Question is ⇒ In a CMOS CS amplifier, the active load is obtained by connecting a, Options are ⇒ (A) p channel current mirror circuit, (B) n channel transistor, (C) p channel transistor, (D) BJT current mirror, (E) , Leave your comments or Download question paper.

Question is ⇒ In a CMOS CS amplifier, the active load is obtained by connecting a, Options are ⇒ (A) p channel current mirror circuit, (B) n channel transistor, (C) p channel transistor, (D) BJT current mirror, (E) , Leave your comments or Download question paper. Previous question Next question


Q1.	In a CMOS CS amplifier, the active load is obtained by connecting a
A.	p channel current mirror circuit [Correct Answer]
B.	n channel transistor [Wrong Answer]
C.	p channel transistor [Wrong Answer]
D.	BJT current mirror [Wrong Answer]
View Answer 1 -1 Explanation:- Answer : A Discuss it below : !! OOPS Login [Click here] is required to post your answer/result Help other students, write article, leave your comments

Previous question Next question

Also Read Similar Questions Below :

⇒ A carrier is modulated by two modulating waves A and B having modulation indices of 0.6 and 0.8 respectively. The overall modulation index is
1
0.7
0.2
1.4

⇒ From the given circuit below, we can conclude t
BJT is pnp
BJT is npn
transistor is faulty
not possible to determined

⇒ In 8085 microprocessor based system running at 3 MHz clock frequency what should be the minimum pulse width of the INTR signal, so that it is recognized successfully?
0.33 μs
0.666 μs
5.8 μs
none of these

⇒ The distance between maxima and minima of a standing wave is
λ/4
λ/2
λ
2λ

⇒ For a superconductor, the relative permeability is
zero
high
low
either low or high

⇒ A Darlington circuit is obtained by connecting
two CB stages in cascade
two CE stages in cascade
a CE stages followed by CB stage
two emitter follower in cascade

⇒ In the circuit shown in the figure the power dissipated in 30 Ω resistor will be maximum if the value of
30 Ω
10 Ω
9 Ω
zero

⇒ An arrangement of several individual antennas to spaced and phased that their individual contributions combine in one preferred direction and cancel in all other directions, to get greater directive gain or directivity, is known as
directional radiation of antennas
antenna gain stability
array of antennas
none of the above

⇒ The leads in a TRIAC are denoted by
anode cathode, gate
T₁ T₂, gate
T₁, T₂, anode
T₁, T₂, T₃

⇒ If the load current is high, the pressure coil of wattmeter should be connected directly across the load.
TRUE
FALSE

⇒ In a 4 input OR gate, the total number of High outputs for the 16 input states are
16
15
14
13

⇒ BCD numbers are useful whenever
binary to hexadecimal conversion is desired
binary to BCD conversion is desired
decimal information is transferred into or out of a digital system
none of the above

⇒

Match the following:

	List I		List II
A.	Digital counter	1.	Measurement of harmonics
B.	Schering Bridge	2.	Measurement of frequency
C.	Meggar	3.	Measurement of loss angle of dielectric
D.	Spectrum analyser	4.	Measurement of insulation resistance

A-1, B-2, C-3, D-4
A-4, B-3, C-2, D-1
A-2, B-3, C-4, D-1
A-4, B-1, C-3, D-2

⇒ Which rectifier has the best ratio of rectification?
Half wave rectifier
Full wave rectifier
Bridge rectifier
Three phase full wave rectifier

⇒ In figure, the switch is closed at t = 0. After some time i = 6A and rate of change of current was 4A/s. The value of inducto
1 H
1.5 H
indeterminate
0.5 H

⇒ The dynamometer principle can be used for
ammeter only
voltmeter only
wattmeter only
ammeter, voltmeter and wattmeter

⇒ If temperature is increased, the temperature coefficient of a metal
increases
decreases
may increase or decrease
remains constant

⇒ Automatic sensitivity control by target voltage control is easily possible in
Vidicon
Plumbicon
New vicon
both (b) and (c)

⇒ A digital clock uses __________ chip
SSI
LSI
VLSI
MSI

⇒ In an FM signal, the modulating frequency is 2 kHz and maximum deviation is 10 kHz. The bandwidth requirement is
2 kHz
10 kHz
5 kHz
32 kHz

⇒ A FET is a better clapper than a BJT because it has
lower off-set voltage
higher series ON resistance
lower input current
higher input impedance

⇒ For a BJT if β = 50, I_CEO = 3 μA and I_C = 1.2 mA then I_E
1 mA
1.2 mA
1.3 mA
1.4 mA

⇒ Which one of the following is non-resonant antenna?
Folded dipole
Broad side array
End fire array
Rhombic antenna

⇒ Tuned voltage amplifiers are not used
radio receivers
public address system
T.V. Receivers
band of freq. selected and amplified

⇒ In figure, D₂ turns on
v_i is more positive than V₁
v_i is less positive than V₁
v_i is more negative than V₂
v_i is less negative than V₂

⇒ In a series RLC circuit, the current at resonance is I₀ the total energy stored in the circuit at resonance is
LI₀²
2 LI₀²
2 LI₀²
0.5 LI²

⇒ The impedance 3.2 - j 12 in polar form is given as
6.4 ∠ - 75°
8.4 ∠ - 75°
10.4 ∠ - 75°
12.4 ∠ - 75°

⇒ In a positive edge triggered D flip flop
D input is called direct set
Preset is called direct reset
Present and clear are called direct set and reset respectively
D input overrides other inputs

⇒ A real number consists of
integer part
integer part and fraction part
integer part, fraction part along with positive or negative sign
none of the above

⇒ In a cellular communication system, path loss between transmitter and receiver is due to
scattering from building, trees, vehicles and other structure
reason at (a) above and due to reflections from ground only
reason at (a) and (b) above along with reflections from ionosphere only
reasons at (a), (b) and (c) above along with loss due to surface wave phenomenon