B³ -2 A C in FORTRAN 77 is
B * * 3 - 2 * A * C
B * 3 - 2 * A AC
B * * 3 - 2 ** A * C
B *** 3 - 2 * A * C

⇒ In a mod-12 counter the input clock frequency is 10 kHz. The output frequency is
0.833 kHz
1.0 kHz
0.91 kHz
0.77 kHz

⇒ Which of the following semiconductor has the highest melting point?
Germanium
Silicon
Gallium arsenide
Lead sulphide

⇒ The current i(t) through a 10 Ω resistor in series with an inductance is given by i(t) = 3 + 4 sin (100t + 45°) + 4 sin (300t + 60°) Amperes. The RMS value of the current and the power dissipated in the circuit are
41 A, 410 W respectively
35 A, 350 W respectively
5 A, 250 W respectively
11 A, 1210 W respectively

⇒ As frequency is increased, the skin effect
increases
decreases
remains the same
either (b) or (c)

⇒ Which of the following is used for generating time varying wave forms?
MOSFET
PIN diode
Tunnel diode
UJT

⇒ The method used to transfer data from I/O units to memory by suspending the memory-CPU data transfer for one memory cycle is called
I/O spooling
Cycle stealing
Line conditioning
Demand paging

⇒ Two port circuits are connected in parallel. To determine the response, it is more convenient to use
O.C. impedance parameters
S.C. admittance parameters
ABCD parameters
h parameters

⇒ For a P-N junction diode, the current in reverse bias may be
few amperes
between 0.5 A and 1 A
few milliamperes
few micro or nanoamperes

⇒ The value of current read by ideal ammeter A in figure is __________ amp
0
3
2.5
5

⇒ Electronic tubes used for transmitter differ from their counterparts in the receivers in respect that
they are large in size
they are capable of handling large powers
they generate large amount of heat when in operation
none of the above

⇒

Match the following:

	List I (Bit Pattern)		List II (Register pairs)
A.	00	1.	SP
B.	01	2.	B-C
C.	10	3.	D-E
D.	11	4.	H-L

A-1, B-2, C-3, D-4
A-2, B-3, C-4, D-1
A-2, B-3, C-1, D-4
A-4, B-3, C-2, D-1

⇒ In its lowest state, the electron is bound to the field of proton by an energy equal to
100.5 eV
51.2 eV
13.6 eV
0.2 eV

⇒

Assertion (A): Negative feedback reduces the gain of an amplifier

Reason (R): Negative feedback is very commonly used in amplifier circuits

Both A and R are correct and R is correct explanation for A
Both A and R are correct but R is not correct explanation for A
A is correct R is wrong
A is wrong R is correct

⇒ Shifting digits from left to right and vice versa is needed in
storing numbers
arithmetic operations
counting
storing and counting

⇒ If the time is counted from the instant when an ac wave is at its peak value, we get a
sine wave
cosine wave
distorted sine wave
none of the above

⇒ A copper specimen has resistivity equal to 1.8 x 10^-8 ohm-m at room temperature. At a temperature of 700 K, the resistivity is likely to be
1.6 x 10^-8 Ω-m
2 x 10^-8 Ω-m
3 x 10^-8 Ω-m
6 x 10^-8 Ω-m

⇒ It is possible to use a freewheeling diode in
single phase half wave controlled rectifier as well as in single phase full wave controlled rectifier (M - 2 connection)
single phase half wave controlled rectifier but not in single phase full wave controlled rectifier (M - 2 connection)
single phase full wave controlled rectifier (M - 2 connection) but not in single phase half wave controlled rectifier
all controlled rectifier circuits

⇒ The output wave of a cycloconverter consists of a number of segments derived from the input wave.
TRUE
FALSE

⇒ A broadside array consisting of 200 cm wavelength with 10 half-wave dipole spacing 10 cm. And if each array element feeding with 1 amp. current and operating at same frequency then find the radiated power
730 W
73 W
100 W
None

⇒ For the circuit of the given figure, the output equatio
Y = ABCD
Y = AB + CD
Y = A + BCD
Y = ABC + D

⇒ If a two port network is represented by an equivalent T network the admittance of series arm in term of ABCD parameter is equal to
C
1/C
(A - 1)/B
1/B

⇒ If e = 10 sin(10⁸ t + 3 sin 10⁴ t) then carrier frequency is
0.159 MHz
1.59 MHz
15.9 MHz
159 MHz

⇒ Which of the following power amplifiers has highest efficiency?
Class A
Class AB
Class B
Class C

⇒ In classical analogue, torque is analogous to
current
voltage
charge
voltage gradient

⇒ The race condition in NOR SR latch occurs when
S = R = 1
S = 0, R = 1
S = 0, R = 0
S = 1, R = 0

⇒ The present total cost per watt of power generation in geosynchronous orbit is nearly Rs.
20
50
100
5

⇒

Assertion (A): In SSB, carrier is suppressed by about 45 dB

Reason (R): SSB is standard form for radio communication

Both A and R are correct and R is correct explanation of A
Both A and R are correct but R is not correct explanation of A
A is correct but R is wrong
A is wrong but R is correct

⇒ The fabrication of microstrip line is done by
photo etching
printed circuit technique
oxidation
cladding