Question is ⇒ In 8086, Options are ⇒ (A) the registers SI and DI are used for string operation, (B) the registers CS and DS are used for string operation, (C) the registers SS and ES are used for string operation, (D) the registers SI and SP are used for string operation, (E) , Leave your comments or Download question paper.

Question is ⇒ In 8086, Options are ⇒ (A) the registers SI and DI are used for string operation, (B) the registers CS and DS are used for string operation, (C) the registers SS and ES are used for string operation, (D) the registers SI and SP are used for string operation, (E) , Leave your comments or Download question paper. Previous question Next question


Q1.	In 8086
A.	the registers SI and DI are used for string operation [Correct Answer]
B.	the registers CS and DS are used for string operation [Wrong Answer]
C.	the registers SS and ES are used for string operation [Wrong Answer]
D.	the registers SI and SP are used for string operation [Wrong Answer]
View Answer 1 -1 Explanation:- Answer : A Discuss it below : !! OOPS Login [Click here] is required to post your answer/result Help other students, write article, leave your comments

Previous question Next question

Also Read Similar Questions Below :

⇒ Two discrete time systems with impulse responses h₁[n] = δ[n - 1] and h₂[n] = δ[n - 2] are connected in cascade. The overall impulse response of the cascaded system is
δ[n - 1] + δ[n - 2]
δ[n - 4]
δ[n - 3]
δ[n - 1] + δ[n - 2]

⇒ Image frequency rejection mainly depends upon
detector
mixer
IF
RF

⇒ For a diamagnetic material, μ_r = 1.
TRUE
FALSE

⇒ If the inputs to a 2 input XOR gate are high then, the output is high.
TRUE
FALSE

⇒ A cycloconverter is
ac-dc converter
dc-ac converter
dc-dc converter
ac-ac converter

⇒ The horizontal intercept of dc load line is the same as ideal
cut off point
saturation point
operating point
quasi saturation point

⇒ An engineer designs an amplifier to have a voltage gain of 60, but when constructed it only had a gain of 50. How much feedback should be used to provide the desired level?
0.0003
0.0033
0.013
0.033

⇒ The dc voltage on plate modulated class C amplifier is 8 kV. If the peak modulating voltage is 4 kV, the peak RF voltage delivered to load is
32 kV
12 kV
0.5 kV
24 kV

⇒ 1 dB is equal to __________ nepier
8.6
6.8
8
0

⇒ When a circuit is excited by ac sinusoidal source, the admittance is obtained by letting s = jω in Y(s).
TRUE
FALSE

⇒

Match the following:

	List I (Types of N-bit ADC)		List II (Characteristics)
A.	Flash converter	1.	Integrating Type
B.	Successive	2.	Fastest converter approximation
C.	Counter ramp	3.	Maximum conversion time = N bits
D.	Dual slow	4.	Used a DAC in its feedback path

A-2, B-3, C-4, D-1
A-1, B-3, C-4, D-2
A-2, B-4, C-3, D-1
A-1, B-4, C-3, D-2

⇒

Match the following:

	List I (Operation in Basic)		List II (Priority)
A.	Exponentiation	1.	1
B.	Multiplication and division	2.	2
C.	Addition and subtraction	3.	3
D.	Expression within parenthesis	4.	4

A-1, B-2, C-3, D-4
A-2, B-3, C-1, D-4
A-4, B-3, C-2, D-1
A-2, B-3, C-4, D-1

⇒ In the FM wave described by equation v = 15 sin (4 x 10⁸ t + 3 sin 1100 t), the carrier frequency and signal frequency respectively are
63.66 MHz and 175 Hz
4 x 10⁸ Hz and 1100 Hz
175 Hz and 63.66 MHz
1100 Hz and 4 x 10⁸ Hz

⇒ The circuit in figure is switched on at t = 0. At any time t, i(t3 + 3e^-1
6 - 3e^-1
3 - 3e^-t
6 - 6e^-1

⇒ When an alternating current passes through an ohmic resistance the electrical power converted into heat is
apparent power
true power
reactive power
none of the above

⇒ Which of the following computer memories is fastest?
Cache
Primary
Mass storage
Off line back up

⇒ A transistor amplifier is operating in class A mode. If a transformer is connected for impedance matching, the efficiency will
increase
decrease
not be affected
increase or decrease

⇒ A step voltage E is applied to a series R-L circuit. The rate of change of current is maximum at t =
zero
infinity
L/R
R/L

⇒ Class A amplifiers are preferred when
minimum distortion is required
maximum voltage gain is required
output signal is desired in phase with input signal
signal having A.C. superimposed on D.C. are to be amplified

⇒ A rectangular metal waveguide filled with a dielectric of relative permittivity ε_r = 4, has the inside dimensions 3 x 1.2 cm, the cut off frequency for the dominant mode is
2.5 GHz
5 GHz
10 GHz
12.5 GHz

⇒ When sources of different frequencies feed a network the only method of solution is superposition theorem.
TRUE
FALSE

⇒ The power in the signal s(t) = 8 cos (20 p - p/2) + 4 sin (15 pt) is
40
41
42
82

⇒ In an integral controller
the output is proportional to input
the rate of change of output is proportional to input
the output is proportional to rate of change of input
none of the above

⇒ The direction of pick up in a CD is
linear from centre towards edge
linear from edge to centre
nonlinear from centre to edge
nonlinear from edge to center

⇒ If E is energy level of electron and E_F is Fermi level, then
all quantum states with E less than E_F will be occupied at T = 0
all quantum states with E less than E_F will be empty at T = 0
some quantum states with E less than E_F will be occupied at T = 0
none of the above

⇒ The resonant frequency of the circuit shown in figure
1/22p Hz
1/2p Hz
1/4p Hz
1/2p Hz

⇒ The log magnitude curve for a constant gain K is a horizontal straight line at a magnitude 20 log K dB.
TRUE
FALSE

⇒ Which of the following expressions is true for apparent power in an A.C. circuit?
VI cos Φ
V_av x I_av
V_r.m.s x I_r.m.s
V_peak x I_peak

⇒ The attenuation in a waveguide near the cut off frequency is
zero
low
high
very high

⇒ Which of the following methods does not cause any reduction in instruction length?
Using program counter
Common source and destination address
Implicit source and destination address
Machine language programming

Users Also Read
Previous Papers

Aptitude

Reasoning

Gen.Knowledge

Speak English

English / Verbal

Online / Mock Test

Vedic Math