Question is ⇒ If the speed of a D.C. shunt motor is increased, the back e.m.f. of the motor will, Options are ⇒ (A) increase, (B) decrease, (C) remain same, (D) become zero, (E) , Leave your comments or Download question paper.

Question is ⇒ If the speed of a D.C. shunt motor is increased, the back e.m.f. of the motor will, Options are ⇒ (A) increase, (B) decrease, (C) remain same, (D) become zero, (E) , Leave your comments or Download question paper. Previous question Next question


Q1.	If the speed of a D.C. shunt motor is increased, the back e.m.f. of the motor will
A.	increase [Correct Answer]
B.	decrease [Wrong Answer]
C.	remain same [Wrong Answer]
D.	become zero [Wrong Answer]
View Answer 5 -2 Explanation:- Answer : A Discuss it below : !! OOPS Login [Click here] is required to post your answer/result Help other students, write article, leave your comments

Previous question Next question

Also Read Similar Questions Below :

⇒ Which method of braking is generally used in elevators ?
Plugging
Regenerative braking
Rheostatic braking
None of the above

⇒ A D.C. series motor, as compared to shunt and compound motors, has the highest torque at the start because of its comparatively
stronger series field
lower armature resistance
large armature current
fewer series turns

⇒ D.C. motor is to drive a load which has certain minimum value for most of the time and some peak value for short duration. We will select the
series motor
shunt motor
compound motor
any of the above

⇒ If a D.C. motor is to be selected for conveyors, which motor would be preferred ?
Series motor
Shunt motor
Differentially compound motor
Cumulative compound motor

⇒ Sparking is discouraged in a D.C. motor because
it increases the input power consumption
commutator gets damaged
both (a) and (b)
none of the above

⇒ The speed of a D.C. motor can be varied by varying
field current
applied voltage
resistance in series with armature
any of the above

⇒ The speed of a D.C. series motor is
proportional to the armature current
proportional to the square of the armature current
proportional to field current
inversely proportional to the armature current

⇒ Small D.C. motors up to 5 H.P. usually have
2 poles
4 poles
6 poles
8 poles

⇒ The losses occurring in a D.C. generator are given below. Which loss is likely to have the least proportion ?
Magnetic losses
Armature copper losses
Mechanical losses
Field copper losses

⇒ Which of the following methods of braking is used in rolling mills ?
Dynamic braking
Plugging
Regenerative braking
Mechanical brakes

⇒ Which motor has the poorest speed control?
Differentially compounded motor
Cumulatively compounded motor
Shunt motor
Series motor

⇒ Which of the following statement is incorrect ? If a starter is not used with large D.C. motor, it will draw a starting current which
will produce very low starting torque
will produce excessive line voltage drop
will damage the cOmmutator
is many times its full-load current

⇒ By looking at which part of the motor, it can be easily confirmed that a particular motor is D.C. motor?
Frame
Shaft
Commutator
Stator

⇒ Which D.C. motor Will have least percentage increase of input current for the same percentage increase in the torque?
Shunt motor
Series motor
Cumulative compound motor
Separately excited motor

⇒ In a D.C. shunt motor, under the conditions of maximum power, the current in the armature will be
almost negligible
rated full-load current
less than full-load current
more than full-load current

⇒ The speed of a series motor at no load is
infinity
4000 r.p.m.
2000 r.p.m.
1000 r.p.m.

⇒ If a D.C. shunt motor is working at full load and if shunt field circuit suddenly opens
this will make armature to take heavy current, possibly burning it
this will result in excessive speed, possibly destroying armature due to excessive centrifugal stresses
nothing will happen to motor
motor will come to stop

⇒ Which of the following can be used to control the speed of a D.C. motor ?
Thermistor
Thyristor
Thyratron
Transistor

⇒ Which one of the following is not the function of pole shoes in a D.C. machine ?
To reduce eddy current loss
To support the field coils
To spread out flux for better uniformity
To reduce the reluctance of the magnetic path

⇒ For starting a D.C. motor a starter is required because
it limits the speed of the motor
it limits the starting current to a safe value
it starts the motor
none of the above

⇒ A direct on line starter is used for starting motors
up to 5 H.P.
up to 10 H.P.
up to 15 H.P.
up to 20 H.P.

⇒ The series parallel system of speed control of D.C. series motors widely used in traction work gives a speed range of about
1 : 10
1 : 8
1 : 6
1 : 4

⇒ Speed control of a cumulatively compounded D.C. motor can be effected through change of
field resistance
armature resistance
armature voltage
any of the above

⇒ In case the back e.m.f. and the speed of a D.C. motor are doubled, the torque developed by the motor will
remain unchanged
reduce to one-fourth value
increase four folds
be doubled

⇒ If T_a be the torque and Ia the armature current for a D.C. motor, then which of the following relation is valid before saturation ?
T_a ∝ I_a
T_a ∝ I/I_a
T_a ∝ I_a²
T_a ∝ ^I/_{I_a²}

⇒ Which of the following loss of D.C. motor decreases with increase in load ?
Friction and windage loss
Core loss
Brush contact loss
none of the above

⇒ Which one of the following is not necessarily the advantage of D.C. motors over A.C. motors ?
Low cost
Wide speed range
Stability
High starting torque

⇒ Usually wide and sensitive speed control is desired in case of
centrifugal pumps
elevators
steel rolling mills
colliery winders

⇒ If the terminals of armature of D.C. motor are interchanged, this action will offer following kind of braking
regenerative
plugging
dynamic braking
none of the above

⇒ Which of the following motors is most suitable for signalling devices and many kinds of timers ?
D.C. shunt motor
D.C. series motor
Induction motor
Reluctance motor