Question is ⇒ In a radio receiver, if the intermediate frequency is too high, Options are ⇒ (A) Selectivity will be poor, (B) Tracking difficulties will be least, (C) Adjacent channel rejection will improve, (D) All of the above will occur, (E) , Leave your comments or Download question paper.

Question is ⇒ In a radio receiver, if the intermediate frequency is too high, Options are ⇒ (A) Selectivity will be poor, (B) Tracking difficulties will be least, (C) Adjacent channel rejection will improve, (D) All of the above will occur, (E) , Leave your comments or Download question paper. Previous question Next question


Q1.	In a radio receiver, if the intermediate frequency is too high
A.	Selectivity will be poor [Correct Answer]
B.	Tracking difficulties will be least [Wrong Answer]
C.	Adjacent channel rejection will improve [Wrong Answer]
D.	All of the above will occur [Wrong Answer]
View Answer 2 -2 Explanation:- Answer : A Discuss it below : !! OOPS Login [Click here] is required to post your answer/result Help other students, write article, leave your comments

Previous question Next question

Also Read Similar Questions Below :

⇒ What is the major cause of creeping in an energy-meter?
Over compensation for friction
Mechanical vibrations
Excessive voltage across the potential coil
Stray magnetic fields

⇒ The circuit in figure, the switched on at t = 0. After a long time the current through 5 Ω resistanc
0.0416666666666667
0.166666666666667
0.416666666666667
0

⇒ Which of the following statements is/are true for a good conductor of electricity?

Its conductivity decreases with increasing temperature.
Number of free electrons is around 10²⁸ m^-3.
Its conductivity decreases with addition of impurities.
It is a good conductor of heat also.

1, 2, 3 and 4
1 only
2 and 3 only
3 and 4 only

⇒

Match the following:

	List I (Transmission system)		List II (Mode)
A.	Rectangular waveguide	1.	TE/TM
B.	Circular waveguide	2.	TEM
C.	Coaxial line	3.	Quasi TEM
D.	Microstrip line

A-1, B-1, C-2, D-3
A-1, B-2, C-2, D-3
A-2, B-2, C-3, D-3
A-3, B-1, C-2, D-2

⇒ 23.6₁₀ = __________ ₂
11111.1001
10111.1001
111.101
10111.1

⇒ Laplacian of a scalar function v is
gradient of v
divergence of v
gradient of the gradient of v
divergence of the gradient of v

⇒ The pole zero plot of the given figure is
non-minimum phase function
minimum phase function
all pass function
either (b) or (c)

⇒ What will be conversion time of a successive approximation A/D converter which uses 2 MHz clock and 5 bit binary ladder containing 8 V reference.?
2.5 μ sec
25 μ sec
3 μ sec
4 μ sec

⇒ As compared to bipolar junction transistor, a FET
is less noisy
has better thermal stability
has higher input resistance
all of the above

⇒ Industrial heating furnaces such as arc and induction furnaces operate on __________ power factor
low leading
low lagging
high leading
very low lagging

⇒ A digital voltmeter has a 4 1/2 digit display. The 1 V range can measure voltage up to
0.9999 V
1.9999 V
0.199 V
9.999 V

⇒

Assertion (A): In 8085, P flag is for parity checking.

Reason (R): If the result of ALU has even parity, P flag is set and if the result has odd parity, P flag is reset.

Both A and R are correct and R is correct explanation of A
Both A and R are correct but R is not correct explanation of A
A is correct R is wrong
A is wrong R is correct

⇒ TTL uses
multi-emitter transistors
multi-collector transistors
multi-base transistors
multi-emitter or multi-collector transistors

⇒ In a C expression using assignment operators, relational operators and arithmetic operators, the hierarchy of operations (in the absence of parenthesis) is
assignment, relational, arithmetic
relational, assignment, arithmetic
arithmetic, assignment, relational
arithmetic, relational, assignment

⇒ For a given voltage, four heating coils will produce maximum heat when connected
all in parallel
all in series
with two parallel pairs in series
one pair in parallel with the other two in series

⇒ In a radar system the solution to blind speed problem is to
use MTI
use monopoles
vary PRF
change Doppler frequency

⇒ The function A e^st where s = s + jω represents
A phasor whose magnitude changes with time
A phasor whose frequency is ω
A phasor rotating in counterclockwise direction at angular frequency ω and whose magnitude increases with t
A phasor rotating in clockwise direction at angular frequency ω and whose magnitude increases with t

⇒ De Sauty bridge is very widely used due to
simplicity
perfect balance for imperfect capacitor
perfect balance for air capacitors
maximum sensitivity

⇒ For a circular wave guide
cutoff frequency for TE₁₀ and TE₀₁ modes are same
cutoff frequency for TE₁₀ and TE₀₁ modes are different
cutoff frequency for TE₁₀ mode = twice the cutoff frequency for TE₂₀ mode
cutoff frequency for TE₁₀ mode = haf the cutoff frequency for TE₂₀ mode

⇒ Which of the following oscillators is suitable for frequencies in the range of mega hertz?
RC phase shift
Wien bridge
Hartley
Both (a) and (c)

⇒ Which of the following statements is incorrect?
Ideal voltage source is one whose internal resistance is zero
Ideal voltage source is one whose internal conductance is zero
Ideal voltage source is one whose generated voltage is equal to the available terminal voltage
Ideal current source is one whose internal conductance is zero

⇒ The combination of registers in 8085 is B-C, D-E, H-L only.
TRUE
FALSE

⇒ The frequencies in ultra high frequency range are propagated by means of __________ waves
surface
ground
sky
space

⇒ In electronic voltmeters the measuring device is a
moving coil instrument
moving iron instrument
dynamometer instrument
none of the above

⇒ A reactor is used in a dual converter operating in non-circulating current mode.
TRUE
FALSE

⇒ Figure is a 24 V_r stabilized power supply. The zener is 24 V, 600 mW. The minimum zener current is 10 mA. Proper values R and maximum load current
320 Ω, 10 mA
400 Ω, 15 mA
400 Ω, 10 mA
320 Ω, 15 mA

⇒ The first row of the window is called ' Title bar '.
TRUE
FALSE

⇒

Assertion (A): In microprocessor 8085 DMA allows direct access to memory to speed up data transfer.

Reason (R): HOLD and HLDA signals are used for DMA operations.

Both A and R are correct and R is correct explanation of A
Both A and R are correct but R is not correct explanation of A
A is correct R is wrong
A is wrong R is correct

⇒ A 6 bit dual slope A/D converter uses a reference of -6v and a 1 MHz clock. It uses a fixed count of 40 (101000). Then, what will be input, if the output register shows 100111 at the end of conversion.
5.85 V
6 V
5 V
10 V

⇒ Which of the following is open loop system?
Wind screen wiper
Aqualing
Respiratory system of animal
System for controlling antirocket missiles