Question is ⇒ In a 3 phase full wave regulator feeding a star connected resistance load the input voltage is 400 V line to line. The firing angle is 160°. The line to line output voltage would be, Options are ⇒ (A) 400 V, (B) about 100 V, (C) about 20 V, (D) zero, (E) , Leave your comments or Download question paper.

Question is ⇒ In a 3 phase full wave regulator feeding a star connected resistance load the input voltage is 400 V line to line. The firing angle is 160°. The line to line output voltage would be, Options are ⇒ (A) 400 V, (B) about 100 V, (C) about 20 V, (D) zero, (E) , Leave your comments or Download question paper. Previous question Next question


Q1.	In a 3 phase full wave regulator feeding a star connected resistance load the input voltage is 400 V line to line. The firing angle is 160°. The line to line output voltage would be
A.	400 V [Wrong Answer]
B.	about 100 V [Wrong Answer]
C.	about 20 V [Wrong Answer]
D.	zero [Correct Answer]
View Answer 1 -1 Explanation:- Answer : D Discuss it below : !! OOPS Login [Click here] is required to post your answer/result Help other students, write article, leave your comments

Previous question Next question

Also Read Similar Questions Below :

⇒ Unit doublet is the Laplace inverse of __________ .
1/s
s²
s
none of these

⇒

Assertion (A): In angle modulation the transmitted amplitude is constant.

Reason (R): Angle modulation has good immunity to noise and interference.

Both A and R are correct and R is correct explanation of A
Both A and R are correct but R is not correct explanation of A
A is correct but R is wrong
A is wrong but R is correct

⇒ The resonant frequency of the circuit shown in figure
1/22p Hz
1/2p Hz
1/4p Hz
1/2p Hz

⇒ PROM is
Permanent Read Only Memory
Polarized Read Only Memory
Positive Read Only Memory
Programmable Read Only Memory

⇒ The Hilbert transform of cos ω₁t + sin ω₂t is
sin ω₁t + cos ω₂t
sin ω₁t - cos ω₂t
cos ω₁t - cos ω₂t
- sin ω₁t + cos ω₂t

⇒ A step voltages is applied to RLC series circuit having R = 2 Ω, L = 1 H and C = 1 F. The transient current response will be
over damped
critically damped
under damped
any of the above depending the magnitude of voltage

⇒ For the design of a sequential circuit having 9 states, minimum number of memory elements required is
3
4
5
9

⇒ In an SCR, the anode current is controlled by
gate current only
external circuit only
both gate current and external circuit
none of the above

⇒ Decimal 43 in hexadecimal and BCD number system is respectively.
B2, 01000011
2B, 01000011
2B, 00110100
B2, 01000100

⇒ For a system to be designated as hi-fi, the signal to noise ratio should be at least
25 dB
50 dB
75 dB
100 dB

⇒ Tesla is unit of
Φ
B
H
MMF

⇒ Which binary addition is incorrect?
1001.1 + 1011.01 = 10100.11
100010 + 1000101 = 1001010
0.0011 + 0.1110 = 1.1
1011.01 + 1001.11 = 10111

⇒ The residual resistivity of a binary alloy at 0°K is
the sum of the residual resistivities of the component metals
the difference of the residual resistivities of the component metals
the product of the residual resistivities of the component metals
depend on the concentration of the minor component in the alloy

⇒ The no. of comparators required in a 3 bit comparator type ADC is
2
3
7
8

⇒ In the given figure shows a logic circuit. The minimum Boolean expression for this circui
A + B
A + B + C
AB + C
AB + AC + BC

⇒ In a carbon-zinc cell the function of the depolarizer is that
it synthesizes the decomposed electrolyte
it converts the produced hydrogen into water
it absorbs the oxygen produced in the cell
it prevents the fast chemical action on the zinc container

⇒ In a bipolar transistor which current is smallest
collector current
base current
emitter current
any of the three currents

⇒ Thevenin's impedance of an ac network is in general
resistance
R and L in series
R and C in series
Either R and L or R and C in series

⇒ In all pure metals, temperature coefficient of resistance is positive.
TRUE
FALSE

⇒ For what positive value of K does the polynomial s⁴ + 8s³ + 24s² + 32s + K have roots with zero real parts?
10
20
40
80

⇒ If the reverse voltage across a p-n junction is increased three times, the junction capacitance
will decrease
will increase
will decrease by an approximate factor of about 2
will increase by an approximate factor of about 2

⇒ In directional coupler of the given figure, the terms |S₁₄| and |S₂₃| of scattering matrix are ne
1 each
0.5 each
0.1 each
1 and 0.5 respectively

⇒ The number of digit 1 present in the binary representation of 3 x 512 + 7 x 64 + 5 x 8 + 3 is
8
9
10
12

⇒ In a certain network not containing any dependent sources, number of nodes = 4 and number of branches is equal to 6.
4
2
3
5

⇒ Consider the following statements:

The positiveness of coefficients of characteristic equation is necessary as well as sufficient condition for stability of first and second order systems.
The positiveness of coefficients of characteristic equation ensures negativeness of real roots but is not sufficient condition for stability of third and higher order systems.

Out of above statements:
only 1 is correct
both 1 and 2 are correct
only 2 is correct
both are wrong

⇒ An electric heater is controlled by thyristors through on-off control. If a = 0.4, the heating is
16% maximum
40% of maximum
60% of maximum
84% of maximum

⇒ The internal impedance of a source is 3 + j 4 Ω. It is desired to supply maximum power to a resistive load. The load resistance should be
3 Ω
4 Ω
7 Ω
5 Ω

⇒ In a shield helix
the spacing between adjacent turns is very large
the spacing between adjacent turns approaches zero
the spacing between adjacent turns approaches zero and wire thickness approaches zero
the spacing between adjacent turns is very large wire thickness approaches zero

⇒ Which of the following statement about modulation is correct?
It avoid use of antennas
It reduces bandwidth
It ensures transmission over long distances
It combines different transmissions

⇒ A 1000 kHz carrier is simultaneously modulated with 300 Hz, 800 Hz and 2 kHz audio sine waves. Which of the following frequency is least likely to be present in the output?
1002 kHz
1000 kHz
999.2 kHz
998.0 kHz