Question is ⇒ If WF is the Fermi level, then in a metal at T = 0, Options are ⇒ (A) all energy levels above WF filled, all those below WF are empty, (B) all energy levels below WF are filled, all those above WF are empty, (C) some energy levels, both below and above WF, are filled, (D) all energy levels below and above WF are filled, (E) , Leave your comments or Download question paper.

Question is ⇒ If WF is the Fermi level, then in a metal at T = 0, Options are ⇒ (A) all energy levels above WF filled, all those below WF are empty, (B) all energy levels below WF are filled, all those above WF are empty, (C) some energy levels, both below and above WF, are filled, (D) all energy levels below and above WF are filled, (E) , Leave your comments or Download question paper. Previous question Next question


Q1.	If W_F is the Fermi level, then in a metal at T = 0
A.	all energy levels above W_F filled, all those below W_F are empty [Wrong Answer]
B.	all energy levels below W_F are filled, all those above W_F are empty [Correct Answer]
C.	some energy levels, both below and above W_F, are filled [Wrong Answer]
D.	all energy levels below and above W_F are filled [Wrong Answer]
View Answer 1 -1 Explanation:- Answer : B Discuss it below : !! OOPS Login [Click here] is required to post your answer/result Help other students, write article, leave your comments

Previous question Next question

Also Read Similar Questions Below :

⇒ In case of stabilized reactance modulator AFC system
phase modulator is converted into frequency modulation by equalizer circuit
the discriminator must have a fast time constant to provide demodulation
the higher discriminator frequency, the better oscillator frequency
the discriminator frequency must be too low, or the system will fail

⇒ For a full wave bridge rectifier supplied with 50 Hz a.c., the lowest ripple frequency will be
50 Hz
100 Hz
200 Hz
400 Hz

⇒ Which inverter circuit uses coupled inductors?
Modified McMurray full bridge inverter
McMurray Bedford half bridge inverter
Modified McMurray Bedford half bridge inverter
Both (b) and (c)

⇒ Which of the following can be used as a buffer amplifier?
CE
CC
CB
Both (a) and (c)

⇒ Figure shows current pulses of a class C power amplifier. The fundamental frequency of these pulse
100 kHz
1000 kHz
10 kHz
1 kHz

⇒ A function is given f(t) = sin²t + cos²t. Which of the following is true?
f has frequency components at 0 and 1/2p Hz
f has frequency components at 0 and 1/p Hz
f has frequency components at 1/2p and 1/p Hz
f has frequency components at 0, l/2p and 1/p Hz

⇒ The probability giving distribution of electrons over a range of allowed energy levels is known as
Maxwell's Distribution
Fermi-Dirac Distribution
Richardson Dushman Distribution
none of the above

⇒ For the logic circuit given, what is the simplified Boolean funct
X = AB + C
X = BC + A
X = AB + AC
X = AC + B

⇒ Choose the correct option

Transit period is the time between two steady state
Transient Response is the response due to internal energy stored in circuit
Transit response is also called natural response
Transit response arises due to presence of C and L in the circuit
Transit is due to R, L, C in the circuit

4, 3, 2 , 1
5, 4, 3, 2
5, 4, 3, 1
5, 1, 4

⇒ If operator 'a' = 1 ∠120° then (1 - a) =
3
3 ∠ - 30°
3 ∠ + 30°
3 ∠60°

⇒ Choose correct option for a stable system :

Roots of the characteristic equation of the system are real and negative
Area within the impulse response is finite

I is true, II is true
I is true, II is false
I is false, II is true
I is false, II is false

⇒ A FET is to be operated as voltage variable resistor. For this drain to source voltage V_DS should be,
74
= V_P
< V_P
> V_P

⇒ The units for transconductance are
ohms
amperes
volts
siemens

⇒ A fully controlled bridge converter can operate in quadrants
1
1 and 2
1 and 3
1 and 4

⇒ The total number of leads in SCR, DIAC and TRIAC respectively are
3, 2, 3
2, 3, 3
3, 3, 2
3, 2, 4

⇒ Which of the following is not correct?
Voltmeter should have a very high resistance
An ammeter should have a very low resistance
A shunt should have a very low resistance
An electronic voltmeter draws appreciable current from source

⇒ The input to negative clamper has a peak value of V_p. Then in the output the positive and negative peaks are nearly
0 and -2 V respectively
V_p and -V_p respectively
2 V_p and 0 respectively
none of the above

⇒ An RLC series circuit has R = 1 Ω, L = 1 H, C = 1 F. The damping ratio is
More than 1
1
0.5
Zero

⇒ In a NOT gate the output is always the opposite of the input.
TRUE
FALSE

⇒ Which of the following is incorrect?
(8)₁₆ = (8)₈
(5)₁₆ = (5)₈
(8)₂ = (2)₁₀
(2)₁₆ = (2)₁₀

⇒ When a material becomes a superconductor, its resistivity becomes
very small
zero
about 10% of normal value
about 20% of normal value

⇒ Audio tapes have two tracks each 2.5 mm wide.
TRUE
FALSE

⇒

Assertion (A): Master slave JK flip flop is commonly used in high speed synchronous circuitry

Reason (R): Master slave JK flip flop uses two JK flip flops in cascade.

Both A and R are correct and R is correct explanation of A
Both A and R are correct but R is not correct explanation of A
A is true, R is false
A is false, R is true

⇒ ISDN stands for
Integrated Services Digital Network
Inter Services Digital Network
Inter Subscriber Digital Network
integrated Subscriber Digital Network

⇒ Bridge circuits using RTD in temperature measurement usually employ 3 lead system so as to obtain
higher sensitivity
better impedance matching
compensation for signal wire resistance
reduction in power consumption

⇒ If S represents the carrier synchronization at the receiver and r represents the bandwidth efficiency, then the correct statement for the coherent binary PSK is
r = 0.5, S is required
r = 1.0, S is required
r = 0.5, S is not required
r = 1.0, S is not required

⇒ A constant k low pass T section filter has a characteristic impedance of 600 p at zero frequency. At f = f_c the characteristic impedance is
600 Ω
zero
infinite
more than 600 ohms

⇒ Wagner earthing device eliminates
all stray capacitance in the circuit
stray capacitances between components
stray capacitance between detector terminal and ground
mutual coupling between components

⇒ When .4546 E 5 and .5433 E 7 are to be added in normalized floating point mode
none of the numbers is changed to any other form
.4546 E 5 is changed .004546 E 7 and .5433 E 7 is not changed
.5433 E 7 is changed to 54.33 E 5 and .4546 E 5 is not changed
both the numbers are changed and their exponents are made equal to 6

⇒ A sine wave with slew rate distortion looks like
step wave
square wave
triangular wave
cosine wave