Question is ⇒ Impedance inversion may be obtained with, Options are ⇒ (A) half wave line, (B) a short circuited stub, (C) complex impedance Z connected in series with line, (D) quarter wave line, (E) , Leave your comments or Download question paper.

Question is ⇒ Impedance inversion may be obtained with, Options are ⇒ (A) half wave line, (B) a short circuited stub, (C) complex impedance Z connected in series with line, (D) quarter wave line, (E) , Leave your comments or Download question paper. Previous question Next question


Q1.	Impedance inversion may be obtained with
A.	half wave line [Wrong Answer]
B.	a short circuited stub [Wrong Answer]
C.	complex impedance Z connected in series with line [Wrong Answer]
D.	quarter wave line [Correct Answer]
View Answer 1 -2 Explanation:- Answer : D Discuss it below : !! OOPS Login [Click here] is required to post your answer/result Help other students, write article, leave your comments

Previous question Next question

Also Read Similar Questions Below :

⇒ Consider the following about 'return' statement in C

On executing the return statement, it immediately transfers the control back to the calling program.
There is no restriction on the number of 'return' statements present in a function.
The 'return' statement must be present at the end of called function.

Which of the above are correct?
All
1 and 2 only
1 and 3 only
2 and 3 only

⇒ Antiferromagnetic materials do not have permanent dipoles.
TRUE
FALSE

⇒ A memory system of size 16 K bytes is required to be designed using memory chips having 12 address lines and 4 data lines-each. The number of such chips required to design and the memory system is :
2
4
8
16

⇒ In a klystron amplifier the input cavity is called
buncher
catcher
Pierce gun
collector

⇒ Which of the following ICs has only one NAND gate?
7410
7420
7430
7447

⇒ Damping ratio =
actual resistance/critical resistance
critical resistance/actual resistance
critical resistance
none of the above

⇒ A transmitter serial current contains
carrier frequencies
audio frequencies
radio frequencies
none of the above

⇒ The radix of a hexadecimal system is
2
3
8
16

⇒ A rectangular waveguide measures 3 x 4.5 cm internally and has a 10 GHz signal propagated in it. Calculate the cut off frequency for dominant mode.
4 GHz
7.5 GHz
5 GHz
10 GHz

⇒ What is the direction of address
Unidirectional into μp
Unidirection out of μp
Bidirectional
Mixed direction, i.e., some lines into up and some others out of μp

⇒ The current in a circuit is measured using a 150 : 1 CT If the ammeter reads 0.6 A, the circuit current is
250 A
90 A
156 A
144 A

⇒ TRAP is __________ whereas RST 7.5, RST 6.5, RST 5.5 are __________ .
maskable, non-maskable
maskable, maskable
non-maskable, non-maskable
non-maskable, maskable

⇒ In a superheterodyne receiver, the IF stage has better selectivity than RF stage because
of higher frequency
of lower frequency
of high L/C ratio
of constant passband

⇒ In a superheterodyne radio receiver
RF amplifier normally operates at 455 kHz above carrier frequency
mixer input must be tuned to the signal frequency
local oscillator operates below signal frequency
local oscillator frequency is double the IF

⇒

Match the following:

	List I (type of controller)		List II (Operation)
A.	Pneumatic controller	1.	Flexible operation
B.	Hydraulic controller	2.	High torque high speed operation
C.	Electronic controller	3.	Fire and explosion proof operation

A-1, B-3, C-2
A-1, B-2, C-3
A-3, B-1, C-2
A-3, B-2, C-1

⇒ A piezoelectric force transducer has a charge sensitivity of 20 pC/N. It is connected to a charge amplifier and overall gain of transducer and amplifier is 50 mV/N. The gain of amplifier is
1 mV/pC
1.5 mV/pC
2.5 mV/pC
4 mV/pC

⇒ If the height of transmitting and receiving antenna in a LOS system are 49 meter and a 9 meter respectively then the distance up to which communication may be possible is about
40 km
110 km
400 km
1100 km

⇒ A reflex klystron oscillator is a
low power device
high power device
high efficiency device
both (a) and (b)

⇒ The mass of an electron is nearly
9.1 x 10^-27 kg
9.1 x 10^-29 kg
9.1 x 10^-31 kg
9.1 x 10^-35 kg

⇒ In Z_RC(s) has a pole at s = 0, the first element in second Foster realization is
R
C
R and C in series
R and C in parallel

⇒ If wave of critical frequency 30 MHz is departing at an angle of 60°, then the MUF is given to be
10 MHz
15 MHz
30 MHz
60 MHz

⇒

Assertion (A): The trigger circuit of a CRO is excited by the same signal as Y plates.

Reason (R): The time base generator develops a saw tooth voltage.

Both A and R are true and R is correct explanation of A
Both A and R are true but R is not correct explanation of A
A is true R is false
A is false R is true

⇒ When a line of any odd multiple of a quarter wavelength is short-circuited it represents
unit impedance
infinite impedance
zero impedance
none of the above

⇒ Consider the following statement S₁ and S_{2S₁ is False, S₂ is true
S₁ and S₂ both are true
S₁ and S₂ both are false
S₁ is true, S₂ is false}

⇒ The main difference between the broadside arrays and end fire arrays is that
individual elements are fed with same current in broadside arrays and of different magnitude in end fire arrays
in broadside arrays the elements are equidistant whereas in end fire array the distance between elements increases progressively
the total number of elements in broadside array is always one and a half times that of elements in end fire arrays
in broadside array the individual elements are fed in, out of phase by 180° whereas in end fire array individual elements are fed with currents of equal magnitude but their phases vary progressively along the line in such a way as to make the entire arrangement substantially unidirectional

⇒ When a p-n-p transistor is operating in active region, the current in the n region is due to
only holes
only electrons
mainly holes
mainly electrons

⇒ An RLC series circuit has R = 1 Ω, L = 1 H, C = 1 F. The damping ratio is
More than 1
1
0.5
Zero

⇒ For Ergodic Process
ensemble Average equal to time Average
ensemble Average is not equal to time Average
ensemble Average > Time Average
ensemble Average < Time Average

⇒ DC ampere hour meter is an indicating instrument.
TRUE
FALSE

⇒ A voltage V(t) which is a Gaussian ergodic random process with a mean of zero and a variance of 4 volt² is measured by a true rms meter. The reading will be
0
4
2
16