Question is ⇒ If the resolution of a printer is 1200 dpi, the number of dots per square inch is, Options are ⇒ (A) 1200, (B) 800, (C) 1200 x 1200, (D) either (a) or (b), (E) , Leave your comments or Download question paper.

Question is ⇒ If the resolution of a printer is 1200 dpi, the number of dots per square inch is, Options are ⇒ (A) 1200, (B) 800, (C) 1200 x 1200, (D) either (a) or (b), (E) , Leave your comments or Download question paper. Previous question Next question


Q1.	If the resolution of a printer is 1200 dpi, the number of dots per square inch is
A.	1200 [Wrong Answer]
B.	800 [Wrong Answer]
C.	1200 x 1200 [Correct Answer]
D.	either (a) or (b) [Wrong Answer]
View Answer 1 -2 Explanation:- Answer : C Discuss it below : !! OOPS Login [Click here] is required to post your answer/result Help other students, write article, leave your comments

Previous question Next question

Also Read Similar Questions Below :

⇒ The two modes of operation of three phase bridge inverters are known as
60° mode and 120° mode
90° mode and 120° mode
120° mode and 180° mode
120° mode and 240° mode

⇒ Which of the following microphones is the cheapest?
Moving coil
Condenser
Ribbon
Carbon

⇒ In which of the following logical group instructions of 8085 is the addressing mode 'immediate'?
ANA r
ANA M
ANI data
XRA r

⇒ In the given figure x_{6de(ax₁ + bx₂ + cx₃)
(a + b + c) (x₁ + x₂ + x₃) (d + e)
(ax₁ + bx₂ + cx₃) (d + e)
a b c d e (x₁ + x₂ + x₃)}

⇒ For formation of state equations, resistance of the circuit
should be in tree
should be in cotree
may be in tree or cotree
none of the above

⇒ In 8085 microprocessor, in order to enable INTR interrupt, which of the following instruction are needed?
EI only
SIM only
El and SIM both
None

⇒ In a horizontal polarized wave
magnetic field is perpendicular to ground
magnetic field component is parallel to ground
electric field component is perpendicular to ground
electric field is parallel to ground

⇒ In a three variable K map four adjacent cells give
single variable term
two variable term
three variable term
either (a) or (b)

⇒ Which of the following can be used to convert PPM into PWM?
Integrator
Astable multivibrator
Bistable multivibrator
Monostable multivibrator

⇒ Choose correct option for a stable system :

Roots of the characteristic equation of the system are real and negative
Area within the impulse response is finite

I is true, II is true
I is true, II is false
I is false, II is true
I is false, II is false

⇒ The given figure shows log magnitude versus ω plots of a system for different values of gain. For this sy
curve 1 shows highest gain margin and curve 2 shows poorest gain margin
gain margins shown by the three curves are equal
curve 1 shows poorest gain margin and curve 3 shows highest gain margin
curve 3 shows poorest gain margin while curve 1 shows highest gain margin

⇒ A boot strap generally incorporates
CB configuration
CE configuration
emitter follower
none of the above

⇒ In a CE amplifier, the output voltage is equal to product of
ac collector current and ac collector resistance
ac base current and ac collector resistance
ac emitter current and ac emitter resistance
ac collector current and source resistance

⇒ Consider the following sets of values of E, R and C for the circuit in the given fig
1 and 4
1 and 2
3 and 4
2 and 3

⇒ A p-n junction diode has
low forward and high reverse resistance
a non-linear v-i characteristics
zero forward current till the forward voltage reaches cut in value
all of the above

⇒ The superposition theorem is applicable to
linear, non-linear and time variant responses
linear and non-linear resistors only
linear responses only
none of the above

⇒ The response of a function is decided by
the location of its zeros
the location of its poles
both (a) and (b)
none of the above

⇒ In the vacuum diode equation i_b = ke_b^1.5, the current is
temperature limited current
space charge limited current
any of the above
none of the above

⇒ Read the following statements about 8085

RAL instruction rotates ACC contents left by 1 bit
When RAL instruction is executed once the binary number gets doubled
STC means set CY to 1

Which of the above statements are correct?
1 and 2 only
1, 2 and 3 only
1, 2 and 4 only
1 and 4 only

⇒ In a monolithic IC, resistors are formed from
ceramic material
manganin wire
P-type semiconductor
aluminium ribbon

⇒ If t_on and t_off are the turn on and turn off times of a thyristor, then
t_on and t_off are almost equal
t_on >> t_off
t_off >> t_on
t_on is about twice t_off

⇒ A discrete LTI system is non-casual if its impulse response is
aⁿ ∪(n - 2)
a^n-2 ∪(n)
aⁿ⁺² ∪(n)
aⁿ ∪(n + 2)

⇒

Assertion (A): A parallel resonant circuit is also called anti-resonant circuit.

Reason (R): In a parallel resonant circuit impedance is maximum at resonance.

Both A and R are true and R is correct explanation of A
Both A and R are true and R is not the correct explanation of A
A is true but R is false
A is false but R is true

⇒ The maximum phase difference between the applied voltage and current in a RLC series current with finite values of R, L, C, and f can be
less than 90°
less than 45°
180°
30°

⇒ A parallel plate capacitor has its length, width and separation doubled. It fringing effects are neglected, to keep the capacitance same, the dielectric constant must be
halved
kept the same
doubled
made 4 times

⇒ The output wave of a cycloconverter consists of a number of segments derived from the input wave.
TRUE
FALSE

⇒ In response to a unit step input the controller output in given figure is
proportional controller
proportional plus integral controller
integral controller
none of the above

⇒ If a sheet of a mica is inserted between the plates of an air capacitor, the capacitance
will increase
will return the same
will decrease
may increase or decrease

⇒ In calculating input impedance, the load impedance is considered to be connected at the output.
TRUE
FALSE

⇒ The pole zero diagram of an impedance Z has a pole at s = - 6 and zero at s = - 4 as shown in figure the constant multiplier k = 1. For a signal I_s = cos 6t, the steady state voltage across Z is given in magnitude as u
0.6
0.84
7.2
none