Question is ⇒ In a manual shunt motor starter, Options are ⇒ (A) over load relay is connected in series and no volt relay in parallel with the load, (B) over load relay is connected in parallel and no volt relay in series with the load, (C) over load relay and no volt relay are both connected in series with the load, (D) over load relay and no volt relay are both connected in parallel with the load, (E) , Leave your comments or Download question paper.

Question is ⇒ In a manual shunt motor starter, Options are ⇒ (A) over load relay is connected in series and no volt relay in parallel with the load, (B) over load relay is connected in parallel and no volt relay in series with the load, (C) over load relay and no volt relay are both connected in series with the load, (D) over load relay and no volt relay are both connected in parallel with the load, (E) , Leave your comments or Download question paper. Previous question Next question


Q1.	In a manual shunt motor starter
A.	over load relay is connected in series and no volt relay in parallel with the load [Correct Answer]
B.	over load relay is connected in parallel and no volt relay in series with the load [Wrong Answer]
C.	over load relay and no volt relay are both connected in series with the load [Wrong Answer]
D.	over load relay and no volt relay are both connected in parallel with the load [Wrong Answer]
View Answer 5 -3 Explanation:- Answer : A Discuss it below : !! OOPS Login [Click here] is required to post your answer/result Help other students, write article, leave your comments

Previous question Next question

Also Read Similar Questions Below :

⇒ Which D.C. motor will be preferred for machine tools ?
Series motor
Shunt motor
Cumulative compound motor
Differential compound motor

⇒ In an overloaded motor main danger arises due to
winding getting overheated
busbars getting heated
starter getting damaged
bearings getting overheated

⇒ Compensating winding in a D.C. machine is placed
on yoke in the pole faces
on yoke in the interpolar gap
on armature
none of the above

⇒ If the speed of a D.C. shunt motor is increased, the back e.m.f. of the motor will
increase
decrease
remain same
become zero

⇒ If conditions for maximum power for a D.C. motor are established, the efficiency of the motor will be
less than 50%
60 to 70%
80 to 90%
1

⇒ Which method of braking is generally used in elevators ?
Plugging
Regenerative braking
Rheostatic braking
None of the above

⇒ For which application a D.C. motor is preferred over an A.C. motor ?
High speed operation
Low speed operation
Fixed speed operation
Variable speed operation

⇒ Which D.C. motor has got maximum self relieving property ?
Series motor
Shunt motor
Cumulatively compounded motor
Differentially compounded motor

⇒ The armature shaft of a D.C. motor must be able to withstand
any unbalanced magnetic pull on the armature core
twisting strains due to transmission of torque
bending moment due to the weight of the armature and commutator
all of the above

⇒ Which of the following motors have almost constant speed over their full load range ?
A.C. series motors
D.C. series motors
D.C. shunt motors
Low resistance squirrel cage motors

⇒ Which of the following D.C. motors has the least drop in speed between no-load and nominal load ?
Series motor without commutating poles
Series motor with commutating poles
Shunt motor with commutating pole
Compound motor without commutating poles

⇒ Torque developed by a D.C. motor depends upon
active length of the conductor
current flow through the conductors
number of conductors
radius of armature

⇒ A motor for punching machine is usually subjected to
no load
continuous part load
continuous full load
intermittent load

⇒ If the field circuit of a loaded shunt motor is suddenly opened
torque developed by the motor would be reduced to zero
it would race to almost infinite speed
it would draw abnormally high armature current
the fuse or circuit breaker will open the circuit before too much damage is done to the motor

⇒ The hysteresis loss in a D.C. generator varies with the frequency of magrietic reversals as
1/f
f
f^1.6
f²

⇒ Which of the following loss in a D.C. generator varies significantly with the load current ?
Field copper loss
Windage loss
Armature copper loss
None of the above

⇒ As the load is increased the speed of D.C. shunt motor will
reduce slightly
increase slightly
increase proportionately -
remains unchanged

⇒ Sparking is discouraged in a D.C. motor because
it increases the input power consumption
commutator gets damaged
both (a) and (b)
none of the above

⇒ As there is no back e.m.f. at the instant of starting, a D.C. motor, in order to prevent a heavy current from flowing though the armature circuit
a resistance is connected in series with armature
a resistance is connected parallel to the armature
armature is temporarily open circuited
a high value resistor is connected across the field winding

⇒ The function of a field regulator for compound motors is to
control the flux
limit the armature current
demagnetise the field partially
none of the above

⇒ The main disadvantage of the Ward- Leonard control method is
high initial cost
high maintenance cost
low efficiency at light loads
all of the above

⇒ Which D.C. motor will be preferred for cónstant speed line shafting ?
Cumulative compound motor
Differentially compound motor
Shunt motor
Series motor

⇒ Which of the following motor is preferred for operation in highly explosive atmosphere ?
Series motor
Shunt motor
Air motor
Battery operated motor

⇒ If t be the thickness of the laminations, then eddy current loss in a generator. will vary as
¹/_t
¹/_t²
t
t²

⇒ The condition for maximum efficiency for a D.C. generator is
eddy current losses = stray losses
hysteresis losses = eddy current losses
copper losses = 0
variable losses = constant losses

⇒ In a motor, energy conversion would not have been possible but for the
production of opposing back e.m.f. Eb in the armature
input energy from supply
use of commutator
application of Fleming's left-hand rule

⇒ The main disadvantage of Hopkinson's test for finding efficiency of the shunt D.C. motors is that it
needs one motor and one generator
requires two identical shunt machines
requires full-load power
ignores any change in iron loss

⇒ In D.C. machines the residual magnetism is of the order of
2 to 3 per cent
10 to 15 per cent -
20 to 25 per cent
50 to 75 per cent

⇒ The mechanical power developed by a shunt motor will be maximum when the ratio of back e.m.f. to applied voltage is
4.0
2.0
1.0
0.5

⇒ A three point starter is considered suitable for
shunt motors
shunt as well as compound motors
shunt, compound and series motors
all D.C. motors