Question is ⇒ In a common emitter circuit all voltages are measured with respect to, Options are ⇒ (A) base, (B) emitter, (C) collector, (D) base or collector, (E) , Leave your comments or Download question paper.

Question is ⇒ In a common emitter circuit all voltages are measured with respect to, Options are ⇒ (A) base, (B) emitter, (C) collector, (D) base or collector, (E) , Leave your comments or Download question paper. Previous question Next question


Q1.	In a common emitter circuit all voltages are measured with respect to
A.	base [Wrong Answer]
B.	emitter [Correct Answer]
C.	collector [Wrong Answer]
D.	base or collector [Wrong Answer]
View Answer 1 -1 Explanation:- Answer : B Discuss it below : !! OOPS Login [Click here] is required to post your answer/result Help other students, write article, leave your comments

Previous question Next question

Also Read Similar Questions Below :

⇒

Assertion (A): Acceptor extrinsic semiconductor has higher conductivity than intrinsic semiconductor.

Reason (R): Addition of p-type impurity produces an allowable discrete energy level just above valence band.

Both A and R are true and R is correct explanation of A
Both A and R are true but R is not correct explanation of A
A is true but R is false
A is false but R is true

⇒ A system is said to be static system, when present output depend upon
present I/P
presrent and past
present and future
past and future

⇒ Windows have a user friendly program called 'Front Page Express' for creating web pages.
TRUE
FALSE

⇒ In all metals
conductivity decreases with increase in temperature
current flow by electrons as well as by holes
resistivity decreases with increase in temperature
the gap between valence and conduction bands is small

⇒ If D is diameter of circular waveguide the cutoff wave-length for TE₁₁ mode is equal to
1.706 D
2.11 D
0.82 D
0.41 D

⇒ The percentage saving in power of 100% modulated suppressed carrier AM signal is
100
75
66.6
50

⇒ The purpose of impedance matching in an amplifier circuit is to achieve
high efficiency
reduce distortion
maximum power transfer
none of the above

⇒ UHF range is
30 MHz to 300 MHz
300 MHz to 3000 MHz
3000 MHz to 30, 000 MHz
above 30, 000 MHz

⇒ An RLC series circuit has R = 30 Ω, X_L = 30 Ω and X_C = 30 W. Its impedance is
30 ∠0°.
30 ∠45°
42.42 ∠45°
90 ∠45°.

⇒ In a parallel inverter
the commutating capacitor C is across the primary of transformer and the load is across the secondary
the commutating capacitor and load are connected across the secondary of transformer
the commutating capacitor C and load are connected in series and the combination is across the secondary of transformer
none of the above

⇒ The relative permeability of an iron specimen is 400 when B = 0.2 T. If B = 0.4 T, μ_r will be
400
less than 400
more than 400
more or less than 400

⇒ The phase velocity of an EM wave propagating in a hollow metallic rectangular waveguide in the TE₁₀ mode is
equal to its group velocity
less than the velocity of light in free space
equal to the velocity of light in free space
greater than the velocity of light in free space

⇒ A voltage v = 100 sin (100 pt + 45°) V is applied to an impedance 10 + j10 ohm. The current is
10 ∠45° A
7.07 ∠45° A
5 ∠45° A
5 ∠0 A

⇒ A 400 W carrier is modulated to a depth of 75 percent. The total power in modulated wave will be
38.5 W
400 W
512.5 W
615.5 W

⇒ Which solid dielectric has highest temperature limit?
E
H
C
F

⇒

Assertion (A): The circuit in figure produces repetitive narrow pulses when input is fed with sine or triangular waveform having peak value more than + V

Reason (R): The high gain op-amp produces voltages at two levels. If input is more than + V, the output is + 15 V otherwise the output is - 1
Both A and R are correct and R is correct explanation for A
Both A and R are correct but R is not correct explanation for A
A is correct R is wrong
A is wrong R is correct

⇒ For the polynomial P(s) = s⁵ + s⁴ + 2s³ + 2s² + 3s + 15 The number of roots which lie in the right half of the s plane is :
4
2
3
1

⇒ Two infinitely long wires carrying current are as shown in the figure below. One wire is in the y-z plane and parallel to the y-axis. The other wise is in the x-y plane and parallel to the x-axis. Which components of the resulting magnetic field are non-zero at the ori
x, y, z components
x, y components
y, z components
x, z components

⇒ A feedback network to be used with an amplifier to provide oscillation is tested and found to give an output of 0.124 V with a 0.5 V input. What percentage negative feedback should be introduced to the amplifier so that linear oscillations result?
0.0125
0.025
-0.0125
-0.025

⇒ The most commonly used magnetron is
cylindrical
parallel plate
inclined plate
flat plate

⇒ Maximum usable frequency is [f_muf]
f_c sec i
f_c cos i
f_c sin i
f_c sec i

⇒ Equipment using BCD numbers
pocket calculators
electronic counter
digital voltmeters
all of the above

⇒ In dc tacho generators used for measurement of speed of shaft, frequent calibration is necessary because
contacts wear off
strength of permanent magnet decreases with age
armature current produces heating effect
there is back emf

⇒ A half bridge inverter
needs a 3 wire dc supply
may use a two wire or 3 wire dc supply
has higher output voltage if fed from 3 wire dc supply
has higher efficiency if fed from 3 wire dc supply

⇒ A broadcast radio transmitter radiates 5 kW when the modulation percentage is 60. How much of this is carrier power?
6.66 kW
5 kW
4.9 kW
4.23 kW

⇒ To select one out of N equally probable events, the number of bits required is
log₂ N
log₁₀ N
log_e N
N

⇒ A 3 phase bridge inverter is fed by 400 V battery. The load is star connected and has a resistance of 10 Ω per phase. The peak value of load current is
40 A
20 A
0.416666666666667
0.208333333333333

⇒ Boolean algebra obeys
commutative law
associative law
distributive law
commutative, associative and distributive law

⇒ The signal input to a given amplifier is made up of 100 mΩ signal power and 1 mΩ noise power. The amplifier contributes an additional 100 mΩ of noise and has a power gain of 20 dB. The input signal-to noise ratio is
2
10
20
100

⇒ JFET is also known as
linear device
square law device
inverse law device
logarithmic law device