Question is ⇒ In a piezoelectric crystal, application of a mechanical stress would produce, Options are ⇒ (A) plastic deformation of the crystal, (B) magnetic Dipoles in the crystal, (C) electric polarization in the crystal, (D) shift in the Fermi level, (E) , Leave your comments or Download question paper.

Question is ⇒ In a piezoelectric crystal, application of a mechanical stress would produce, Options are ⇒ (A) plastic deformation of the crystal, (B) magnetic Dipoles in the crystal, (C) electric polarization in the crystal, (D) shift in the Fermi level, (E) , Leave your comments or Download question paper. Previous question Next question


Q1.	In a piezoelectric crystal, application of a mechanical stress would produce
A.	plastic deformation of the crystal [Wrong Answer]
B.	magnetic Dipoles in the crystal [Wrong Answer]
C.	electric polarization in the crystal [Correct Answer]
D.	shift in the Fermi level [Wrong Answer]
View Answer 1 -1 Explanation:- Answer : C Discuss it below : !! OOPS Login [Click here] is required to post your answer/result Help other students, write article, leave your comments

Previous question Next question

Also Read Similar Questions Below :

⇒ A full adder is to be implemented using half adders and OR gates. A 4 bit parallel adder without any initial carry requires
8 half adders and 4 OR gates
8 half adders and 3 OR gates
7 half adders and 3 OR gates
7 half adders and 4 OR gates

⇒ For a directional coupler the power is in the ratio of
40 dB
30 dB
20 dB
10 dB

⇒

Match the following:

	List I (Transmission system)		List II (Mode)
A.	Rectangular waveguide	1.	TE/TM
B.	Circular waveguide	2.	TEM
C.	Coaxial line	3.	Quasi TEM
D.	Microstrip line

A-1, B-1, C-2, D-3
A-1, B-2, C-2, D-3
A-2, B-2, C-3, D-3
A-3, B-1, C-2, D-2

⇒ If f(t) = - f(- t) satisfies Drichlet conditions, then f(t) can be expanded in Fourier series containing
only sine terms
only cosine terms
cosine terms and constant
sine terms and constant

⇒ The three sides of an admittance triangle denote
G, B, Y
R, X, Y
G, B, Z
(R, Y, Z) or (R, X, Z)

⇒ Which of the following statement is false?
The zener diode is uses as a constant voltage source
The SCR is a silicon rectifier with a gate electrode to control when current flows from cathode to anode
The gate electrode in the FET corresponds to the collector in a bipolar transistor
None of the above

⇒ Bit is a unit of
entropy
information
channel capacity
rate of information

⇒ An RL series circuit has an impedance of 20 Ω when frequency is 25 Hz. At f= 50 Hz, the impedance will be
40 Ω
20 Ω
less than 40 W but more than 20 Ω
less than 20 W but more than 10 Ω

⇒ If e = 10 sin(10⁸ t + 3 sin 10⁴ t) then the deviation is
4.77 kHz
47.7 kHz
477 kHz
4770 kHz

⇒ As temperature increases the number of free electrons and holes in an intrinsic semiconductor
increases
decreases
remains the same
may increase or decrease

⇒ What does the B register contain after the first MOV B, A has been executed?
40 H
60 H
80 H
80 D

⇒ An RC impedance function has a constant value at s = 0. The last element in the first cauer synthesis
will be a capacitor
may be R or C
will be R
will depend on the behaviour of function at s = ∞

⇒

P(s) = s⁴ + s³ + 2s² + 4s + 3
Q(s) = s⁴ + 2s³ + s

Which one of the following statements in correct for above P(s) and Q(s) polynomials?
Both P(s) and Q(s) are Hurwitz
Both P(s) and Q(s) are non-Hurwitz
P(s) is Hurwitz but Q(s) is non-Hurwitz
P(s) is non-Hurwitz but Q(s) is Hurwitz

⇒ A λ/8 section of transmission line is determined of load impedance of (2 - j 5) Ω. If characteristic impedance of line is 10 Ω. Then input impedance of line is
10 Ω
(6.9 + j 7.24) Ω
(1.75 + j 3.098) Ω
(2 - j 5) Ω

⇒ Voltage series feedback (Also called series-shunt feedback) results in
increase in both I/P and O/P impedances
decrease in both I/P and O/P impedances
increase in I/P impedance and decrease in O/P impedance
decrease in I/P impedance and increase in O/P impedance

⇒ Stability factor for S is given by for a fixed bias
1 + β
1 - β
1/β
β - 1

⇒ A rectangular waveguide measures 3 x 4.5 cm internally and has a 10 GHz signal propagated in it. Calculate the wave impedance for dominant mode.
130 p
1.3 p
120 p
12 p

⇒ It is required to measure angular position. Out of the transducers

Circular potentiometer
LVDT
E pick up
Synchro

The proper devices are
1, 2, 3, 4
2 and 3
1, 2, 4
1 and 4

⇒ The decorative lighting works on the principle of
periodic switching on and off
special inverter
rectifier
motor

⇒ The simplified logic expression for the circuit of the given figur
Y = A
Y = AB
Y = A + B
Y + A + B

⇒ A silicon sample A is doped with 10¹⁸ Atoms/cm³ of Boron. Another sample B of identical dimensions is doped with 10¹⁸ atoms/cm³ of phosphorus. The ratio of electron to hole mobility is 3. The ratio of conductivity of the sample A to B is
3
42738
42769
42796

⇒ A varactor diode is
reverse biased
forward biased
biased to breakdown
unbiased

⇒ In 8085 microprocessor the value of the most significant bit of the result following the execution of any arithmetic or Boolean instruction is stored in
the carry status flag
the auxiliary carry status flag
sign status flag
zero status flag

⇒ In a 3 phase full converter, the firing angle is less than 60°. The instantaneous output voltage
will have positive part only
will have both positive and negative parts
may have both positive and negative parts
will have negative part if load is inductive

⇒ A dc chopper V = 500 V feeds an electric fraction dc series motor. The chopping frequency is 400 Hz. The series inductance required to limit the maximum current swing to 10 A is
20 mH
about 31 mH
about 51 mH
about 92 mH

⇒ A meter has a resistance of 1 Ω and full scale deflection current of 1 mA. To convert into an ammeter of 1 A range, the shunt resistance should be
1000 Ω
1 Ω
0.01 Ω
0.001 Ω

⇒ A circuit using an op-amp is shown in the given figure. It
voltage series feedback
voltage shunt feedback
current shunt feedback
current series feedback

⇒ The M.K.S. unit of magnetic field intensity is
ampere
ampere/metre
volt
volt/metre

⇒ A thyristor has internal power dissipation of 40W and is operated at an ambient temperature of 20°C. If thermal resistance is 1.6° C/W, the junction temperature is
114°C
164°C
94° C
84° C

⇒

Assertion (A): Holes are majority carriers in p type semiconductor.

Reason (R): In p type semiconductor, the electrons produced by thermal agitation recombine with holes.

Both A and R are true and R is correct explanation of A
Both A and R are true but R is not correct explanation of A
A is true but R is false
A is false but R is true