Question is ⇒ In a CE amplifier the Q point is very close to saturation point on the dc load line. This results in, Options are ⇒ (A) positive clipping of collector current, (B) negative clipping of collector current, (C) both positive and negative clipping of collector current, (D) either positive or negative clipping of collector current, (E) , Leave your comments or Download question paper.

Question is ⇒ In a CE amplifier the Q point is very close to saturation point on the dc load line. This results in, Options are ⇒ (A) positive clipping of collector current, (B) negative clipping of collector current, (C) both positive and negative clipping of collector current, (D) either positive or negative clipping of collector current, (E) , Leave your comments or Download question paper. Previous question Next question


Q1.	In a CE amplifier the Q point is very close to saturation point on the dc load line. This results in
A.	positive clipping of collector current [Correct Answer]
B.	negative clipping of collector current [Wrong Answer]
C.	both positive and negative clipping of collector current [Wrong Answer]
D.	either positive or negative clipping of collector current [Wrong Answer]
View Answer 2 -1 Explanation:- Answer : A Discuss it below : !! OOPS Login [Click here] is required to post your answer/result Help other students, write article, leave your comments

Previous question Next question

Also Read Similar Questions Below :

⇒ The reverse voltage applied to a varactor diode
is less than avalanche breakdown voltage
is more than avalanche breakdown voltage
may be more or less than a avalanche breakdown voltage
is very high as compared to avalanche breakdown voltage

⇒ An 8 bit wide 4 word sequential memory has
Eight 4 bit shift registers
Eight 8 bit shift registers
Four 8 bit shift registers
Foui 4 bit shift registers

⇒ In a single phase semi-converter the number of thyristors is
16
8
4
2

⇒ The pointer of an indicating instrument should be
very light
very heavy
neither heavy nor light
heavy

⇒ Gain stability in an oscillator can bs achieved by
providing negative feedback
providing positive feedback
using low Q circuits
controlling the gain

⇒ In 8085 the address space size is
64 kbits
64 k bytes
32 kbits
16 k bytes

⇒ The static characteristic of an adequately forward biased P-n junction is a straight line, if the plot is of __________ V_s → versus
log I V_s log V
log I V_s V
I V_s log V
I V_s V

⇒ In figure, the current
0.0416666666666667
0.0833333333333333
0.166666666666667
0.333333333333333

⇒ The more negative gate voltage, the conductive channel becomes
narrower
wider
thicker
linear

⇒ When the number of quantising levels is 16 in PCM, the number of pulses in a code group will be
3
4
8
16

⇒ If figure, I = 2A if R = 20 Ω. When R = 10 Ω current I
0.0416666666666667
0.0833333333333333
2.5 A
0.125

⇒ The essential condition for antenna array to be linear is that
individual antennas of the array must be of equal size
individual antennas of the array must be equally spaced along a straight line
any two individual antennas of the array must not be in the same direction
none of the above

⇒ Which of the following voltmeters would you use for measuring voltage across 20 kΩ resistance?
Voltmeter having a resistance of 5 kΩ
Voltmeter having a sensitivity of 1 kW/V
Voltmeter having sensitivity of 10 kW/V
None of the above

⇒ Maxwell's divergence equation for the magnetic field is given as
∇ . B = 0
∇² . B = 0
∇ . B = constant
∇² . B = constant

⇒ Coulomb friction is
the force of sliding friction between dry surfaces
the force of friction between moving surfaces separated by viscous fluid
the force required to initiate motion between two contacting surfaces
all of the above

⇒ Consider the following statements relating to synchros

Rotor of control transformer is either disc shaped or umbrella shaped
Rotor of transmitter has low magnetic reluctance
Transmitter and control transformer pair act as error detector

Out of above the correct statements are
1, 2, 3
1 and 2
2 and 3
1 and 3

⇒ A moving iron instrument can be used for
dc only
ac only
both dc and ac
dc and high frequency ac

⇒ Following figure repres
AND
OR
NAND
NOT

⇒ A Darlington pair is used for
low distortion
high frequency range
high power gain
high current gain

⇒ If B_max is the maximum flux density, eddy current loss is proportional to
B_max
B^1.6_max
B²_max
B³_max

⇒ Consider the following statements as regards noise

If Gaussian noise is applied at input of a rectifier, the output is not gaussian
The noise encountered on a telephone line consists of short, pulse type disturbances whose amplitude distribution is not Gaussian
Shot noise results from random emission of electrons from a cathode
Shot noise results from phenomenon associated with the flow of current across semi conductor junctions

Which of the above are correct?
1, 2, 3, only
1, 2, 4 only
1, 2, 3, 4
2, 3 only

⇒ The analog signal m(t) is given below m(t) = 4 cos 100 pt + 8 sin 200 pt + cos 300 pt, the Nyquist sampling rate will be
1/100
1/200
1/300
1/600

⇒ The Ebers-moll equation for I_E in CB configuration is given by
I_E = a_nI_CI_EC0
I_E = a_II_C + I_C0
I_E = a_nI_C + I_C0(e^qVEB/KT-1)
I_E = a_II_C + I_E0(e^qV_EB/KT - 1)

⇒ If a two port network is represented by an equivalent T network, the impedance of shunt arm in terms of ABCD parameters is equal to
1/C
(A - 1)/C
1/B
(D - 1)/C

⇒ For a series R-L-C circuit, the characteristic equation is given
critically damped
underdamped
undamped
overdamped

⇒ For the time domain response shown in figure the
lies in left half plane
lies in right half plane
lies at origin
may be complex or imaginary

⇒ A D-flip-flop is
dial type flip-flop
delay flip-flop
differential flip-flop
digital flip-flop

⇒ Consider the following statements as regards IF in radio receivers

If IF is too high, poor selectivity and poor adjacent channel rejection could result
If IF is high, tracking difficulties increase
A very low IF makes selectivity too sharp
As IF is decreased, image frequency rejection becomes better

Which of the above are correct?
1, 2, 3, 4
1, 2, 3
2, 3, 4
1, 3, 4

⇒ A 555 timer can be used as
an astable multivibrator
monostable multivibrator
frequency Divider only
any of the above

⇒ The heat sink disposes off heat mainly by
radiation
natural convection
forced convection
conduction