Question is ⇒ In a power transformer iron losses remain practically constant from no load to full load. This is because, Options are ⇒ (A) core flux remains constant., (B) leakage flux remains constant., (C) both (a) and (b)., (D) neither (a) nor (b)., (E) , Leave your comments or Download question paper.

Question is ⇒ In a power transformer iron losses remain practically constant from no load to full load. This is because, Options are ⇒ (A) core flux remains constant., (B) leakage flux remains constant., (C) both (a) and (b)., (D) neither (a) nor (b)., (E) , Leave your comments or Download question paper. Previous question Next question


Q1.	In a power transformer iron losses remain practically constant from no load to full load. This is because
A.	core flux remains constant. [Correct Answer]
B.	leakage flux remains constant. [Wrong Answer]
C.	both (a) and (b). [Wrong Answer]
D.	neither (a) nor (b). [Wrong Answer]
View Answer 1 -1 Explanation:- Answer : A Discuss it below : !! OOPS Login [Click here] is required to post your answer/result Help other students, write article, leave your comments

Previous question Next question

Also Read Similar Questions Below :

⇒ Which of the following statements about synchronous-induction motors is incorrect?
It is basically a wound rotor induction motor wïth fewer and larger slots on rotor.
It has a very small air gap as expected in a plain induction motor.
It is connected to 3-phase ac supply on stator side and to dc on rotor side.
It starts as an induction motor and runs as a synchronous motor.

⇒ An induction motor having 8 poles runs at 727.5 rpm. If the supply frequency is 50 Hz, the emf in the rotor will have a frequency of
1.5 Hz
48.5 Hz
5.15 Hz
75 Hz

⇒ If one of the 3-phases of supply to an induction motor fails. may be due to any reason. when the motor is running normally. the motor will
continue running at the same speed if it was running on light load.
continue running but will draw more current if it was operating at rated load.
stop and carry heavy current causing permanent damage to the windings if it was operating overloaded.
all of the above.

⇒ The electrical efficiency of a dc machine is given as the ratio of
VI_L and E_gI_a in case of generator.
E_bI_a and in case of motor.
output/input
output/output + total loss

⇒ ____coefficient is numerically equal to the difference of potential per °C.
Peltier
Thomson
Joule's
None of these

⇒ A threes-phase synchronous motor connected to ac mains is running at full load and unity power factor. If its shaft load is reduced by half, with field current held constant, its new power factor will be
unity.
leading.
lagging.
dependent on machine parameters.

⇒ Slip-changing method of speed control can be used in case of
slip-ring induction motors only.
squirrel cage induction motors only.
squirrel cage as well as slip-ring induction motors.
none of the above.

⇒ Tappings of a transformer are provided
at the phase end of lv side.
at the phase end of liv side.
at the neutral end f liv side.
at the middle of by side

⇒ A 3-phase synchronous motor hunts due to
fluctuating load.
fluctuating supply voltage.
excessive field current.
faulty connections.

⇒ A synchronous motor operating at rated voltage draws 1.0 pu current at 1.0 power factor. The machine parameters are synchronous reactance 1.0 pu; armature resistance negligible. Apart from supplying this rated power, if the motor has to supply an additional reactive power of 0.8 pu, then the field current has to he increased by
0.42
0.46
0.52
0.69

⇒ Screw projecting into the waveguide is
Capacitive discontinuity.
Inductive discontinuity.
May be capacitive or inductive depending upon the position inside the guide
None of the above.

⇒ In a drum type dc armature winding th back pitch and front pitch in terms of the coil-sides roust be
even and odd respectively.
odd and even respectively.
both even.
both odd.

⇒ In order to reduce the hysteresis loss
core may be laminated.
silicon steel may be used as the core material.
core may be constructed with any permanent magnet material such as Amico.
core may be impregnated with varnish.

⇒ In dynamic braking of 3-phase induction motors
the supply terminals of any two stator phases are interchanged.
any two stator terminals are earthed.
the stator terminals are switched over to ade source from the ac supply
a dc voltage is injected in the rotor circuit

⇒ 1f an additional resistance is connected in series with a dc series motor operating at rated speed, the speed of the motor will
reduce.
reduce.
remain unaltered.
oscillate around the normal speed.

⇒ The number of poles on a pony motor employed for starting of a 3- phase synchronous motor should be ____ that on the synchronous motor.
equal to
more than
lesser than
none of these

⇒ A round rotor synchronous generator has a leakage reactance of 10%, armature reaction reactance of 90% and negligible armature resistance. With the machine initially running at rated speed and terminal voltage of 1.0 pu, a 3-phase short-circuit is applied. The sustained armature current will be
1.25 pu
1.11 pu
1.0 pu
0.9 pu

⇒ Which one of the following types of motors is most suitable for a computer printer drive?
Reluctance motor
Hysteresis motor
Shaded pole motor
Stepper motor

⇒ Stability of a synchronous motor ____ with the increase in excitation.
increases
decreases
remains unaffected

⇒ If a single phase motor fails to start but gives humming noise, this may be due to
low voltage
high voltage
shorted stator winding
blown fuses

⇒ The low voltage winding of a 400/230 V single phase 50 Hz transformer is to be connected to a 25 Hz supply. In order to keep the magnetization current at the same level in both the cases the voltage at 25 Hz should be:
230V
460V
115V
65V

⇒ Which of the following tests can be conducted on other than shunt machines?
Swinburne's test.
Retardation test
Field's test.
Back-to-back test.

⇒ If the speed of a dc motor increases with load torque, then it is a
series motor.
permanent magnet.
differentially compounded motor.
cumulatively compounded motor.

⇒ If the load on an induction motor is increased from n load to full load, its slip and the power factor will, respectively:
decrease, decrease.
decrease, increase.
increase, decrease.
increase, increase

⇒ The all-day efficiency of a transformer depends primarily on
its copper loss.
the amount of load.
the duration of load.
both (b) and (c).

⇒ A motor used for punching machine is usually subjected to
full load continuously
part of full load continuously
no load.
intermittent load.

⇒ A coil having a resistance of 5 ω and inductance of 0.1 H is connected in series with a condenser of capacitance 50 pF. A constant alternating voltage of 200 V is applied to the circuit. The voltage across the coil at resonance is
200 volts
1,788 volts
1,800 volts
2,000 volts

⇒ Which one of the following statements is not true for anac servomotor?
Has low inertia rotor
Is a single phase motor
Has slip torque characteristic as straight line with negative slope.
Reference voltage frequency is high compared to signal frequency

⇒ When does a synchronous motor operate with leading power factor current?
While it is underexcited
While it is critically excited
While it is overexcited
While it is heavily loaded

⇒ Which of the following dc generators has rising V-I characteristics?
Series
Shunt
Compound
None.