Question is ⇒ In a circular waveguide TE<sub>21</sub> mode has lowest cutoff frequency, Options are ⇒ (A) TRUE, (B) FALSE, (C) , (D) , (E) , Leave your comments or Download question paper.

Question is ⇒ In a circular waveguide TE<sub>21</sub> mode has lowest cutoff frequency, Options are ⇒ (A) TRUE, (B) FALSE, (C) , (D) , (E) , Leave your comments or Download question paper. Previous question Next question


Q1.	In a circular waveguide TE₂₁ mode has lowest cutoff frequency
A.	TRUE [Wrong Answer]
B.	FALSE [Correct Answer]
View Answer 1 -1 Explanation:- Answer : B Discuss it below : !! OOPS Login [Click here] is required to post your answer/result Help other students, write article, leave your comments

Previous question Next question

Also Read Similar Questions Below :

⇒ During fast forward operation of a tape recorder
all heads are withdrawn
all amplifiers are shut off
tape is not pressed against capstan
all of the above

⇒ For the system in the given figure G varies slightly, the ratio of open loop sensitivity to closed loop sensitivit
1 : (1 + GH)
1 : (1 + GH)^-1
1 : (1 - GH)
1 : (1 - GH)^-1

⇒

Assertion (A): A thermocouple transducer is based on Seeback effect.

Reason (R): In a thermocouple transducer used for temperature measurement, the cold junction is usually kept in ice bath.

Both A and R are true and R is correct explanation of A
Both A and R are true but R is not correct explanation of A
A is true R is false
A is false R is true

⇒ Which of the following wave remains unaffected during day and night?
Tropospheric wave
Sky wave
Ground wave
None of the above

⇒ For TE or TM modes of propagation in bounded media, the phase velocity is
independent of frequency
is a linear function of frequency
is a non-linear function of frequency
can be frequency dependent or frequency independent on the source

⇒ In ASCII, letter B is coded as
1000001
1000010
100100
1001000

⇒ A full adder is to be implemented using half adders and OR gates. A 4 bit parallel adder without any initial carry requires
8 half adders and 4 OR gates
8 half adders and 3 OR gates
7 half adders and 3 OR gates
7 half adders and 4 OR gates

⇒ In pulse code modulation, if the signal is sampled at the rate of f and the number of pulses in one code group is p, then the number of pulses per second will be
p/f
f/p
1/pf
pf

⇒ Two wattmeter method is suitable only for balanced loads.
TRUE
FALSE

⇒ Consider the following statemen
1, 2, 3, 4
1, 2, 3
1, 2
1, 3, 4

⇒ For the ring oscillator shown in the figure, the propagation delay of each inverter is 100 pico sec. What is the fundamental frequency of the oscillator output _______
10 MHz
100 MHz
1 GHz
2 GHz

⇒ Compared to bipolar junction transistor, a JFET has
lower input impedance
high input impedance and high voltage gain
higher voltage gain
high input impedance and low voltage gain

⇒ Thyristors are suitable for dc circuit breakers but not for ac circuit breakers.
TRUE
FALSE

⇒ For a sine wave the average value is calculated over half the cycle.
TRUE
FALSE

⇒ Which of the following instruments is used almost exclusively to measure radio frequency currents?
Moving coil
Rectifier
Moving iron
Thermocouple

⇒

Assertion (A): A class C amplifier is a timed amplifier which needs a tank circuit as the load in the collector circuit of the transistor for its proper operation

Reason (R): In class C operation collector current flows for less than 180° of the ac cycle and thus flows in pulses

Both A and R are correct and R is correct explanation for A
Both A and R are correct but R is not correct explanation for A
A is correct R is wrong
A is wrong R is correct

⇒ The energy of one quantum of light equal to hf.
TRUE
FALSE

⇒ In microwave system, waveguide twists
change the plane of polarization of a propagating wave
change the direction of a propagating wave
change the mode of a propagating wave
both (b) and (c)

⇒ A 75 ohm line is first short terminated and minima locations are noted. Then the short is replaced by resistive load and minima location are again noted. If minima location are not altered and VSWR is 3, the value of resistive load is
25 Ω
50 Ω
225 Ω
250 Ω

⇒ In setting up 'for' loops in Pascal, the initial and final values of index may be
integer constants
Integer constants or integer variable names
integer constants or integer variable names or integer expressions
integer constants or real constants

⇒ It is required to measure angular position. Out of the transducers

Circular potentiometer
LVDT
E pick up
Synchro

The proper devices are
1, 2, 3, 4
2 and 3
1, 2, 4
1 and 4

⇒ When the number of quantising levels is 16 in PCM, the number of pulses in a code group will be
3
4
8
16

⇒ For a rectified sinusoidal wave clipped at 0.707 its peak value (figure), the average valu
70.7 V
63.7 V
54 V
15 V

⇒ Wide banding technique is employed in the
video amplifier of a TV receiver
IF amplifier of an FM receiver
RF amplifier of an AM receiver
input section of a communication receiver

⇒ h parameters are used in transistor analysis.
TRUE
FALSE

⇒ The counter shown in the given figure is built using 4 -ve edge triggered toggle FFs. The FF can be set asynchronously when R = 0. The combinational logic required to realize a modulo-13 counte
F = Q₄ Q₃ Q₂ Q₁
F = Q₄ + Q₃ + Q₂ + Q₁
F = Q₄ + Q₃ + Q₂ + Q₁
F = Q₄Q₃Q₂Q₁

⇒

Match the following:

	List I		List II
A.	Title bar	1.	Window menu
B.	Control menu box	2.	First row of window
C.	start-button	3.	box in title bar
D.	Control	4.	Button on mouse

A-3, B-2, C-4, D-1
A-2, B-3, C-4, D-1
A-3, B-2, C-1, D-4
A-2, B-3, C-1, D-4

⇒ The Boolean expression for the sub-class (Q) of all electronic instruments which are measuring instruments or are non-digital instruments with battery supply is
Q = X(Y + Z)
Q = X + YZ
Q = XY + Z
Q = XY + Z

⇒ In a CD the sampling frequency is nearly
half the highest frequency in audio signal
equal to highest frequency in audio signal
double the highest frequency in audio signal
four times the highest frequency in audio signal

⇒ To convert JK flip flop to D flip flop
connect D to both J and K
connect D to J directly and D to K through inverter
connect D to K directly and D to J through inverter
connect D to K and leave J open