Question is ⇒ If the secondary burden of a CT 15 VA and secondary current is 5 A, the load impedance of CT is, Options are ⇒ (A) 0.6 Ω, (B) 5 Ω, (C) 6 Ω, (D) 10 Ω, (E) , Leave your comments or Download question paper.

Question is ⇒ If the secondary burden of a CT 15 VA and secondary current is 5 A, the load impedance of CT is, Options are ⇒ (A) 0.6 Ω, (B) 5 Ω, (C) 6 Ω, (D) 10 Ω, (E) , Leave your comments or Download question paper. Previous question Next question


Q1.	If the secondary burden of a CT 15 VA and secondary current is 5 A, the load impedance of CT is
A.	0.6 Ω [Correct Answer]
B.	5 Ω [Wrong Answer]
C.	6 Ω [Wrong Answer]
D.	10 Ω [Wrong Answer]
View Answer 1 -2 Explanation:- Answer : A Discuss it below : !! OOPS Login [Click here] is required to post your answer/result Help other students, write article, leave your comments

Previous question Next question

Also Read Similar Questions Below :

⇒ While keeping the down-link frequency constant, the diameter of a satellite antenna is reduced by half. To offer the same EIRP over the increased coverage area, the RF output power has to be increases by a factor of
2
4
8
16

⇒ In a N-P-N transistor the function of the emitter is
to emit or inject holes into the collector
to emit or inject electrons into the collector
to emit or inject electrons into the base
to emit or inject holes into the base

⇒ In a purely inductive circuit, the current __________ the voltage by __________ .
lags, 0°
leads, 90°
lags, 90°
lags, 45°

⇒ An RLC series circuit
resonant frequency is high
Q is high
bandwidth is large
Q is low

⇒ If C is thermal capacitance, m is mass of liquid and c is specific heat, then
C = mc
c = mC
m = cC
C = (mc)²

⇒ Consider the following statement : If a network has an impedance of (1 - j) as a specific frequency, the circuit would consist of series

R and C
R and L
R, L and C

Which of the statement are correct?
1 and 2
1 and 3
1, 2 and 3
2 and 3

⇒ The most important set of specifications of transformer oil include
dielectric strength and viscosity
dielectric strength and flash point
viscosity and flash point
flash point and viscosity

⇒ Which is correct for a transfer function?
The poles and zero must be complex
If the poles and zeros are complex or imaginary, they must be conjugate
If the poles and zeros are complex they must be simple
If a zero is imaginary, it must be simple

⇒ Which of the following cannot provide as much time interval accuracy as the oscilloscope but can capture and display eight or more signals simultaneously, something that scopes cannot do?
Logic analyzer
Digital oscilloscope
Frequency analyzer
Wave analyzer

⇒ In commercial electron tubes the current produced by the cathode at 1000 K is about
0.01 A per cm² of cathode surface
0.1 A per cm² of cathode surface
1 A per cm² of cathode surface
5 A per cm² of cathode surface

⇒ The Wheatstone bridge method of measuring resistance is ideally suited for the measurement of resistance values in the range of
0.001 to 1 Ω
0.1 to 100 Ω
100 Ω to 10 kΩ
100 kΩ to 10 MΩ

⇒ Which of the following is not treated as hexadecimal constant by assembler in 8085?
45 H
6 AFH
234
64 H

⇒ The time constant of the circuit in figur
RC
2 RC
3 RC
5 RC

⇒ In a 100% amplitude modulated signal, the power in the upper sideband when carrier power is to be 100 W and modulation system SSBSC, is
100 W
66 W
50 W
25 W

⇒ The minority carrier life time and diffusion constant in a semiconductor material are respectively 100 microsecond and 100 cm²/sec. The diffusion length is
0.1 cm
0.01 cm
0.0141 cm
1 cm

⇒ In figure, V_{0-1 V
2 V
+1 V
+15 V}

⇒ Denominator polynomial of a transfer function of certain network
stable
oscillatory
unstable
depends on numerator polynomial

⇒ Which of the following is correct in FORTRAN 77?
PARAMETER PMOS = 9.8, NMOS = X
PARAMETER (PMOS = 9.8, NMOS = X)
PARAMETER PMOS = 9.8, NMOS = X
PARAMETER PMOS, NMOS = 9.8, X

⇒

Assertion (A): A Smith chart can be used for a number of calculations of a transmission line

Reason (R): Smith chart is basically a polar impedance diagram.

Both A and R are correct and R is correct explanation of A
Both A and R are correct but R is not correct explanation of A
A is correct but R is wrong
A is wrong but R is correct

⇒ An RL impedance function can also be realized as
RC impedance function
RC admittance function
LC impedance function
LC admittance function

⇒ BCD number 1100111 = __________ ₁₀
66
67
68
69

⇒ The line of sight communication requires the transmit and receive antennas to face each other. If the transmit antenna is vertically polarized, for best reception to the receive antenna should be
horizontally polarized
vertically polarized
at 45° within respect to horizontal polarization
at 45° with respect to vertical polarization

⇒ The correct sequence of parts in klystron amplifier are
anode, catcher cavity, cathode, buncher cavity
cathode, buncher cavity, catcher cavity, cavity
anode, buncher cavity, catcher cavity, cathode
cathode, catcher cavity, anode, buncher cavity

⇒ Which of the following is the point of reference JFET?
Drain
Gate
Source
None of the above

⇒ Which of the following statement is correct?
The input impedance of CE amplifier is usually around 10 Ω
The voltage gain of a transistor amplifier in CE mode is always less than unity
The output impedance of a transistor amplifier is independent of the transistor configuration
The voltage gain of a transistor amplifier is independent of the load resistance

⇒ In figure (A) and
A represents PCM and B represents AM
A represents FM and B represents AM
A represents AM and B represents FM
A represents PCM and B represents FM

⇒ A 400 W carrier is modulated to a depth of 75 percent. The total power in modulated wave will be
38.5 W
400 W
512.5 W
615.5 W

⇒ In a series RLC circuit p.f is lagging when f < resonance frequency.
TRUE
FALSE

⇒ The scale of thermocouple instrument is linear.
TRUE
FALSE

⇒ The unit of ∇ x H is
Ampere
Ampere/meter
Ampere/m²
Ampere-meter