Users Also Read

MCQ's Search Engine

Electrical Engineering

Mechanical Engineering

Civil Engineering

Automobile Engineering

Chemical Engineering

Computer Engineering

Electronics Engineering

Medical Science Engg

Q1. | In a superheterodyne receiver with an IF of 450 kHz is tuned to a signal at 1200 kHz. The image frequency is |

A. | 750 kHz [Wrong Answer] |

B. | 990 kHz [Wrong Answer] |

C. | 1650 kHz [Wrong Answer] |

D. | 2100 kHz [Correct Answer] |

View Answer
Explanation:-
Answer : DDiscuss it below :!! OOPS Login [Click here] is required to post your answer/resultHelp other students, write article, leave your comments |

**Also Read Similar Questions Below :**

⇒ F = ∑(0, 3, 4, 5, 7) =

[B ⊕ C] + AC

B'C' + BC + AC

AB + BC + CA

None

⇒ The decimal equivalent of the binary number 10110.0101011101 is

22.24082165

22.340821675

22.3408213125

22.3408203125

⇒ A 400 W carrier is modulated to a depth of 75 percent. The total power in modulated wave will be

38.5 W

400 W

512.5 W

615.5 W

⇒ If figure, power dissipated in 30Ω resistance will be maximum when value of

30 Ω

16 Ω

9 Ω

zero

⇒ The main advantage of CMOS circuit is

high gain

high output impedance

low power consumption

high gain and high output impedance

⇒ As compared to a

*p*-

*n*junction diode

a schottky diode has lower cut in voltage and lower reverse saturation current

a schottky diode has higher cut in voltage and higher reverse saturation current

a Schottky diode has lower cut in voltage and higher reverse saturation current

a schottky diode has higher cut in voltage and lower reverse saturation current

⇒ IC counters are

synchronous only

asynchronous only

both synchronous and asynchronous

none of the above

⇒ The given figure shows a constant current source driving a parallel RC circuit. It is equivalen

a lag network

a lead network

a lag-lead network

either (a) or (b)

⇒ A wire strain gauge has a gauge factor of 2, resistance of 125 Ω and length 1 m. If length of wire changes by .005 m, change in resistance will be

0.25 Ω

0.5 Ω

1.25 Ω

2.5 Ω

⇒ Find V

_{th}in the cir

100 V

10 V

0 V

5 V

⇒ In microwave system the function of mode filter is

to suppress modes with lower cut off frequencies

to suppress modes with higher cut off frequencies

to change mode of wave transmission

both (b) and (c)

⇒ When diodes are connected in series to increase voltage rating the peak inverse voltage per junction

should not exceed half the breakdown voltage

should not exceed the breakdown voltage

should not exceed one third the breakdown voltage

may be equal to or less than breakdown voltage

⇒ A resistance strain gauge has a resistance of about

100 Ω

25 Ω

10 Ω

1 Ω

⇒ If F(

*j*ω) is the Fourier transform of

*f*(

*t*), then

£

*f*(-

*t*) = F(

*j*ω)

£

*f*(-

*t*) = F* (

*j*ω)

£

*f*(-

*t*) = F(-

*j*ω)

£

*f*(-

*t*) = F* (

*- j*ω)

⇒ In a series operated thyristor configuration, each thyristor should support 100 V. However, the three thyristors only support voltage of 100 V, 90 V and 85 V respectively. Hence, the string efficiency in the case is :

0.9845

0.4584

0.9167

none of these

⇒ If

*f*be the signal frequency and

_{s}*f*be the intermediate frequency then image frequency is given by

_{i}*f*+

_{s}*f*

_{i}*f*±

_{s}*f*

_{i}*f*± 2

_{s}*f*

_{i}*f*+ 2

_{s}*f*

_{i}⇒ Which of the- following display consumes least amount of power?

LCD

LED

Fluorescent display

All display consume same power

⇒ Which of the following modes in circular waveguides are circularly symmetric?

TE

_{01}

TE

_{02}

both (a) and (b)

neither (a) nor (b)

⇒ In 8085 microprocessor, in order to enable RST 5.5, RST 6.5 and RST 7.5 interrupts, which of the following instruction are needed?

EI only

SIM only

EI and SIM both

None

⇒ In TV transmitter, visual exciter may consist of

- Video processing unit
- Visual modulator
- VSB filter
- Delay equaliser
- Frequency converter

1, 2 and 3

2, 3 and 4

1, 2, 3 and 4

1, 2, 3, 4 and 5

⇒ Varactor diode is forward biased when it is used.

TRUE

FALSE

⇒ A 10 MHz square wave clocks 5 bit ripple counter. The frequency of the 3rd FF output is

2 MHz

1.25 MHz

50 MHz

615 kHz

⇒ The input resistance of FET in the low frequency small signal operation is

infinitely high

around 1 kΩ

around 50 Ω

very small

⇒ For a transfer function H(

*s*) = P(

*s*)/Q(

*s*), where P(

*s*) and Q(

*s*) are polynomials in

*s*

the degrees of P(

*s*) is always greater than degree of Q(

*s*)

the degree of P(

*s*) and Q(

*s*) are equal

the degree of P(

*s*) is independent of degree of Q(

*s*)

the maximum difference in degrees of P(

*s*) and Q(

*s*) is 1

⇒ The addition of a pole to the open loop transfer function pulls the root locus

to the right

to the left and making the system more stable

towards right or left depending on the position of new pole

none of the above

⇒ In figure, the current through 2 Ω resistanc

zero

-2A

2A

1A

⇒ In a 3 phase fully controlled converter the firing frequency is

3 times the line frequency

6 times the line frequency

9 times the line frequency

12 times the line frequency

⇒ To find current in a resistance connected in a network, Thevenin's theorem is used V

_{TH}= 20 V and R

_{TH}= 5 Ω. The current through the resistance

is 4 A

is 4 A or less

is less than 4 A

may be 4 A or less or more than 4 A

⇒ Tellegen's theorem is applicable to

circuits with passive elements only

circuits with linear elements only

circuits with time invariant elements only

circuits with active or passive, linear or nonlinear and time invariant or time varying elements

⇒ In figure I

_{D}= 4 mA. Then V

_{S20 V4.4 V0.4 V0.44 V}