Question is ⇒ In a tap changing transformer, the tappings are provided on, Options are ⇒ (A) primary winding, (B) secondary winding, (C) high voltage winding, (D) any of the above, (E) , Leave your comments or Download question paper.

Question is ⇒ In a tap changing transformer, the tappings are provided on, Options are ⇒ (A) primary winding, (B) secondary winding, (C) high voltage winding, (D) any of the above, (E) , Leave your comments or Download question paper. Previous question Next question


Q1.	In a tap changing transformer, the tappings are provided on
A.	primary winding [Wrong Answer]
B.	secondary winding [Correct Answer]
C.	high voltage winding [Wrong Answer]
D.	any of the above [Wrong Answer]
View Answer 10 -104 Explanation:- Answer : B Discuss it below : S RAVI Said on 2019-05-13 00:05:28 ANSWER IS C OPTION ANKIT Said on 2017-09-09 20:29:53 C is all right Goudappa Said on 2017-03-12 07:35:42 Ans tap changing in high voltage side Thejasvi Said on 2017-01-25 03:32:51 c is right Vipul Said on 2016-10-30 00:38:04 c is right Vibhu Said on 2016-02-25 05:59:25 c !! OOPS Login [Click here] is required to post your answer/result Help other students, write article, leave your comments

Previous question Next question

Also Read Similar Questions Below :

⇒ In medium transmission lines the shunt capacitance is taken into account in
T-method
π-method
steinmetz method
all of the above

⇒ Steepness of the travelling waves is alternated by ____ of the line
capacitance
inductance
resistance
all of the above

⇒ Transmitted power remaining the same, if supply voltage of a D.C. 2-wire feeder is increased 100 percent, saving in copper is
25 percent
50 percent
75 percent
100 percent

⇒ Induction regulators are used for voltage control in
alternators
primary distribution
secondary distribution
none of the above

⇒ The operating voltage of supertension cables is upto
3.3 kV
6.6 kV
11 kV
33 kV

⇒ In overhead transmission lines the effect of capacitance can be neglected when the length of line is less than
80 km
110 km
150 km
210 km

⇒ In a D.C. 3-wire distribution system, balancer fields are cross-connected in order to
boost the generated voltage
balance loads on both sides of the neutral
make both machines run as unloaded motors
equalize voltages on the positive and negative outers

⇒ The skin effect of a conductor will reduce as the
resistivity of conductor material increases
permeability of conductor material increases
diameter increases
frequency increases

⇒ A tap changing transformer is used to
supply low voltage current for instruments
step up the voltage
step down the voltage
step up as well as step down the voltage

⇒ Electro-mechanical voltage regulators are generally used in
reactors
generators
transformers
all of the above

⇒ The material commonly used for insulation in high voltage cables is
lead
paper
rubber
none of the above

⇒ Which of the following distribution systems is the most economical ?
A.C. 1-phase system
A.C. 3-phase 3 wire system
A.C. 3-phase 4 wire system
Direct current system

⇒ Which of the following distribution systems is more reliable ?
Radial system
Tree system
Ring main system
All are equally reliable

⇒ The effect of wind pressure is more predominant on
supporting towers
neutral wires
transmission lines
insulators

⇒ The angular displacementbetween two interconnected stations is mainly due to
armature reactance of both alternators
reactance of the interconnector
synchronous reactance of both the alternators
all of the above

⇒ By which of the following methods the protection against direct lightning strokes and high voltage sweep waves is provided ?
Lightening arresters
Ground wire
Lightening arresters and ground wires
Earthing of neutral

⇒ In a tap changing transformer, the tappings are provided on
primary winding
secondary winding
high voltage winding
any of the above

⇒ Overhead system can be designed for operation upto
11 kV
33 kV
66 kV
400 kV

⇒ Which of the following bar schemes is the most expensive ?
Double bus-bar double breaker
Ring bus-bar scheme
Single bus-bar scheme
Main and transfer scheme

⇒ High voltage is primarily used, for long distance power transmission, to
reduce the time of transmission
reduce the transmission losses
make the system reliable
none of the above

⇒ The phenomenon of rise in voltage at the receiving end of the open-circuited or lightly loaded line is called the
Seeback effect
Ferranti effect
Raman effect
none of the above

⇒ For transmission of power over a distance of 200 km, the transmission voltage should be
132 kV
66 kV
33 kV
11 kV

⇒ Which of the following is a static exciter ?
Rectifier
Rotorol
Amplidyne
D.C. separately excited generator

⇒ Poles which carry transformers are usually
circular
I-type
A-type
H-type

⇒ High voltage transmission lines use
suspension insulators
pin insulators
both (a) and (b)
none of the above

⇒ Power loss due to corona is not directly proportional to
spacing between conductors
supply voltage frequency
phase-neutral voltage
all of the above

⇒ Floating neutral, in 3-phase supply, is undesirable because it causes
low voltage across the load
high voltage across the load
unequal line voltages across the load
none of the above

⇒ The effect of corona can be detected by
presence of zone detected by odour
hissing sound
faint luminous glow of bluish colour
all of the above

⇒ The following system is not generally used
1-phase 3 wire
1-phase 4 wire
3-phase 3 wire
3-phase 4 wire

⇒ In transmission and distribution system the permissible voltage variation is
± 1 percent
± 10 percent
± 20 percent
± 30 percent