Question is ⇒ In a CRO, the frequency of output of time base generator, Options are ⇒ (A) is only one constant value, (B) is adjustable, (C) varies automatically, (D) either (a) or (c), (E) , Leave your comments or Download question paper.

Question is ⇒ In a CRO, the frequency of output of time base generator, Options are ⇒ (A) is only one constant value, (B) is adjustable, (C) varies automatically, (D) either (a) or (c), (E) , Leave your comments or Download question paper. Previous question Next question


Q1.	In a CRO, the frequency of output of time base generator
A.	is only one constant value [Wrong Answer]
B.	is adjustable [Correct Answer]
C.	varies automatically [Wrong Answer]
D.	either (a) or (c) [Wrong Answer]
View Answer 3 -1 Explanation:- Answer : B Discuss it below : !! OOPS Login [Click here] is required to post your answer/result Help other students, write article, leave your comments

Previous question Next question

Also Read Similar Questions Below :

⇒ When a constant voltage source and constant current source are in series, the current source is ineffective.
TRUE
FALSE

⇒ A video monitor is exactly similar to TV receiver.
TRUE
FALSE

⇒ If f(- t) = f(t), the function f(t) has only cosine terms.
TRUE
FALSE

⇒ Video signals are transmitted through
amplitude modulation
frequency modulation
either amplitude or frequency modulation
neither amplitude nor frequency modulation

⇒ The voltage at which Avalanche occurs is known as
cut in voltage
barrier voltage
breakdown voltage
depletion voltage

⇒ The function off an oxide layer in an IC device is to

mask against diffusion or ion implantation
insulate the surface electrically
increase the melting point of Si
produce a chemically stable protective layer

1, 2, 3
1, 3, 4
2, 3, 4
4, 1, 2

⇒ The PIV of a bridge rectifier is less than that of full wave rectifier with centre tapped transformer.
TRUE
FALSE

⇒ A rectangular waveguide, in dominant TE mode, has dimensions 10 cm x 15 cm. The cut off frequency is
10 GHz
1 GHz
15 GHz
25 GHz

⇒ The ratio of impurity atoms to intrinsic semiconductor atoms in an extrinsic semiconductor is about.
0.0486111111111111
0.736111111111111
1 : 100000
1 : 10⁸

⇒

Assertion (A): Gate triggering is the most commonly used method for triggering of an SCR.

Reason (R): Even a small gate current is sufficient to turn on an SCR.

Both A and R are correct and R is correct explanation of A
Both A and R correct but R is not correct explanation of A
A is correct but R is wrong
A is wrong but R is correct

⇒ For a second order system the damping factor is varied from 0 to 1. The locus of poles is
a straight line on imaginary axis
a straight line on real axis
a semi circle
a circle

⇒ In the DRAM cell in the figure is the V_t of the NMOSFET is 1 V. For the following three combinations of WL and BL volta
5 V, 3 V, 7 V
4 V, 3 V, 4 V
5 V, 5 V, 5 V
4 V, 4 V, 4 V

⇒

Assertion (A): Double Kelvin's bridge is used to measure low resistances.

Reason (R): In low resistance, the contact and lead resistances are very important.

Both A and R are true and R is correct explanation of A
Both A and R are true but R is not correct explanation of A
A is true R is false
A is false R is true

⇒ A sinusoidal carrier voltage, having frequency 1000 Hz is amplitude modulated by a sinusoidal voltage of frequency 15 kHz. The frequency of upper and lower sidebands will be
1015 kHz and 985 kHz
1030 kHz and 970 kHz
13 kHz and 17 kHz
14 kHz and 16 kHz

⇒ For stable network the real parts of poles and zeros of driving point functions must be
negative
negative or zero
zero
positive

⇒ In 8086 a word OA 50 FH is stored in 02 and 03 memory locations. Then
OFH is stored at location 02 and 0 A 5 at location 03 and address of word is 02
OFH is stored at location 03 and 0 A 5 at location 02 and address of word in 02
OFH is stored at location 02 and 0 A 5 at location 03 and address of word is 03
OFH is stored at location 03 and 0 A 5 at location 02 and address of word is 03

⇒ The effect of source inductance in a 3 phase fully controlled bridge converter is to
decrease the output voltage
increase the output voltage
decrease the output voltage and increase the output current
increase the output voltage and decrease the output current

⇒ In the following limiter circuit, an input voltage V₁ = 10 sin 100pt applied. Assume that the diode drop is 0.7 V when it is forward biased. The zener breakdown voltage is 6
6.1 V, -0.7 V
0.7 V, -7.5 V
7.5 V, -0.7 V
7.5 V, -7.5 V

⇒ Which of the following amplifiers is used for impedance matching?
CE
CC
CB
Push pull

⇒ A 4 bit synchronous counter uses flip flops with a delay time of 15 ns each. The time required for change of state is
15 ns
30 ns
45 ns
60 ns

⇒ Let f₁(t) = G₁(t) + 4, f₂(t) = G₂(t) + 3. If G₁(t) and G₂(t) are uncorrected then the correlation between f₁(t) and f₂(t) are
12
7
6
zero

⇒ Dual slope ADC uses an op amp comparator.
TRUE
FALSE

⇒ The first and second subscripts in models of circular waveguides depict
the number of full sine wave variations in circumference in direction and Bessel function variations in radial direction respectively
the Bessel function variations in radial direction and the number of full sine wave variations in circumference direction respectively
the Bessel function variations in circumference direction and number of full sine wave variations in radial direction respectively
none of the above

⇒ In figure readings of the two voltmeters shoul
100 V on each meter
200 V on each meter
150 V on V₁ and 50 V on V₂
50 V on V₁ and 150 V on V₂

⇒ The symbol in figure is
SUS
SBS
Shockley diode
UJT

⇒ Which solid dielectric has highest temperature limit?
E
H
C
F

⇒ The maximum usable frequency for the 'E' layer is 10 MHz.
TRUE
FALSE

⇒ The carrier frequency will be if L = 50 µH and C = 1 nF.
512
612 kHz
712 kHz
812 kHz

⇒ ROC of sequence x[n] = δ[n] is
Not exist
z = 0
Entire Plane
Entire Plane expect z = 0, z = ∞

⇒ Drain feedback bias is often used with
D MOSFETs
E MOSFETs
both D and E MOSFETs
neither D nor E MOSFETs