Question is ⇒ In a ripple counter,, Options are ⇒ (A) whenever a flip flop sets to 1, the next higher FF toggles, (B) whenever a flip flop sets to 0, the next higher FF remains unchanged, (C) whenever a flip flop sets to 1, the next higher FF faces race condition, (D) whenever a flip flop sets to 0, the next higher FF faces race condition, (E) , Leave your comments or Download question paper.

Question is ⇒ In a ripple counter,, Options are ⇒ (A) whenever a flip flop sets to 1, the next higher FF toggles, (B) whenever a flip flop sets to 0, the next higher FF remains unchanged, (C) whenever a flip flop sets to 1, the next higher FF faces race condition, (D) whenever a flip flop sets to 0, the next higher FF faces race condition, (E) , Leave your comments or Download question paper. Previous question Next question


Q1.	In a ripple counter,
A.	whenever a flip flop sets to 1, the next higher FF toggles [Correct Answer]
B.	whenever a flip flop sets to 0, the next higher FF remains unchanged [Wrong Answer]
C.	whenever a flip flop sets to 1, the next higher FF faces race condition [Wrong Answer]
D.	whenever a flip flop sets to 0, the next higher FF faces race condition [Wrong Answer]
View Answer 1 -2 Explanation:- Answer : A Discuss it below : !! OOPS Login [Click here] is required to post your answer/result Help other students, write article, leave your comments

Previous question Next question

Also Read Similar Questions Below :

⇒ Top loading in an antenna increases
effective height
beam width
input capacitance
bandwidth

⇒ Leak type bias is used in a plate-modulated class C amplifier to
prevent tuned circuit damping
prevent over modulation
increase the bandwidth
prevent excessive grid current

⇒ A number of impulses spaced fron one another form an impulse train.
TRUE
FALSE

⇒ In a 3 input NOR gate, the number of states in which output is 1 equals
1
2
3
4

⇒ Most of the digital computers do not have floating-point hardware because
floating point hardware is costly
it is slower than software
it is not possible to perform floating point addition by hardware
of not specific reason

⇒ Which of the following is invalid in Basic?
A ** B - C
5.2 ** 4.3
5.2 ** (- 4.3)
(- 5.2) ** (4.3)

⇒ Unlimited number of ICs 7490, 78492 and 7493 are available. Which of these could be used to build the dividse-by-60 circuit of fi
7490
7492
combination of 7490 and 7492
combination of 7492 and 7493

⇒ Two 2 port circuits are connected cascaded. To determine the response, it is more convenient to use
O.C. impedance parameters
S.C. admittance parameters
ABCD parameters
h parameters

⇒ The current i(t), though a 10 Ω resistor in series with an inductance, is given by i(t) = 3 + 4 sin (10t + 45°) + 4 sin (300t + 60°) Amperes. The RMS value of the current and the power dissipated in the circuit are
41 A, 410 W, respectively
35 A, 350 W, respectively
5 A, 250 W, respectively
11 A, 1210 W, respectively

⇒ Mouse is a very suitable input device for computers.
TRUE
FALSE

⇒ The types of carriers in a semiconductor are
1
2
3
4

⇒ Consider the instructions

MOV M, B
OUT 4
LDA X

Which of the above uses IO/W cycle?
1 only
1 and 2 only
2 only
3 only

⇒ What is an advantage of an electronic voltmeter over a non-electronic voltmeter?
Low power consumption
Low input impedance
The ability to measure wide ranges of voltages and resistance
Large portability

⇒ In figure, power in 6 Ω resistor is zero then
202∠45°
20 ∠30°
20 ∠45°
202∠30°

⇒ The electric flux and field intensity inside a conducting sphere is
minimum
maximum
uniform
zero

⇒ A single phase full converter gives maximum and minimum output voltage at firing angles of
0 and 180° respectively
180° and 0° respectively
0 and 90° respectively
90° and 0° respectively

⇒ For an RC admittance function
all poles and zeros are simple
all poles and zeros are simple and lie on negative real axis
all poles and zeros lie on imaginary axis
all poles and zeros lie on positive real axis

⇒ The main advantage of TDM over FDM is
TDM requires more bandwidth than FDM
less complicated in hardware than FDM
better SNR
required filter

⇒ Consider the following statements

Usable bandwidth of ridge wave guide is more than that of rectangular waveguide.
For a given value of TM₁₀ cutoff frequency the cross section of ridge wave guide is lesser that that of rect angular waveguide.
Ridge wave guide has higher conductor losser than a rectangular waveguide.
Ridge guide has higher conductor losser than a rectangular waveguide.

Which of the above statements are correct?
1 and 2 only
1, 2 and 3 only
2 and 3 only
All

⇒ Frequency band used for radar is generally
VLF
VHF
UHF
EHF

⇒ In the above case the modulation index will be
9.6
28.8
57.6
100

⇒ The phase angle curve of G(jω) H(jω) is drawn by adding the phase angles of individual factors.
TRUE
FALSE

⇒ Which of the following is not a legal subscript?
J + 2
JA - 4
-3
3^* IA - 2

⇒ The natural frequency S_n of the given circui
-1
1
42737
-2

⇒

Match the following:

	List I (Memories)		List II (Characteristic)
A.	Static PLA	1.	erasable, programmable
B.	CCD	2.	ultra high speed
C.	ECL	3.	stores large volume of data
D.	GAL	4.	Does not need refreshing
		5.	Non-volatile

A-4, B-3, C-2, D-1
A-4, B-2, C-3, D-1
A-5, B-1, C-2, D-3
A-3, B-5, C-2, D-1

⇒ The number of leads in an SCR are :
2
3
4
5

⇒ An engineer designs an amplifier to have a voltage gain of 60, but when constructed it only had a gain of 50. How much feedback should be used to provide the desired level?
0.0003
0.0033
0.013
0.033

⇒ The colour code on a carbon resistor is green-blue-yellow. The tolerance is
± 5%
± 10%
± 20%
± 30%

⇒

Assertion (A): Ferrites are very useful at very high frequencies.

Reason (R): Ferrites have high permeability and high resistivity.

Both A and R are true and R is correct explanation of A
Both A and R are true but R is not correct explanation of A
A is true but R is false
A is false but R is true

⇒ A semi converter operates in two quadrants.
TRUE
FALSE